ReviewsBearing Cup Installer

Honhill 20pcs Crank Bearing Camshaft Oil Seal Remover and Installer Kit Crank Seal Kit Crankshaft and Camshaft Seal Tool Kit

⭐UNIVERSAL COMPABILITY: Camshaft bearing installation tool fits for most oil seals between 27mm and 58mm (1.06’’-2.28’’) in diameter..
⭐MAIN FUNCTION: Want to remove and install the oil seal quickly? Replacing it with the oil seal installer and remover kit saves your time and money without worrying about scraping the crank surface..
⭐STOP THE DAMAGE OF THE CRANK: The blue camshaft oil seal installer tool adapters are made of aluminum, removing and installing crank and cam seals in a breeze, preventing the damage of the crank..
⭐LITTLE USING TIPS: Please kindly note that the thinness of the arm is to fit the crank seal easily. Professional and gentle installation are recommended. Using it with too much strength is not suggested..
⭐DECENT SERVICE: Your purchase fully protected when ordering it today. If you have any concern, please feel free to contact us..

...lity: Made from high-stiffness steel, this kit is built to last with long-lasting durability and resistance to breakage. The powder-coated finish provides a clean surface that is resistant to corrosion and rust..
Excellent Customer Support: This kit comes with a puller, an installer, a docking tool, a support plate, a threaded bolt, a washer, a nut, a pin, and 4 screws, as shown in the picture. We back our product with 24/7 customer service and are always available to assist you with any questions or concerns you may have..

Spicer greaseable universal joint with snap rings.
Bearing Cap Diameter (1): 1.062 inches / Bearing Cap Diameter (2): 1.188 inches.
Bearing Cap to Bearing Cap (1): 3.219 inches / Bearing Cap to Bearing Cap (2): 3.625 inches.
Outside to outside dimension: 3.219 inch.

BENIFITS - Using this installation and removal tool,Changing your wheel bearings become fast and correctly.
USAGE - This kit includes a holder for the rear hub and then a driver to press the old bearing out of the hub. After removal,flip over the hub and....
APPLICATION - Fits the following models and more using hub part number 5136689, 5136690 and wheel bearing part number 3514699 and 3514627:.
2011-18 RZR 900 (All models, front and rear bearings) 2014-18 RZR 1000 (All models including Turbo, front and rear bearings).
INCLUDES - (1) Torpedo Installer Tool (1) Holder.

Includes tools to remove fuel injector sleeves, clean the injector bore and fuel galley, and install injector sleeve cups.
With the head removed, the slide hammer adapter can be installed to pull the injector.
Brush set properly cleans the injector bore which is required for the fuel injector sleeve cup installer to properly seat the cup.
Applications include: 2006-2009 4. 5L Diesel, 2004-2010 6. 0L Diesel.

...pters, pusher washers, receiver sleeves, nut-bolt, heavy duty bearing and portable plastic box..
【PREMIUM SUPPORT】-- Our focus on products and customer services is 2nd to none. If you're not 100% satisfied with this 27213 Master Wheel Hub & Bearing Remover and Installer Tool Kit simply return it for a full refund in 30 days, no questions asked money back guarantee with 12 months’ warranty..

Feature: The three main parts of the compressor clutch assembly are the coil magnet, the pulley, and the clutch plate. The clutch drive plate is splined to the input shaft of the compressor..
Package Included: 1 x Pulley With Bearing.
(Professional Installer is Highly Recommended ).
Pulley Assembly Width:10.4cm,Height:2.8cm.
Part#: 140162C,7511699,10759C,F09OGBC003,5511699,6511699.

EASY TO USE: The bushing puller kit cuts down on frustration and expended energy during difficult wheel bearing, suspension bushing, and seal removal and installation repairs.
WIDE RANGE OF USE: The adapter cups with the bearing puller set provide a wide range of options to fit your exact repair needs.
The OEM Tools bushing driver set includes 20 different size cups for versatile use.
ELIMINATE DAMAGE: The metric bushing driver set reduces the possibility of damaging the bearing/suspension housings.
Don’t have to remove components from vehicles with this bushing tools set.
ADAPTABLE: The bushing installer kit comes with an adapter to use bushings with shop press.
Plates and sleeves can be used in a standard workshop press when on-site access isn’t possible.
MORE USES: The bushing tool set works with silent bearings, hydraulic bearings, ball bearings, shaft seals, rubber bearings, and more.
Cups with bushing press and pull kit allow for hundreds of combinations.

Application : The tool can replace the camshaft needle bearing in Milwaukee Eight Engine. Fit For harley all twin cam..
Includes : Package Include：1* Black steel 8mm cam bearing plate，1* Installer tool，1* Puller tool，4*1/4"-20 Thumb screws..
Function : More adaptable,The collet and fine threaded adopted with special style.Easy install,Design hole can fit the engine..
High quality : Made of high-quality steel materials, our professional technology makes the products more high-quality, durable and rust-free, which provides great convenience for maintenance workers..
100% Satisfaction Guarantee: Providing the best products and services is our goal, if you're not 100% satisfied with your tool, simply return it for a full refund in 30 days, no questions asked money back guarantee with 12 month’s warranty..

Power steering pulley puller and installer kit is used for removing and installing pressed-on alternator ,power steering pump and other pulleys..
The pulley puller and installer kit is compatible with Late GM, Ford & Chrysler Engines,includes special adapters for GM 3.2 Quad 4 engines and Ford Modular engines..
Power steering pump pully puller is made of high carbon steel, long lasting and durable construction for a long service life.The power steering pulley remover and installer set is a must have kit for professional and home DIY mechanics..
The power steering pulley puller/installer equipped with a plastic carrying case, keep all tools well organized, allows for convenient storage and transportation..
We also know the power steering pump pully puller as power steering pulley puller tool,power steering pulley puller set,power steering pump pulley puller tool,power steering pulley remover installer,power steering pump pulley puller/installer,power steering pulley puller kit,power steering puller kit,pulley puller installer kit,pulley installer kit,pulley installer remover,power steering pump puller,and so on..

Tapered Roller Bearing Set (Cup and Cone).
Bearing ID: 1.25” (31.750mm) Cone Width: .6600” (16.764mm) Bearing Width: .6250” (15.875 mm).
Cup OD: 1.7810” / 45.237mm Cup Width: .4750” / 12.065mm.