ReviewsAluminum Thread Repair Sleeve

ABN 131-Piece Metric Thread Repair Set – Damaged Helicoil-Type Thread Master Repair Kit for Automotive Repairs

[Create Stronger Internal Threads]: The ABN Helicoil Rethreading Tool Kit Metric Stripped Thread Repair Kit is a course threads M5 to M12 restorer 131-piece set made of chrome-vanadium with stainless steel coils to restore damaged threads in steel, cast iron, and aluminum spark plug engine repairs, stripped oil pan drain plugs, and more.
[Contents]: Thread restorer kit metric set includes 5 insert installation tools, 5 lug break pin tools, 5 twist drill bits, 1 hex key, 5 thread taps, 110 wire thread inserts, carrying case, and instructions.
[Perfect Sizes]: Twist drill bit sizes 5.2mm, 6.3mm, 8.3mm, 10.5mm, 12.5mm.
Screw tap and thread insert sizes M5x0.8x6.7mm, M6x1.0x8.0mm, M8x1.25x10.8mm, M10x1.5x13.5mm, M12x1.75x16.3mm (where M12 means thread outer diameter = 12mm, 1.75 means pitch of thread = 1.75mm).
[Quick Organization]: Steel carrying case with latch and molded plastic inside tray insert to keep universal thread repair tool pieces separated and easy to access.
Includes bottom recesses for organizing the coils in included plastic bags.
[Easy to Use]: Remove your damaged thread by using an included twist drill bit.
Load the thread insert into installation tool.

Check Stock

Big-Sert 5382 3/8-24 Oversized Inch Thread Repair Kit

3/8-16 Starter bolt thread repair kit cast iron blocks or aluminum blocks P/n 1535 TIME-SERT.
TIME-SERT P/n 1535 Kit includes all the tools and 4 special inserts with straight section for bolt alignment built into the insert..
The stripped Starter bolt thread depth of the hole should be 1.200" inches or 30mm Depth minimum..
Note: This kit can also repair a failed coil style insert. The failed hole should not be larger than the drill included in kit which is .484 inches..

Check Stock

uxcell 5/8-11 UNC Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel

accuracy class: 6g. Made of alloy tool steel, hardness, high torque, good toughness and wear-resistance..
Applications: Can process, correct or clean the external threads. Suitable for general purpose threading in stainless steel, aluminum alloy, cast iron, copper, iron, aluminum, plastic, etc.. Great for maintenance and repair work on pipes, boards and machinery..
Features: Conical locking hole, strong locking and not loose. Perfect for re-threading existing threads in hard materials like metal and making new threads in soft material such as plastic. The surface is lubricated with grease to prevent rust, the thread is clear and easy to repair..
Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.....

Check Stock

uxcell 5/8-24 UNEF Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel

accuracy class: 6g. Made of alloy tool steel, hardness, high torque, good toughness and wear-resistance..
Applications: Can process, correct or clean the external threads. Suitable for general purpose threading in stainless steel, aluminum alloy, cast iron, copper, iron, aluminum, plastic, etc.. Great for maintenance and repair work on pipes, boards and machinery..
Features: Conical locking hole, strong locking and not loose. Perfect for re-threading existing threads in hard materials like metal and making new threads in soft material such as plastic. The surface is lubricated with grease to prevent rust, the thread is clear and easy to repair..
Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.....

Check Stock

uxcell 5/8-18 UNF Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel

accuracy class: 6g. Made of alloy tool steel, hardness, high torque, good toughness and wear-resistance..
Applications: Can process, correct or clean the external threads. Suitable for general purpose threading in stainless steel, aluminum alloy, cast iron, copper, iron, aluminum, plastic, etc.. Great for maintenance and repair work on pipes, boards and machinery..
Features: Conical locking hole, strong locking and not loose. Perfect for re-threading existing threads in hard materials like metal and making new threads in soft material such as plastic. The surface is lubricated with grease to prevent rust, the thread is clear and easy to repair..
Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.....

