ReviewsAnalog Board

ETEPON Digital Oscilloscope Kit with BNC-Clip Cable Probe with Power Supply, (Assembled Finished Machine) EM001

  • 【SIMPLE DESIGN】ETEPOPN EM001 oscilloscope kit is an assembled finished machine that can be used directly to avoid assembly/soldering process problems and saving you a lot of time. The display and MCU are mounted on the same board (motherboard) to avoid the use of inter-board pinouts. The analog channels are placed on a separate board containing most user-installed parts, thus allowing better separation of analog and digital circuits..
  • 【UPGRADED VERSION】The sensitivity of the EM001 oscilloscopes has been extended both in width and height which is wider and higher than the others It reaches 5mV / div – 20V / div while the others is only 10mV / div – 5v / div..
  • 【HAND-HELD】This updated digital oscilloscope can be hand-held while the others can only be used by placing it on the desktop..
  • 【ROTARY ENCODER】It has been added the rotary encoder makes parameter adjustment more quicker and easier..
  • 【WHAT YOU GET】You will get an assembled mini oscilloscope, BNC clip cable, and a power supply. Detailed operating instructions (troubleshooting guide) and schematics are also provided. If you have any questions about this digital oscilloscope, you can always contact us and we will reply within 24 hours..
Check Stock

Ximimark 5Pcs 16CH Analog Digital Multiplexer Breakout Board Module CD74HC4067 CMOS Precise Module For Arduino

  • This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067. This chip is like a rotary switch - it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (CHANxx)..
  • It works with both digital and analog signals (the voltage can’t be higher than VCC), and the connections function in either direction..
  • To control it, connect 4 digital outputs to the chip’s address select pins (S0-S3), and send it the binary address of the channel you want. This allows you to connect up to 16 sensors to your system using only 5 pins!.
  • Since the mux/demux also works with digital signals, you can use it to pipe TTL level serial data to or from multiple devices. For example, you could use it to connect the TX pins of 16 devices to one RX pin on your microcontroller. You can then select any one of those 16 devices to listen to. If you want two-way communications,you can add a second board to route your microcontroller's TX line to 16 device's RX lines. By using multiple boards, you can create similar arrangements for I2C,SPI,etc..
  • The internal switches are bidirectional, support voltages between ground and VCC, have low “on” resistance and low “off” leakage, and to prev....
Check Stock

PWM Signal Converter Module Digital to Analog Voltage Converter Adapter White

  • PWM voltage converter Convert 0-100% PWM digital signal into analog signal..
  • Signal interface switching between single chip or other industrial control board..
  • The power supply has the function of reverse connect protection, safe to use ..
  • Input digital signal can be 24V level 0-100%PWM signal. Output analog signal can be 0-10V voltage..
  • PWM signal receiving frequency range: 100hz-3khz, recommended 1khz-3khz..
Check Stock

Peavey VYPYR® X1 Guitar Modeling Amp

  • 36 on-board amp models including 6 acoustic and 6 bass amp models.
  • 12 stompbox effects with dual parameter control.
  • On-board looper with optional Sanpera(tm) footswitch.
  • 3.5mm aux in for connecting external audio sources.
Check Stock

XYGStudy for Raspberry Pi 4B/3B+/3B/2B/B+/A+ Jetson Nano High-Precision AD/DA Expansion Board Sheild Onboard ADS1256 DAC8552 ADC DAC Jumper

  • There’s no AD/DA function on the Raspberry Pi GPIO interface, this may trouble you in the Pi development. However, it won’t be a problem anymore. The High-Precision AD/DA Board allows you to add high-precision AD/DA functions to the Raspberry Pi..
  • Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano.
  • Onboard ADS1256, 8ch 24bit high-precision ADC (4ch differential input), 30ksps sampling rate. Onboard DAC8552, 2ch 16bit high-precision DAC.
  • Onboard input interface via pinheaders, for connecting analog signal. Onboard input/output interface via screw terminals, for connecting analog/digital signal. Features AD/DA detect circuit, easy for signal demonstration.
Check Stock

KEYESTUDIO MEGA Sensor Shield V1 for Arduino MEGA R3 2560 Prototype Board Projects

  • Nice Sensor shield of MEGA Rev3, Easy prototyping and Very convenient especially for 3PIN (G V S) connections. There are tons of ground and VCC headers making really it easy to connect various Arduino modules and sensors with DuPont style cables..
  • This sensor shield board really simplify the circuit and easily connect commonly used sensors.The board is having digital and analog interface, Bluetooth module communication interface, SD Card module communication interface, APC 220 radio frequency module interface, etc..
  • This sensor shield allows ease development and prototyping and makes convenient way to connect many external devices/sensors..
  • This board works well for prototyping or certain permanent applications and a very handy companion to an Mega Rev3 or compatible board..
  • 100% Compatible with the programming software for Arduino. Excellent shield board in good quality and packaged in a nice box! Great for all kinds of scientific experiment research for Arduino.
Check Stock

