BOAT MARINE DISPOSABLE IN LINE FUEL FILTER 3/8 SEE THRU CAPSULE
- BOAT MARINE DISPOSABLE IN LINE FUEL FILTER 3/8 SEE THRU CAPSULE.
ReviewsBoat Fuel Line
Autoutfit 6AN 3/8" LS Swap EFI Fuel Injection Hose Line Fitting Kit, Nylon Braided PTFE Fuel Hose 25Ft
- 【Package Included】25Ft 6AN nylon braided PTFE fuel injection line hose*1，6AN PTFE straight hose end*6，6AN PTFE 45 Degree hose end*2，6AN to 3/8" hose adapter fitting*2， AN6 to 3/8"quick disconnect male*1，6AN to 5/16" hose adapter fitting*1..
- 【Premium Material】Nylon braided PTFE fuel line hose and aluminum alloy fittings..
- 【Product Performance】PTFE fuel line with long service life, wear resistance and high temperature resistance. Withstands Operating Temperatures from -76℉ to 446℉ (-60℃ to 230℃). Maximum working pressure: 3000 psi. Bursting pressure: 10000psi. .
- 【Application】This PTFE Fuel line Kit can be worked with petrol, diesel, oil, hydraulic fluid, pump gas, alcohol, E85, coolant, fuel. This kit can be used in EFI LS system, ls engine swap and EFI conversion fuel line, turbo oil feed and boost line, transmission oil cooler line, carb fuel line, fuel return line, vapor return line, vacuum line, fuel supply line and turbocharger fuel line..
- 【Installation recommended】 PTFE hose relatively hard, it can't be bend and folding in h....
NEXADD Fuel Line Pliers Set 4Pcs | Hose Remover Pliers | 9 Inch Fuel Filter Caliper | Hose Pipe Clamp Clip | 80 Degree Disconnect Pliers Set for Auto Maintenance with Storage Case
- NexADD 4Pcs Fuel Line Pliers Set Does It All★- Eliminate the problems associated with removing fuel line connectors or undo fuel lines.This set includes 4 Pcs fuel line hose pliers,a hose remover pliers, a 9'' fuel filter caliper, a hose pipe clamp clip and 80 degree disconnect pliers . You’ll save about 30 percent when you buy NexADD fuel line pliers combo kits instead of buying each tool . Just Add to Cart!.
- Hose Remover Pliers★-The best tool for removing hose clamps for fuel and small water hoses.To remove hoses from transmission,rubber hoses connect to cooler lines. Even if can't fit both sides (hose/tube)between fitting and hose.Slide one side in and work hose out then get both sides in, give handles a squeeze and Voila" off comes hose.Hose remover pliers easily remove stubborn hoses on tanks, radiators, pumps, air cleaners,etc.Remove fuel vacuum or heater hoses from 5/32”to 1/2”(4mm to 14mm)..
- Fuel Line Clip Removal Pliers ★-The fuel line clip removal pliers suitable for removal and replacement of connections on fuel filter lines (petrol & diesel).Required when removing and replacing fuel filters.Upgarded maximum openin....
LTI Universal 10ft Nylon Stainless Steel Braided 5/8\ AN10 PTFE E85 Fuel Line Hose Injection (BLACK, 10AN)
- This PTFE Nylon Braided Fuel Hose are specially designed to work in any automotive project. this hose is ideal for high temperature, high pressure, and offers wide range of fluid compatibility..
- PTFE Nylon Braided fuel line can be used as fuel injection hose, turbo oil feed and boost line, transmission oil cooler line, EFI fuel line, carb fuel line, ls engine swap fuel line, fuel return line, vapor return line, vacuum line, fuel supply line and other high temperature high pressure applications..
- Application: fuel, lube, alcohol, ethanol, coolant and air for automobiles or marine engines, most suitable for racing cars & motor racing bikes. Working temperature range: -76℉ to 446℉ (-60℃ to 230℃). Pressure Rating: Maximum Working Pressure (psi): 2000 psi. Bursting Pressure (psi): 6000psi..
