ReviewsArduino Antenna

ACEIRMC 6pcs Nano V3.0 3.0 Controller Terminal Adapter Expansion Board Nano IO Shield Simple Extension Plate for Arduino Mano AVR ATMEGA328P

Designed for Arduino for Nano V3.0: The item is a terminal expansion adapter, working very well for prototyping Arduino for Nano projects.
It lables for Arduino for Nano version 3.0, however you can still use this adapter for the older version (just have to remember that A0-A7 are in the reverse order)..
You can use this adapter to easily hook up for arduino for Nano to an outside world via hook up wires.
This item is a terminal expansion adapter, designed for Arduino Nano V3.0..
Nano Terminal Adapter Shield Expansion Board Compatible with Arduino Nano V3.0 AVR ATMEGA328P-AU Module.

Check Stock

Complete Ultimate STEM Electronic Projects Starter Kit for Arduino with Mega2560 LCD1602 Servo Stepper Motor Sensors Breadboard Jumper Wire Resistor Capacitor Transistor and Tutorial

This is an upgrade complete Arduino starter kit designed for beginners and electronic hobbyists..
With more than 33 projects, it is esay and convenient for you to learn Arduino and programming. If you need the guide of the projects, just email us after you getting the mega2560 starter kit...
The starter kit will make a great gift for any to-be engineers, or anyone looking to get a jump start in the world of microcontrollers and programming. Hundreds of tutorials and guides can be found online and the range of projects that can be created with an Arduino is vast.
This kit comes with everything that the average beginner Arduino project requires, plus more, 50 kinds of different electronic components, more than 180 components, such as Arduino Mega2560, 1602 LCD display are included. It has enough variety to learn most of what can be done with the arduino and electronics in general.
The kit is a great help for you learning electronics! Lots of little bits to start doing Arduino things.

Check Stock

DORHEA 10PCS NRF24L01+ 2.4GHz RF Radio/Wireless Transceiver Module Compatible with Raspberry Pi

NRF24L01 is a single chip radio transceiver for 2.4 - 2.5 GHz ISM band, low operating voltage : 1.9 ~ 3.6V low voltage operation..
Built-in hardware CRC error detection, Multipoint communication address control, built-in 2.4Ghz antenna, add wireless capability to your projects..
125 Communications channels frequency points, multi-point communication and frequency hopping to meet the communication needs..
Applications: wireless peripherals, remote control systems such as RC vehicles and consumer remote electronics, wireless voice transmission such as VoIP, wireless sensor networks, wireless networks, home and commercial automation. Compatible with Arduino and Raspberry Pi..
Maximum operating speeds up to 2Mbps, GFSK modulation efficiency, Anti-interference ability, Particularly suitable for industrial control applications, for easy implementation into designs without additional hardware..

Check Stock

GY-NEO6MV2 NEO-6M GPS Module NEO6MV2 with Flight Control EEPROM Controller MWC APM2 APM2.5 Large Antenna for Arduino Board Color GY-NEO6MV2 Set kit

With Flight Control EEPROM Controller MWC APM2 APM2.5 Large Antenna For Arduino Board.

Check Stock

GY-AS3935 Lighting Sensor Module SPI I2C MA5532-AE Lighting Strike Thunder Storm Distance Detector Breakout Board

Reference link: https://tinyurl(dot)com/AS3935-light-detector.
Video link: https://youtu(dot)be/oXqSIyaHR_I.
The splitter uses an inductor (antenna) designed specifically for this application, and the board is fully calibrated.This ensures that you can support low-level IC calibration without having to write a large back-end – focus on your end application!.
This sensor cannot drive an LCD display on it own It will need a microcontroller, like ESP8266/ESP32 or Arduino Pro Mini / Pro Micro 3.3V The Microcontroller will control the sensor and control the display as well..
What you will get is : 1 X GY-AS3935 Lightning Sensor.

Check Stock

2Pack 9V Battery Clip Connector Cable with Holder Box for Arduino UNO R3 Mega 2560 Power Module 6F22 6LR61 mn1604 pp3 Baterries

Standard 5.5x2.1mm Center Positive Barrel Jack DC Male Plug. Cable length: Approx. 20cm (7.8 inch)..
Widely Used for Arduino Uno, Arduino Due, Arduino Mega 2560, Arduino Ethernet Shield, development boards, evaluation boards, breadboard, Arduino DIY, DSO 138 OscillOscope kit, XR2206 function generator and the device which need the 9V battery..
Easy install & Save work: This cable come with a 9V battery holder and 3 screw fixing hole on the base, convenient for fixing.
With this snap cable, you can saves the work of soldering a battery snap to a DC coax plug. Don't always have to take apart/open some test equipment just to change the battery inside..
! ! ! Not fit for Arduino Nano, Effect pedals..
Any quality issues, please feel free to contact us..