Check Stock

uxcell 3/8-16 UNC Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel

accuracy class: 6g. Made of alloy tool steel, hardness, high torque, good toughness and wear-resistance..
Applications: Can process, correct or clean the external threads. Suitable for general purpose threading in stainless steel, aluminum alloy, cast iron, copper, iron, aluminum, plastic, etc.. Great for maintenance and repair work on pipes, boards and machinery..
Features: Conical locking hole, strong locking and not loose. Perfect for re-threading existing threads in hard materials like metal and making new threads in soft material such as plastic. The surface is lubricated with grease to prevent rust, the thread is clear and easy to repair..
Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.....

Check Stock

E-Z Lok Threaded Insert, 18-8 Stainless Steel, Helical, #6-40 Internal Threads, 0.138\ Length (Pack of 10)

THREADED INSERT FOR METAL – E-Z LOK Coil Thread Inserts for metal. Also known as wire thread inserts or helical threaded inserts..
QUICKLY REPAIR DAMAGED THREADS – Quickly repair damaged threads or reinforce tapped holes in soft metals with this steel thread insert..
18-8 STAINLESS STEEL WIRE – 18-8 stainless steel threaded inserts that are resistant to corrosion and can withstand temperatures to 800°F..
FOR USE WITH APPLICATIONS – The threaded inserts are designed for use with soft metals: aluminum, cast iron, magnesium, etc..
STRONG THREADS MADE EASY – Before installation, the metal threaded insert diameter is larger than the hole and then reduced during installation..

Check Stock

uxcell M6 X 1.0 Metric Round Die, Machine Thread Left Hand Threading Die, Alloy Steel

accuracy class: 6g. Made of alloy tool steel, hardness, high torque, good toughness and wear-resistance..
Applications: Can process, correct or clean the external threads. Suitable for general purpose threading in stainless steel, aluminum alloy, cast iron, copper, iron, aluminum, plastic, etc.. Great for maintenance and repair work on pipes, boards and machinery..
Features: Conical locking hole, strong locking and not loose. Perfect for re-threading existing threads in hard materials like metal and making new threads in soft material such as plastic. The surface is lubricated with grease to prevent rust, the thread is clear and easy to repair..
Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.....

Check Stock

uxcell 1/2-20 UNF Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel

fine grinding. Made of alloy steel, hardness, high torque, good toughness and wear-resistance for long service life..
Applications: Can process, correct or clean the external threads. Suitable for general purpose threading in stainless steel, aluminum alloy, cast iron, copper, iron, aluminum, plastic, etc.. Great for maintenance and repair work on pipes, boards and machinery..
Features: Conical locking hole, strong locking and not loose. Perfect for re-threading existing threads in hard materials like metal and making new threads in soft material such as plastic. The surface is lubricated with grease to prevent rust, the thread is clear and easy to repair..
Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.....

Check Stock

uxcell M16 X 1.5 Metric Round Die, Machine Thread Right Hand Threading Die, Alloy Steel

accuracy class: 6g. Made of alloy tool steel, hardness, high torque, good toughness and wear-resistance..
Applications: Can process, correct or clean the external threads. Suitable for general purpose threading in stainless steel, aluminum alloy, cast iron, copper, iron, aluminum, plastic, etc.. Great for maintenance and repair work on pipes, boards and machinery..
Features: Conical locking hole, strong locking and not loose. Perfect for re-threading existing threads in hard materials like metal and making new threads in soft material such as plastic. The surface is lubricated with grease to prevent rust, the thread is clear and easy to repair..
Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.....

Check Stock

uxcell 1/2-13 UNC Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel

fine grinding. Made of alloy steel, hardness, high torque, good toughness and wear-resistance for long service life..
Applications: Can process, correct or clean the external threads. Suitable for general purpose threading in stainless steel, aluminum alloy, cast iron, copper, iron, aluminum, plastic, etc.. Great for maintenance and repair work on pipes, boards and machinery..
Features: Conical locking hole, strong locking and not loose. Perfect for re-threading existing threads in hard materials like metal and making new threads in soft material such as plastic. The surface is lubricated with grease to prevent rust, the thread is clear and easy to repair..
Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.....

Check Stock