ReviewsAc Control Board

XYGStudy Raspberry Pi Expansion Board Power Relay Module for Raspberry Pi 4 3 2 Model B B+ A+

  • Raspberry Pi Expansion Board, Power Relay.
  • The RPi Relay Board gives your Pi the ability to control high voltage/high current devices, easily makes normal home appliances become intelligent..
  • Standard Raspberry Pi 40PIN GPIO extension header, Supports Raspberry Pi A+/B+/2B/3B/3B+/4B and later versions.
  • High quality relays, loads up to 5A 250V AC or 5A 30V DC.
  • Photo coupling isolation, prevent interference from high voltage circuit.
Check Stock

Solidremote 12V - 24V Secure Wireless RF Remote Control Relay Switch Universal 2-Channel 433MHz Receiver with 2 FCC ID Transmitters for Garage Door Openers, Cars, LED Lights & More (KIT-1)

  • ... higher RF sensitivity -111dBm superheterodyne module for better long range and more stable performance. Also 433Mhz frequency is less crowded than 315Mhz in USA..
  • EASY & FLEXIBLE # Two independent relay channels can either work together (in latching) for polarity reversing or individually (in pulse / hold) to control different electronics, such as one channel for garage door controller unit, the other for entry lights. Easy programming & easy to use DIP switches working mode selection between pulse / momentary, hold / toggle and latching mode..
  • ENCLOSURE # Designed to work both indoor and outdoor, default enclosure supplied protects the inner radio receiver circuit board safe from rain or other tough weather, while customer can also use chemical glue or epoxy adhesive to seal the wiring holes after setup, providing IP55 equivalent waterproof protection level. Mounting holes are provided for easy installation to walls etc using screws..
  • INTERFACE # 3-Level efficient switching power supply system. Our 202U receiver board accepts 12 volts – 24 volts AC or DC wide supply voltage range (min. current rating is [email protected] DC). Each relay can switch up to 10A @14V DC or 10A @125V AC for resistive load (6A @14VDC for inductiv....
Check Stock

Impedance Analysis Module Wideband Logarithmic Amplifier 1.6mm Thick Double‑sided Board AD8302

  • Has the functions of remote system monitoring and diagnosis, return loss, and AC signal logarithmic ratio..
  • Using Printed Circuit Board1.6mm thick double‑sided board, the whole process of spraying tin to ensure good current passing performance..
  • Precise radio frequency power control, precise gain measurement scale, improve efficiency..
  • Measure gain, loss and phase up to 2.7GHz, dual demodulation logarithmic amplifier and phase detector, input range in 50Ω system ‑60dBm to 0dBm..
  • Various measurements, AD8302 can measure the gain and phase difference of amplifiers, mixers and other circuits..
Check Stock

VU Meter 2x Panel VU Meter Warm Back Light Recording & Audio Level Amp with Driver Board

  • L/GND/R: This driver board with low level signal input terminals for connections are CD players, computer sound cards, the first stage, and other audio signal source device, wiring L, GND, RW respectively: Left, the right channel.
  • Power Consumption:Input AC / DC 12V-15V power supply for the drive plate. (Recommended independent power transformer, or a separate power supply for the winding. the backlight current is 45 mA when drive plate off work.
  • 2 Resistor:R1 and R2 are two adjustable resistors of driver board,which can control the size of the hands swing..
  • Rectifier RegulatorThe backlight DC12V power meter is used for rectifier regulator of the backlight driver board Please notice that the positive and negative head interface..
  • Package Content:2 x VU Panel Meter+1 x Driver Module+1 x Cable.
Check Stock

SENCO 08T125W 8-Gauge 1-1/4 in. Collated Cement Board Screws (1,000-Pack) Pack of 2

  • 08T_W Series 08T125W Cement Board Screw with Nibs, #8 Thread, 1-1/4 in L, Flat Head, #2 Drive, Steel.
  • Cement board to wood screws with exterior finish..
  • For cement board to wood. Fits DS440AC (557.4876), DS425AC (557.4827), DS332AC (264.0720), DS212-18V (264.0662), DS312-18V (305.6512)..
Check Stock

ALMOCN 6Pcs DC 5V 1 Channel Relay Module With Optocoupler Isolation Support High or Low Level Trigger

