Reviews5v Relay Current Ratings

Painless Performance 80132 Single Pole, Double Throw Relay, 40 Amp

• ★ The 8-channel relay module is equipped with transistors, diodes and optocouplers to switch higher loads safely, reliably and with little power. The module is also equipped with generously dimensioned relays in order to be able to reliably carry out many switching processes..
• ★ 5V 8-channel relay module, each relay requires 70mA for switching (switching capacity AC: max. 250V / 10A.
• ★ 5V 8-channel relay module can be controlled directly with a microcontroller Raspberry Pi, Arduin, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic, etc..
• ★ The relay acts as a switch that responds to a signal from the Arduin. Because of this, it is widely used in IoT projects to control lights and other electronic devices..
• ★ Application: MCU control, PLC control, industrial area, smart home.If you need this relay, you can buy it directly. If there is a problem during use, you can contact us at any time to refund or replace it..

KNACRO 1-Channel 30A High Current 5V Contactor Relay Switch Power Switch DC Power Switching Control Board Module Electrical Relay switches for Cooler Heater Refit Water Heater Control (DC 5V)

• 30A High Current 12V Contactor relay Switch DC power Switching Control Board.
• Using high-quality ultra-small optocoupler, anti-interference ability, stable performance..
• Using 9.5mm black fence terminal, standard 30A terminal, stable and solid, reliable quality..

YWBL-WH Relay Module One Way 30A Optocoupler Isolation Relay Module High Power Relay High/Low Level Trigger YYG-2(5VDC)

• ANTI-INTERFERENCE---Made of the high quality miniature optocoupler, the relay module is of anti-interference ability, stable performance.
• STABLE AND RELIABLE---Adopting 9.5mm black barrier terminal and standard 30A terminal, the relay module is stable and reliable.
• HIGH/LOW LEVEL TRIGGER---The high/low level trigger of the relay module can be switched.
• DC5V/DC12V/DC24V---There are 3 styles for you: DC5V, DC12V, DC24V, you can choose one according to your preference.
• MAIN FEATURE---Product Name: Optocoupler Isolation Relay Module.
• Output Capability: AC 250V/30A, less than DC 30V/30A.

ARCELI 5PCS KY-019 5V One Channel Relay Module Board Shield for PIC AVR DSP ARM for Relay

4 pcs DC 5V 1 Channel Relay Module Board Shield High/Low Level Trigger with Optocoupler

• The module uses genuine quality relay, normally open interfaces.
• SMD optocoupler isolation, strong driving ability, stable performance.
• The module can be set high or low triggered by jumper.

5V ESP8266 Dual Channel WiFi Relay Module IOT Smart Home Phone APP Remote Switch with 100M Transmission Distance

• ON-BOARD ESP-01 WIFI MODULE: The relay board is equipped with on-board ESP-01 WiFi module and high performance microprocessor STM8S103..
• UART DEBUG INTERFACE: The relay has reserved UART debug interface and STM8 SWIM program download interface..
• SMART CONFIG TECHNOLOGY: The module uses smart config technology to complete the account and password configuration on the APP ESP-01 WiFi module on the mobile phone, and configure the username and password memory functions..
• ON-BOARD 5V RELAY: This relay module adopts On-board 5V,10A250V AC 10A30V DC relay, which can continuously pull 100,000 times with diode discharge protection and short response time..
• WORKING STATUS INDICATOR: The module has board mode selection and real-time working status indicator..

SainSmart USB 4 Channel Relay Automation (5V)

• NOYITO 2-Channel Micro USB Relay Module is equipped with a stable USB to serial port chip and a microcontroller. It can use the serial port debugging software to send serial commands on the computer to control the opening and closing of the 2-channel relay..
• Onboard high performance microcontroller chip, CH340 USB control chip.With power LED indicator and relay status LED.On-board 2-channel 5V, 10A/250VAC, 10A/30VDC relay, long relay life, can work 100,000 times continuously..
• Module with overcurrent protection and relay diode freewheel protection..
• NOYITO 8-Channel Micro USB Relay Module ASIN：B09RGTSHHW.
• NOYITO 4-Channel Micro USB Relay Module ASIN：B09RGVQXXT.

CGELE PID Temperature Controller Kit Voltage AC 100V to 240V Comes with SSR 40DA Solid State Relay, K Type Thermocouple Sensor, and Black Heat Sink

• ♥【What You Get】In this PID temperature controller kit,it include 1 x PID temperature controller,1 x solid state relay 40DA，1 x K type thermocouple，1 x heat sink..
• ♥【Product parameters】Power supply voltage:110-240VAC 50/60Hz.
• working environment:ambient temperature: 0℃~50℃,relative humidity: 35%~85% (no condensation) ；storage temperature：-25℃~65℃（avoid ice or dew）；resolution：1℃，0.1℃（adjustable）；wiring method：terminals；accuracy：+0.5%FS.
• installation environment:installation type ll, pollution grade 2 (IEC61010-1).
•  max current: 30mA, load resistance:≥1K..
• ♥【Feature】 Support 2 wire thermocouple input,1 way solid state relay output,1 way relay alarm output.
• digital display of real-time and set temperatures,adjustable degrees ℉ and ℃..
• ♥【Size】The panel size of PID temperature controller is 48(W)mmx48mm(L),install hole size is 46(W)mmx46mm(L).Total size:48mm(W)x48mm(L)x76mm(H).
• ♥【Widely application】Widely used in chemical industry, medical industry, product industry, machinery industry, greenhouse farming, agricultural planting, etc..

OONO DIN Rail Mount 30A/300V 2x12 Position Screw Terminal Block Distribution Module.

• DIN Rail mount 8 Channel 10Amp SPDT Power Relay Module, DC 5V Version..
• JS1-5V-F Power Relays. LED indicator for each relay channel. Darlington transistors circuit driving relay, improve the reliability of action..
• DIN rail mount carrier: High quality Taiwan DINKLE fireproof nylon material DIN rail mount carrier (not China low quality carrier), can support width 35mm / 32mm / 15mm rail. FR-4 fiber glass dual layers PCB..
• High quality terminal block: Pitch 5.0mm/0.197.

Solid State Relay, 90 to 280VAC, 25A

• Solid state relay module, long service life and high reliability, low drive voltage and current, widely used in many automatic control systems..
• Model: XRE-1D4840 Solid State Relay 40A DC to AC..
• Input voltage: 3-32V DC Output voltage: 24-480V AC.
• Note: The current of this product is 40A for a long time. A large heat sink or fan need to be added..
• Package Content: 2 x 40A Solid State Relay, ideal for automatic process control application, a must component for temperature controller and other machinery control system..

Two Position Low V Actuator w/End Switch

• Output: fan relay, alarm relay and 4-20ma current loop.
• Controls: buzzer, Digital display, latching relay, relay Delay, relay minimum runtime.
• Mounts on a standard 4” x 4” electrical box.
• 5 a spdt fan relay controls starters of exhaust fans.