Reviews5w Rf Module

11J28-06881 - Upgraded Replacement for Beacon-Morris Direct Spark Ignition Control Board

  • The Honeywell Home PROTAKEOVER is a module add-on for the Honeywell Home PROA7PLUS Alarm Panel. By installing this module, your PROA7PLUS will be able to support one of several legacy RF sensor lineups. You can pick between Honeywell 5800, 2GIG 345 MHz, 433 MHz, 319.5 MHz, and Bosch Sensors..
  • Once the PROTAKEOVER Module has been installed, it will replace the existing back plate for the PROA7PLUS Panel. The PROTAKEOVER serves as the back plate, as it also provides an antenna for communicating with the legacy sensors..
Check Stock

KOOBOOK 2Pcs Voice Playback Module MP3 Trigger Player Board SD/TF Card for Arduino

  • Smart voice module,integrated IO trigger, UART protocol control, One_line single-bus protocol control..
  • Standard MP3 and other 7 operating modes setting by DIP switch..
  • Speaker by a 5W class D audio amplifier on board..
  • Support TF card for maximum 32G downloading music files directly by micro USB connector..
Check Stock

Smart RF Relay Switch eMylo Wireless Remote Control Switch DC 12V One Channel Momentary Module 433Mhz Relay Receiver with Two Transmitters

  • ♥ RF Remote Control Switch: lamps or other household electric appliances are controllable using the remote control, which features long control distance, sensitivity, high anti-interference performance and stability..
  • ♥Excellent stability--The relay module provides high signal sensitivity at lower cost and resist interference.
  • ♥Strong signal--eMylo RF relay switch can pass through walls, floors and doors, control receiver from any place within a reliable distance.
  • ♥ More Flexibility & Widely Application: eMylo RF Relay Switch adopts non-directional wireless encoding technology, allowing independent control without mutual interference, can be used in industrial control and security fields, such as light, motor, remote controller, wireless security alarm, wireless door alarm, wireless controller, etc..
  • ♥Easy to set up:The programmable RF receiver and transmitter can be flexibly configured in quantity and in operating modes..
Check Stock

Marker (Radio Vrs. With Melody)

  • ...ight applications: interior light, dome light, map light, tail box light, side marker light, back up light, parking light, door light, turn signal light, tail light, license plate light, etc..
  • ⭐Common use for car, truck, motorcycle, scooter, trailer, RV, boat.with DC12V voltage. Fitment: Replacement LED bulb for: W5W 194 147 152 158 159 161 168 184 192 193 259 280 285 447 464 555 558 585 655 656 657 1250 1251 1252 2450 2652 2921 2825 921 906 579 and others..
  • ⭐The distance between the RF remote control with bulbs can reaches 12-30 meters.?No need pointing the RF remote control to bulbs and control all bulbs in within control.?Can control bulbs in the vehicle..
  • ⭐LED Chips Type: 3535 SMD, Chips QTY: 4 pcs/Bulb, Color: RGB 13colors, Voltage: DC 12V, Wattage: 6W/Pair, 3W/Bulb, Output: 0.25A/Bulb, Size: 1.5inx 0.43inx 0.45in (38mmx 11mmx 9mm), Lifetime: More than 30000 hours, Package: 4 pcs bulbs & 2 pcs RF remote.
Check Stock

Power Eject Bind RF IR LED Light Bluetooth Board Module Replacement Part for Microsoft Xbox One S Slim

  • Power Eject Bind RF IR LED Light Bluetooth Board Module Replacement Part for Microsoft Xbox One slim.
  • Tips: This is replacement to replace your old damage Power Eject Bind RF IR LED Light Bluetooth Board, don't include instructions, please install it....
  • Broken your Power Eject Bind RF IR LED Light Bluetooth Board ? don't need to change new device, just buy this item and replace your damage Power Eject....
  • Compatible with: Microsoft Xbox One Slim (Please check your model before your purchase).
  • Shipped by Amazon. Any questions, please contact us first, we will try our best to help you..
Check Stock

2902832, Frequency transducer, F Input: 0.002Hz-20kHz, Out: V/I, Screw Conn, Mini MCR-SL-F-UI-NC

  • -10dBm LO Power Consumption: Provides +24dBm third order intercept point, can achieve -10dBm LO power consumption, without high power LO drivers, there are no corresponding shielding and isolation problems, can improve system performance and reduce costs.
  • Wide Application: Suitable for applications such as RF‑IF down conversion in HF and VHF receivers, second mixer in base stations, DC baseband conversion, quadrature modulation and demodulation, and Doppler detection in imaging.
  • 10.3dB SSB Noise Figure at 70MHz: With the output amplifier and optimal source impedance of this mixer module, the SSB noise figure is 10.3dB at 70MHz. There is no insertion loss, no external duplexer, and no passive termination.
  • Single Power Supply: The mixer module is designed to be powered by a single power supply, and the RF, IF and LO ports have DC isolation capacitors for easy use.
  • Low Distortion and Wide Dynamic Range: AD831 is a low distortion, wide dynamic range, single chip mixer, very practical.
Check Stock

