ReviewsAdjustable Roller Assemblies

NTN Bearing 30206 Tapered Roller Bearing Cone and Cup Set, Steel, 30 mm Bore, 62 mm OD, 17.25 mm Width

  • 30206 Bearing Size: Out Diameter:62mm/2.44 inch.
  • Ealed bearings are lubricated with oil or grease in the bearing factory, while open and shielded bearings are meant to be lubricated in place, with periodic reapplication of lubrication, based on use.
  • Complete single tapered roller bearing assemblies are generally mounted in opposing pairs on a shaft to evenly distribute loads..
  • They incorporate logarithmic roller and raceway profiles with a optimized surface finish for ultimate roller to flange contact. These features result in reduced noise and smooth operation..
  • Widely used in transmissions, span styleoil or greased, high radial and axial load, trailer and caravan axles, gearboxes and differentials, span..
Check Stock

Gilson SS-15F Economy Sieve Shaker, 230V, 50 Hz, 11\ Length, 17\ Width, 30\ Height

  • Continuous or timed shaking up to 60 minutes in one-minute increments for ease of operation.
  • Adjustable mixing angle between 0 to 15˚ for precise results.
  • Rotary dial controls and amplitude adjustment arm for accurate mixing.
  • Side-arm assemblies with adjustable finger clamps holds eight 500mL or smaller flasks.
  • The Boekel 401000-2 Flask benchtop analog shaker uses 230V at speeds between 0 to 450 oscillations per minute, and has continuous or timed shaking, an adjustable mixing angle, and side-arm assemblies. This shaker reproduces the back and forth action of the human wrist. The unit has continuous or timed shaking up to 60 minutes in one-minute increments for ease of operation. An adjustable mixing angle between 0 to 15˚ provides precise results from a gentle swirl to vigorous agitation. Rotary dial controls and an amplitude adjustment arm provide accurate mixing. Two side-arm assemblies (included) hold eight 500mL or smaller flasks with adjustable finger clamps that can accommodate 1⁄4 to 2" diameter tubes and vessels. The shaker comes with a power cord, instructions, and two Allen wrenches: one 5/32" wrench for side arm installation and one 3/16" wrench for clamp adjustment. Laboratory shakers are used in many analytic procedures, including drug ....
Check Stock

Timken Tapered Roller Bearing Cup - 59429

  • Single cup (outer ring) for connecting to cones (inner ring assemblies, sold separately) to form a complete single tapered roller bearing.
  • Supports both radial and axial loads between a rotating and non-rotating member.
  • Operating temperatures range from -54 to 120 degrees C (-65 to 250 degrees F).
  • High alloy steel for durability and heat tolerance.
  • Open configuration for lubrication applied in place.
Check Stock

Timken Tapered Roller Bearing Cup - 59425

  • Single cup (outer ring) for connecting to cones (inner ring assemblies, sold separately) to form a complete single tapered roller bearing.
  • Supports both radial and axial loads between a rotating and non-rotating member.
  • Operating temperatures range from -54 to 120 degrees C (-65 to 250 degrees F).
  • High alloy steel for durability and heat tolerance.
  • Open configuration for lubrication applied in place.
Check Stock

Milodon 21523 8.25\ Oil Pump Shaft with Bronze Gear for Big Block Mopar

  • Manufactured from 4130 Chrome-moly shaft.
  • Distributor shaft and bronze gear for 383-440 and Hemi.
  • Bronze gear assemblies are for roller cams.
  • Induction heated-treated ends to reduce wear.
Check Stock

Makita 9032 4.4-Amp 3/8-Inch Variable Speed Belt Sander

  • Compact design for sanding in close quarters.
  • 8.2 feet power cord for increased maneuverability.
  • Variable speed control dial (980-5,600 ft./min.) enables user to match the speed to the application.
  • Adjustable sanding arm pivots 100° for hard-to-reach areas.
  • Easily adjustable belt tracking with a turn of a knob.
  • 3 different size arm assemblies and belts available (1/4″”, 3/8″”, 1/2″”) for increased versatility.
  • Electronic speed control dial (980 – 5,600-Feet/min.).
  • Adjustable sanding arm pivots 100-Degree for hard to reach areas.
  • 3 different size arm assemblies and belts available (1/4-Inch, 3/8-Inch, 1/2-Inch) for increased versatility.
Check Stock

OTC 4324 Stinger 1100 lbs Capacity Engine Support Bar

  • Engine support bar has a 1100 pounds capacity.
  • Features two hook assemblies for ease of use and tubular steel construction for long life.
  • Rubber padded support legs ensure stability during use.
Check Stock

SKF AS 4060 Thrust Roller Bearing Washer, Metric, 40mm Bore, 60mm OD, 1mm Width

  • Thrust washer for use with SKF AXK-series needle roller and cage thrust assemblies in applications where adjacent components cannot serve as raceways.
  • Spring steel with high yield strength for shock and vibration absorption.
  • Both sides of the washer are hardened and polished for use as raceway surfaces.
Check Stock

INA GS81126 Thrust Roller Bearing Housing Washer, Metric, 132mm ID, 170mm OD, 9mm Width

  • Housing locating washer for use with INA K-series axial cylindrical roller and cage assemblies in applications where adjacent components cannot serve as raceways.
  • Through-hardened carbon chromium steel for durability and resistance to deformity under heavy loads.
  • Precision-machined raceway for tighter tolerances than unground raceways.
Check Stock

INA GS81208 Thrust Roller Bearing Housing Washer, Metric, 42mm ID, 68mm OD, 19mm Width

  • Housing locating washer for use with INA K-series axial cylindrical roller and cage assemblies in applications where adjacent components cannot serve as raceways.
  • Through-hardened carbon chromium steel for durability and resistance to deformity under heavy loads.
  • Precision-machined raceway for tighter tolerances than unground raceways.
Check Stock

INA AS3047 Thrust Roller Bearing Washer, Metric, 30mm ID, 47mm OD, 1mm Width

  • Axial bearing washer for use with INA axial needle or cylindrical roller and cage assemblies in applications where adjacent components cannot serve as raceways and precise centering is not required.
  • Through-hardened chromium steel for durability and resistance to deformity under heavy loads.
  • Ground raceway for higher speeds and greater running accuracy than unground raceways.
Check Stock