SparkFun MicroMod ATP Carrier Board-Modular Interface Ecosystem-Connect microcontroller/Processor Board to Various Carrier Board peripherals

  • Access all the pins (i.e. ATP) of the MicroMod Processor Boards with the SparkFun MicroMod ATP Carrier Board! This board breaks out the MicroMod Processor Board's pins on the M.2 connector to 0.1" spaced female headers and PTH pads on the edge of the board..
  • Features: M.2 Connector. Operating Voltage Range: ~3.3V to 6.0V (via VIN to AP7361C 3.3V Voltage Regulator). 3.3V (via 3V3).
  • Ports:1x USB type C, 1x USB type A Host, 2x Qwiic Enabled I2C, 1x CAN, 1x I2S, 2x SPI, 2x UARTs, 2x Dedicated Analog Pins, 2x Dedicated PWM Pins, 2x Dedicated Digital Pins, 12x General Purpose Input Output Pins, 1x SWD 2x5 header. Note: Depending on the design of the Processor Board, not all the pins may be accessible..
  • Additional Features: 1mAh battery backup for RTC. Buttons: Reset, Boot, LEDs. Power. 3.3V. Phillips #0 M2.5x3mm screw included.
  • Carrier board only. MicroMod processor board will be needed to use..
Check Stock

ONKYO A-9050 S Integrated Amplifier 100W + 100W 8Ω Silver Japan model

  • 60 W/Ch. (4 ohms, 20hz-20khz, 0.08% THD, 2 channels Driven, FTC) from high current power supply transformer and two High-grade customized capacitors.
  • Discrete Spectra module produces high instantaneous voltage for immersive sound Staging, improved instrument separation, and lively transient response.
  • Akm (AK4452) 768 kHz/32-bit digital-to-analog converter brings CD's and digital sources to life. For vinyl, a dedicated mm/MC circuit board and high....
  • DIDRC Filter Prevents Ultra-high-frequency Distortion Affecting Audible Sound.
  • 4 gold-plated analog RCA Audio inputs plus mm/MC phono input, 2 optical digital inputs, 2 coaxial digital inputs, 2 pairs of gold-plated speaker posts....
Check Stock

DEYUE 40PCs PCB Double-Sided Prototyping PCBs Circuit Boards Kit | 5 Size Universal untraced Perforated Printed Circuits Boards | Solder-able Circuit Protoboards for DIY Soldering Electronic Projects

  • 100 % SATISFACTION GUARANTED  ★  Excellent quality and an empty canvas for electrical enthusiasts! An easy soldering.
  • 0.1" hole spacing for DIP integrated circuits and headers..
  • THIS IS NOT YOUR NORMAL PERF BOARD!  ★  This board is much higher quality with plated-through-holes and annular rings that will not lift off the PCB under normal soldering conditions.
  • MUTI-PURPOSE ★ General purpose prototyping circuit board for analog and digital use.
  • Double sided board with plated-thru holes allows components to be easily soldered to either side of the board.
  • THE FLEXIBILITY OF HAVINg CHOICES  ★  Great assortment with variety of size and perfect for quickly prototyping stackable circuits.
  • PACKAGE COMPONENT  ★  40 Piece of double sided PCB prototype board in 5 different size (2x8 and 3x7 each 10 Pcs.
  • 7x9 cm each 4 Pcs) with mounting holes or slots on each board corner.
Check Stock

FainWan ACS712 Current Sensor Module Detector ACS712ELC 5A 20A 30A Amps Amperage Range (Pack of 2) (5A)

  • Pin 5V power supply, on-board power indicator.
  • The module can measure the positive and negative 20 amps, corresponding to the analog output 100mV / A.
  • There is no the detection current through, the output voltage is VCC / 2.
Check Stock

KEYESTUDIO Plus Board for Arduino UNO R3 with Type-C USB Cable, 3.3V 5V 1.5A Output Current, More Powerful Controller Board

  • The KEYESTUDIO Plus board can work like the Arduino Board but it is more powerful and has more pins.
  • The USB to Serial chip of this board is stable and compatible CP2102.
  • extend serial communication and I2C interface, 6 PWM and 6 analog ports.
  • special DC-DC design provides up to 5V 1.5A, can drive high-current devices like servo and motor.
  • The yellow text on black board makes identifying pinsets a breeze. FCC and CE is available.
  • How to use: Search for "keyestudio wiki KS0486" in Google Chrome to get the wiki online tutorial for this product. Technical supports are available at any time!.
Check Stock