Mixer Module, 0.1‑500MHz Conversion Board High Frequency Transducer -10dBm for HF VHF Receiver for Quadrature Modulation for Base Station

  • -10dBm LO Power Consumption: Provides +24dBm third order intercept point, can achieve -10dBm LO power consumption, without high power LO drivers, there are no corresponding shielding and isolation problems, can improve system performance and reduce costs.
  • Wide Application: Suitable for applications such as RF‑IF down conversion in HF and VHF receivers, second mixer in base stations, DC baseband conversion, quadrature modulation and demodulation, and Doppler detection in imaging.
  • Low Distortion and Wide Dynamic Range: AD831 is a low distortion, wide dynamic range, single chip mixer, very practical.
  • 10.3dB SSB Noise Figure at 70MHz: With the output amplifier and optimal source impedance of this mixer module, the SSB noise figure is 10.3dB at 70MHz. There is no insertion loss, no external duplexer, and no passive termination.
  • Single Power Supply: The mixer module is designed to be powered by a single power supply, and the RF, IF and LO ports have DC isolation capacitors for easy use.
Check Stock

Mixer Module, 0.1‑500MHz Low Distortion High Frequency Transducer -10dBm Conversion for Base Station for Quadrature Modulation for HF VHF Receiver

  • -10dBm LO Power Consumption: Provides +24dBm third order intercept point, can achieve -10dBm LO power consumption, without high power LO drivers, there are no corresponding shielding and isolation problems, can improve system performance and reduce costs.
  • Single Power Supply: The mixer module is designed to be powered by a single power supply, and the RF, IF and LO ports have DC isolation capacitors for easy use.
  • 10.3dB SSB Noise Figure at 70MHz: With the output amplifier and optimal source impedance of this mixer module, the SSB noise figure is 10.3dB at 70MHz. There is no insertion loss, no external duplexer, and no passive termination.
  • Wide Application: Suitable for applications such as RF‑IF down conversion in HF and VHF receivers, second mixer in base stations, DC baseband conversion, quadrature modulation and demodulation, and Doppler detection in imaging.
  • Low Distortion and Wide Dynamic Range: AD831 is a low distortion, wide dynamic range, single chip mixer, very practical.
Check Stock

Professional RF Cable TV Signal Amplifier with High 40dB Gain

  • ...Adjustable gain/attenuation to reduce overdriving. Adjustable tilt compensation to allow large CATV systems to be properly balanced and mixed with other CATV or existing RF distribution system. Supports full TV frequency range from 40MHz to 860MHz for analog/digital cable TV, UHF and VHF channels. Anti-Interference module design with advanced noise filer built in..
  • -20 dB Output/Input Test Port is provided for easy trouble shooting. Thunder bolt protection with internal AC fuse built in for high voltage surge events. Aluminum chassis provides excellent heat dissipation and long durability..
Check Stock

HiLetgo RFID Kit - Mifare RC522 RF IC Card Sensor Module + S50 Blank Card + Key Ring for Arduino Raspberry Pi

  • The MF522-AN module design the circuit of card read by using the original Philips MFRC522 chip..
  • Easy to use, low cost, and applicable to equipment development and card reader development etc..
  • Applicable for the user who need to design or manufacture the RF card terminal..
  • The module can be directly loaded into the various reader molds..
  • The module use a voltage of 3.3V, it can connected communication with user's any CPU mainboard through several lines of SPI interface, it can ensure stable and reliable work, and reader distance..
Check Stock

JacobsParts WT32-ETH01 ESP32 Module Ethernet WiFi Bluetooth Development Board 100Mbps RJ45

  • The issue with the top soldered pins has been resolved, they are now shipping with separate unsoldered pins WT32-ETH01 is an embedded serial to Ethernet module based on the ESP32 series WT32-S1 MCU. The module integrates an optimized TCP/IP protocol stack, which is convenient for users to easily complete the networking functions of embedded devices while reducing development time cost. In addition, the module is compatible with half-pad and through-hole connectors..
  • The board width is a universal width and therefore, it can be directly soldered to boards, connectors, or even breadboards, which is convenient for users to use in different scenarios..
  • ESP32 series IC is an integrated 2.4GHz Wi-Fi and Bluetooth dual-mode SOC, with ultra-high RF performance, stability, versatility and reliability, as well as ultra-low power consumption..
  • ESP32 Module: WT32-S1 240MHz dual core microprocessor 4MB SPI flash memory Oboard 10/100Mbps RJ45 Ethernet (LAN8720A PHY) 802.11n WIFI Bluetooth 4.2.
Check Stock