  • The Relay Board Maximum load: AC 250V/10A, DC 30V/10A.
  • Using SMD optocoupler isolation, strong driving capability, stable performance..
  • Can be set high or low level trigger with jumper cap, to meet the demand of more trigger applications..
  • Fault-tolerant design, even if the control line is broken, the relay will not move..
  • Wide Application,The relay board works well with ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4 etc..
Check Stock

Terasic DE10-Lite

  • ANTI-INTERFERENCE & FASTER: This programmable logic controller uses industrial-grade 32-bit MCU with strong anti-interference and faster speed. The transmission baud rate is 9600..
  • PROGRAMMABLE IN LADDER LOGIC LANGUAGE: Program is written in ladder logic programming language, supports ladder logic programming language programming, downloading and monitoring, supports for GX-Developer, GX-work2..
  • SUPPORTS HMI CONNECTION: Supports HMI connection. Programming port is the port for program upload, download and HMI communication..
  • 16 POINT INPUT & 16 TRANSISTOR OUTPUT: The PLC board supports 16 point input and 16 transistor output. Y0-Y3 4 channels output 100k, 200MA, externally added with freewheeling diode up to 3A and Y4-Y17 for 24V, 3A..
  • WIDELY USED: Widely used for fields of printing, metallurgy, food, textile, packaging, home, building materials, plastics, chemicals. The industrial control board is powered by DC 24V. Do not input AC or 220V voltage..
Check Stock

KRXNY 1000W Power Inverter Pure Sine Wave 24V DC to 120V AC 60HZ with USB LCD Display for Car/Off Grid Solar

  • 1000W continuous 2000W peak true pure sine wave power inverter, as good as grid power, power backup for home power supply..
  • Transfer 24VDC to 110V~120VAC, 60Hz frequency, US outlets. Intelligent temperature control cooling fan. Earth connection for both PCB board and output. Digital LCD display..
  • High quality true copper inductance, filter the wave form, ensure the true pure sine wave AC output, safeguard your equipment. All big imported mosfets with strong driving capacity..
  • Thick PCB, allow the stronger current floating on the circuit, increase the load capacity. High frequency transformer to transfer DC to AC, ensure the stable and full AC output.
  • Free standard battery cables ( 55cm length ) and spare fuse for replacement..
Check Stock

How to Use a Breadboard! (Make: Handbook)

  • 30A High Current 12V Contactor relay Switch DC power Switching Control Board.
  • Using high-quality ultra-small optocoupler, anti-interference ability, stable performance..
  • Using 9.5mm black fence terminal, standard 30A terminal, stable and solid, reliable quality..
Check Stock

AOICRIE 12V 16-Channel Relay Interface Board Module Optocoupler LED LM2576 Power for Arduino DIY Kit PiC ARM AVR

  • ★12V 16-Channel Relay interface board, and each one needs 15-20mA Driver Current.
  • ★Equipped with high-current relay, AC250V 10A.
  • ★The control signal voltage range: the trigger signal is low 0-2V.
  • ★Standard interface that can be controlled directly by microcontroller (for Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP433, TTL logic).
  • ★DC 12V 16 Channel Relay Module Interface Board With Optocoupler Protection LM2576 Power for Arduino DIY Kit.
Check Stock

4 Axis Stepper Motor Nema 23 Dual Shaft 425oz-in 112mm+CW5045 Driver 4.5A 256 Microstep+5 Axis Breakut Board+400W 36V Power Supply CNC Controller Kit for CNC Router Engraver Milling Machine

  • ♞【Stepper Motor】4pcs 23HS2430B nema23 stepper motor.
  • ♞【Stepper Motor Driver】4pcs CW5045 driver, current: 1.3A-4.5A.
  • Driver microstep: 1 (1.8°), 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/5,....
  • ♞【Control Board】1pcs 5 Axis breakout boad with cables,this breakout board needs to be connected to the parallel port and USB port of the....
  • ♞【Power supply】1pcs 400W,36V/9.7A switching power supply.
  • ♞【Application】This cnc kit are widely used in engraving machine, printer, medical equipment, embroidery machine, stage lighting, textile....
Check Stock