ReviewsAngle Gage

Accusize Industrial Tools 81 Pcs Steel Gauge Block Set, Grade B, P900-S581

81 pc Grade B Steel Gage Block Set with MFG'S certificate.
Manufactured under carefully controlled conditions allowing for the highest degrees of accuracy when used at a temperature of 68 degrees F. (20 C)..
All gage block sets are assigned serial numbers and accompanied with a certificate of inspection listing the deviation for each block.
Each gage block set meets or exceeds federal specification ASME B89.1.9-2002..
Hardened to HRC 64 / All gage block sets are made to special standard to resist corrosion and defacement.

7.62 NATO CHAMBER HEADSPACE GAGE: The proper use of Headspace Gages is the most reliable way to test rifle chamber length. These rimless chambers require a slightly longer maximum headspace than commercial 308 Win calibers. The 7.62 NATO Headspace Gages do not conform to SAAMI tolerances..
MAXIMUM LENGTH: The Forster NATO Maximum rifle chamber gage checks to see that the rifle does not have excessive headspace, which could lead to dangerous pressure problems. The NATO Maximum Headspace Gage measures 1.6455″.
PRECISION MACHINED: Manufactured from top-quality, hardened steel and precision ground to ANSI and SAAMI tolerances. Headspace tolerance ground to a very exacting ±.00015..
QUALITY ASSURED: Each Headspace Gage thoroughly inspected with NIST-certified measurement tools to ensure the highest quality product..
MEASURING MEANINGFUL HEADSPACE: Properly speaking, and for safety purposes, one measures “headspace” as the difference between the length of a standard cartridge, as represented by a gage, and the gun’s actual chamber length , when the head of the cartridge is flush against the bolt face..

Fine thread Drywall--Sharp point: For attaching drywall to metal studs from 25 gage through 20 gage thick. Longer sizes are ideal for multiple layers or insulation. Fine thread Drywall--Drill point: Will drive easily through drywall, drill a hole in a steel stud up to 14 gage thick, and form its own mating thread. Can also be used for attaching plywood or insulation board to 14 gage metal.
Screws shall be quenched in liquid and then tempered by reheating to 650°F minimum.

Accurate Measurements: The bore gage features an electronic indicator with resolution of 0.00005"/.001mm and measuring depth of 9 inches.
Durable Construction: This electronic indicator provides both inch and metric readings.
two-point contact system is used to detect geometry problems such as ovality and taper.
carbide-tipped contact points provide extended wear and improved abrasion resistance.
The easily adjustable bore gage is self-centering and includes a 2-inch contact extension holder.
Minimum Hold Feature: This electric gage locks and holds the bore size as the gage is rocked within the part to be measured.
Set Includes: A storage case, 2 batteries, 15 measuring anvils, 4 spacers and an instruction manual.

Dillon Case Gage 45 ACP, Case Gage, reloading equipment, reloading parts, reloading accessories, 45 ACP case gage.

Gage increments are in .001" steps Minus tolerance: +0/-.0002". Fully hardened to 60-62 RC. Each gage is inspected and has a 10 Micron finish or better. Complete with plastic, element-proof fitted case..

Accurate Measurements: Used for accurately setting any bore gage up to 6" in diameter to an accuracy of 0.0001".
comes with a base anvil of 2.750" x 0.80" and 2 adjustable anvils of 2.375" x 0.375".
Bore Gage Capacity: This bore gage master has an internal capacity of 6.

It is 55 Degree Thread / Screw Pitch Gauge gage with lock up device. Typically used to check the thread size determination is correct.
Measuring Range: 4G, 4 1/2G, 5G, 6G, 7G, 8G, 9G, 10G, 11G, 12G, 13G, 14G, 16G, 18G, 19G, 20G, 22G, 24G, 25G, 26G, 28G, 30G, 32G, 36G, 40G, 48G, 60G, 62G.
It is useful to check the tool angle when cutting threads on a metal lathe.
Check the angle on the thread cutting tool on the V-groove of the gauge.
It was made by stainless steel, with wire drawing on the surface, not easy to rust. Ensure the accuracy of measurement.

Gage increments are in .001" steps Minus tolerance: +0/-.0002". Fully hardened to 60-62 RC. Each gage is inspected and has a 10 Micron finish or better. Complete with plastic, element-proof fitted case..

It is 60 Degree Thread / Screw Pitch Gauge gage with lock up device. Typically used to check the thread size determination is correct.
Measuring Range: 0.25, 0.3, 0.35, 0.4, 0.45, 0.5, 0.6, 0.7, 0.75, 0.8, 0.9, 1.0, 1.25, 1.5, 1.75, 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0, 5.5, 6.0.
It is useful to check the tool angle when cutting threads on a metal lathe.
Check the angle on the thread cutting tool on the V-groove of the gauge.
All 24pcs blades was made by stainless steel, with wire drawing on the surface, not easy to rust. Ensure the accuracy of measurement.

Made with durable heavy gage steel construction that includes six floor levelers for stability.
Product dimensions – 23.75” D x 50” W x 29.5” H | Full tilt – 44.25” H | Top dimensions – 23.75” D x 36” W | Weight – 56.2 lbs..
Top Angle Adjustment from Flat to 40 Degrees.