Reviews5v Reed Relay

Electronics-Salon 8 Channel DPDT Signal Relay Module Board (Operating Voltage: DC 5V)

  • 8 Channel DPDT Signal Relay Module Board, DC 5V Version..
  • FR-4 fiber glass PCB, dual copper layers. Dimensions: 72.5mm x 150mm ( L x W )..
  • RY5W-K high quality signal relays, LED indicator for each relay channel. Darlington transistors circuit driving relay, improve the reliability of action..
  • Pitch 3.81mm / 0.15" screw terminal block, wire range 26-16AWG, strip length 5mm / 0.2", Metric M2 slotted screw..
  • Datasheet: https://images-na.ssl-images-amazon.com/images/I/A1vg1+5HA8L.pdf.
Check Stock

Wireless Z-Wave Multi-Input/Output Dry Contact Bridge Cert ID ZC08-16040002

  • BEFORE YOU BUY: Check to make sure your home automation controller / security panel is interoperable with our device. NOT ALL Z-wave Controllers are....
  • One 24VDC / 110 VAC Relay to control any low voltage device via Z-wave. Controls garage doors, motorized shades, gates, solenoid valves, etc. Relay....
  • One SIGNAL Input terminal block to receive low voltage (digital, analog, or pulse) signals via Z-wave. Use with reed sensors, contact sensors, door....
  • 9V AC power adaptor included. Low voltage wire is NOT included.
  • Please visit our website and youtube page for application details and how-to video's. Wiring diagrams are also downloadable on our website product....
Check Stock

How to Use a Breadboard! (Make: Handbook)

  • 30A High Current 12V Contactor relay Switch DC power Switching Control Board.
  • Using high-quality ultra-small optocoupler, anti-interference ability, stable performance..
  • Using 9.5mm black fence terminal, standard 30A terminal, stable and solid, reliable quality..
Check Stock

ANMBEST 2PCS 4 Channel 5V Relay Module with Optocoupler High or Low Level Trigger Expansion Board for Raspberry Pi Arduino

  • It is 4 Channel Isolated 5V 10A Relay Module, each relay can individually switch on/off by an opto-isolated digital input, Standard interface can be directly connected with microcontrollers and be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, DSP, etc., very convenient..
  • Equipped with high-current relay, maximum load: AC250V 10A, 15A 125VAC, DC30V 10A.
  • RELIABLE: Fault-tolerant design, even if the control line breaks, the relay will not move.
  • With optical coupling isolation, triggering more reliable, more stable..
  • EASY to INSTALL: Equipped with screwed terminal plate and fixed bolt holes(diameter: 3.1 mm) on both sides for easy installation..
  • High/Low level trigger can be selected by jumper. Very versatile, you can reverse the input logic with the jumper..
Check Stock

Anfukone 4N35 Optocouplers Phototransistor 10 PCS

  • Industry Standard Dual-in line 6-pin package.
  • Applications: AC mains detection Reed relay driving,Telephone ring detection,Logic ground isolation,Logic coupling with high frequency noise rejection.
Check Stock

FAYLEZ 10 PCS 4N35 Optocouplers Phototransistor

  • Applications: AC mains detection Reed relay driving,Telephone ring detection,Logic ground isolation,Logic coupling with high frequency noise rejection.
  • Industry Standard Dual-in line 6-pin package.
Check Stock

Xiuxin 2pcs 5V 8 Channel Relay Module Board for Arduino PIC AVR DSP ARM

  • 2pcs/lot 8 Channel relay module board, Working voltage: 5V.
  • This board is for Arduino PIC AVR DSP ARM.
  • Support all single-chip microcomputer control,Industrial circle,PLC controller,Household intelligent control.
  • Relay output maximum contact is AC250V 10A and DC30V 10A.
  • Widely used for all MCU control, industrial sector, PLC control, smart home control..
Check Stock

SunFounder 2 Channel DC 5V Relay Module with Optocoupler Low Level Trigger Expansion Board Compatible with Arduino R3 MEGA 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi

  • 5V 2-Channel Relay interface board, and each one needs 15-20mA Driver Current.
  • Equiped with high-current relay, AC250V 10A.
  • Standard interface that can be controlled directly by microcontroller (compatible with Arduino ,Raspberry Pi, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
  • Indication LED's for Relay output status.
  • Size: 50.5mm(L) x 38.5mm(W) x 18.5mm(H)(1.99inch x 1.54inch x 0.73inch).
Check Stock

NOYITO 0-5A AC Current Detection Sensor Module Switch Output (DC 12V, Green)

  • Current detection range: AC 0-5A.003cbr003e.
  • Operating voltage: DC 5V / 12V / 24V ± 0.2V. (Select the corresponding version of the product according to your needs).003cbr003e.
  • Output mode: relay switching output.003cbr003e.
  • Relay load: AC 250V 10A Max , DC 30V 10A Max.003cbr003e.
  • Application: Intelligent trolley motor over-current detection, motor stall protection current detection, short-circuit protection detection, etc. (The second picture on the left is the schematic and the third picture is the wiring diagram)003cbr003e.
Check Stock

Dorhea ESP8266 ESP-12 NodeMcu D1 Module WeMos Lua 4M Bytes WLAN WiFi Internet Development Board + Relay Shield + 2.54mm 40Pin Single Row Male Pin Header - 3Set

  • The esp8266 module is 11 digital input / output pins, all pins with interrupt / PWM / I2C / support 1 line (except D0).
  • 1 analog input(3.2V max input). Micro USB connection.
  • WiFi internet development board 5V 1A switching power supply (switching power supply）onboard..
  • 5V relay shield is a digital switch to control much higher voltages and currents than esp8266 mini microcontroller, controlled by the D1 , the relay will switch to allow current to flow or turn off, depending on wiring..
  • 40 pin 0.1inch (2.54mm) male pin header connector PCB board pin strip electronic component, they are easy to be cut to any length if needed, you can cut or score with some electronic tool..
  • The pin header is an ideal connector for the PCB board and intergrated circuit, used widely in the computer and breadboard, compatible with raspberry pi or other electronic project..
Check Stock

QPKING Electric System Circuit Tester,Automotive Electrical System Tools,9V-30V Electrical System Diagnostic Tool With 2.4-inch LCD Display

  • [Multimeter Mode&Smart Test]: Electric System Tester is covered with comprehensive parameters of Multimeter, it can quickly test and automatically identified the Voltage, resistance, Positive and Negative poles of the tested component, which brings the user a lot of conveniences..
  • [Oscilloscope Mode&Relay Test]: Car Electric System Tester is not only able to display the parameter curve diagram of the tested component, such as voltage, frequency, time, etc, but also can test the common automotive relay, like 5-terminal relays, and 4-terminal relays..
  • [Component Activation&Injector Mode]: It can generate "Active" signals for components, such as lights, motors, and other on-board electronic devices. Also different pulse signals can be output to the injector, which provides 4 pulse modes to better detect the condition of the injector..
  • [0-5V Power Supply&Voltage Alarm]: Capable of setting 0-5V output voltage, used to verify the wiring condition of the tested component. Equipped with voltage setting alarm. If a short circuit or fault causes the voltage to be greater than or less than the set value, the device will alarm..
  • [Multi-language Feature]: 14 languages supported, English, Spanish, German, Russian, Italian, Polish, Portuguese, French, Vietnamese, Malay....
Check Stock