Check Stock

6Pack 9V Battery Clip Connector Cable with Holder Box for Arduino UNO R3 Mega 2560 LED Strip Light Power Module 6F22 6LR61 mn1604 pp3 Baterries

Widely Used for Arduino Uno, Arduino Due, Arduino Mega 2560, Arduino Ethernet Shield, development boards, evaluation boards, breadboard, Arduino DIY, DSO 138 OscillOscope kit, XR2206 function generator and the device which need the 9V battery..
Easy install & Save work: This cable come with a 9V battery holder and 3 screw fixing hole on the base, convenient for fixing.
With this snap cable, you can saves the work of soldering a battery snap to a DC coax plug. Don't always have to take apart/open some test equipment just to change the battery inside..
Standard 5.5x2.1mm Center Positive Barrel Jack DC Male Plug. Cable length: Approx. 20cm (7.8 inch)..
Not fit for Arduino Nano, Effect pedals..
Any quality issues, please feel free to contact US..

Check Stock

AITRIP 3PCS Type-C USB ESP32 Development Board 2.4GHz WiFi Dual Cores Microcontroller Integrated with Antenna RF Low Noise Amplifiers Filters for Arduino

Low power consumption: the development board uses 2.4GHz dual-mode Wi-Fi, chip ESP-WROOM-32, and 40nm low power consumption technology.
2.4GHz Dual Mode WiFi + Bluetooth Development Board.
Durable material: This product is made of high-quality material, durable, long service time, firm and stable in use..
Package: You will get 3 Pieces Type-C USB ESP-WROOM-32 ESP32 ESP-32S Development Board 2.4GHz Dual-Mode WiFi + Bluetooth Dual Cores Microcontroller Processor Integrated with Antenna RF AMP Filter AP STA for Arduino IDE.

Check Stock

SparkFun Lightning Detector - AS3935 Add Lightning detection to your weather station Programmable detection level Distance to storm estimator Indoor-Outdoor setting SPI Interface 3.3V logic Small size

Detect lightning with ease. Solder headers on to connect to your microcontoller and go. (Arduino-Compatible).
Detects strikes from up to 40km away with accuracy of 1km in 14 steps. Enjoy studying the weather..
Includes a “Disturber” (false event) rejection algorithm. Avoid false positives and noise in your project..
Features a sensitive antenna tuned to pick up lightning events in the 500kHz band..
Supply Voltage: 2.4V-5.5V. Recommended 3.3V. 3.3V logic, be sure to use a logic level converter where needed..

Check Stock

9V Battery Holder E-outstanding 2PCS Black 6F22 9V Battery Storage Case Box with 2.1x5.5mm DC Male Plug and Wire Leads for Arduino UNO R3 Battery Clip Container

Made of high quality materials. Lightweight and easy to carry..
Designed with spring clips for easy battery installation and removal..
EASY TO INSTALL AND SAVE WORK: The cable comes with a 9V battery holder and 3 screw fixing holes on the base for easy fixation.
With this snap cable you can save yourself the work of soldering the battery snap to the DC coax plug.
Widely used in Arduino Uno, Arduino Due, Arduino Mega 2560, Arduino Ethernet Shield, Development Boards, Evaluation Boards, Breadboards, Arduino DIY,....

Check Stock

Keywish Scratch Starter Kit,Super Base Sensor Modules Kit Based on Arduino UNO R3 ATmega328P with 30 Lessons Tutorial Compatible with Arduino IDE Mixly Mblock Graphical Programming

✔ High-quality kit: Contains 48 electronic components Kits for Arduino,which fully meet the components required by beginners.All of the Components, breadboard and Integrated Circuits are individually packaged and labeled, and packing in a plastic box.Instruction Link：https://github.com/keywish/keywish-uno-starter-kit.
✔ Graphics programming: Support scratch 3.5, MagicBlock based on Arduino platform, easy to learn and improve writing efficiency..
✔ Strong compatibility: 100% compatible with Arduino UNO R3, NANO,for Arduino IDE, Mixly and Mblock..
✔ Free video tutorial: Comes with tutorial. Free 30 Lessons PDF tutorial from Official website download or you can contact our customer service..
✔ Different gifts: Exquisitely packaged. This is the perfect starter kit for arduino,which as a gift for students, children and friends in the school season, Christmas, New Year, birthday, parties, performances, special occasions, etc..

Check Stock