- This hose is made of high-quality PTFE on the inside that gives them high chemical and heat resistance, along with a braided Black Nylon outside which gives them high durability, extreme pressure resistance, and Professional installation is highly recommended..
- 10AN PTFE E85 Fuel Hose Length: 10ft. Inner Diameter: 0.5" (12.95mm). Outside Diameter: 0.62" (16mm) . Please measure before purchase! Fit for AN PTFE hose end fitting ONLY..
Portable Boat Fuel Tank 24L 6 Gallon Marine Outboard Motor Fueling Tank Plastic Tank Compatible with Kayaks, Small/Large Boats, Inflatables and Canoes (6 Gal Fuel Tank)
- 【High Quality Material】This boat fuel tank is made of high density polyethylene, low permeability, anti-aging, impact resistance, won't rust, crack or chip, it can naturally rebound without permanent deformation after encountering an impact..
- 【Portable Design】 The three-dimensional texture surface not only increases the aesthetics of the gas can, but also optimizes the feeling of holding a hand, making the force is even and the hand is not restrained. Equipped with an I-shaped lifting handle, which is more ergonomic, convenient and fast, easy to carry and store..
- 【Easy to Fill】Portable boat gas tank features a fine mesh input spout, so you can fill this portable marine fuel tank without worrying about gunk and grime getting in the gasoline..
- 【Convenient Design】The outboard boat motor fuel tank cap has two function, Sealing and Venting. In addition there are separate air inlet and oil outlet, design for prevent oil from spilling. Marine portable fuel tank includes handle to easily carry fuel wherever you need it..
- 【Wide Application】Fuel tank size: 11.8*....
New All Balls Fuel Pump Module 47-1029 Compatible With/Replacement For Can-Am Outlander DPS 450 EFI, Outlander DPS 570 EFI 2016-2020, Outlander L 450 EFI 2015-2016, Outlander L 500 EFI 2015
- ➰APPLICATION- All fuel, lube, alcohol, ethanol, coolant and gas for automotive and marine. Black braided PTFE fuel line can be used as fuel injection hose, turbo oil feed and boost line, transmission oil cooler line, EFI fuel line, carb fuel line, ls engine swap fuel line, fuel return line, vapor return line, vacuum line, fuel supply line and other high-temperature and high-pressure applications..
- ➰WORKING ENVIRONMENT-Maximum Working Pressure=725 psi(5 mpa). Bursting Pressure=2175psi(15 mpa). Working Temperature Range=-40℉ to 392℉(-40℃ to 200℃)..
- ➰SIZE- length=20 feet. Inner diameter=0.51 inches (12.95 mm). Outer diameter=0.63 inches (16 mm)..
- ➰MATERIAL- Inner layer: PTFE (Teflon) rubber.
- middle layer: 304 stainless steel wire mesh sleeve.
- outer layer: braided nylon. PTFE fuel lines are more resistant to high temperature and pressure..
- ➰NOTE- PTFE hoses are relatively hard and cannot be bent or folded in half.Double check the hose size before ordering.Professional installation is highly recommended..
Wetenex 1/4 Inch Fuel Line 6mm ID Fuel Line-5 Feet with 1/4 Fuel Filter + Fuel Line Clamps + Fuel Shut off Valve Switch
- Fuel line: high temperature resistance, good corrosion resistance, long service life.
- Fuel filter, 180 degree valve and clamp are fit for fuel line.
- Package include: 5 feet fuel line, 2 fuel filter, 12 clamp, 2 fuel Shut off Valve.
EVIL ENERGY 6AN Fuel Line Kit, -6 Nylon Braided Fuel Line Hose Fitting Kit CPE 20FT Black(0.34inch ID)
- 6an braided fuel line kit widely used as transmission oil cooler line, fuel return line, fuel supply line, coolant fluid hose, fuel gauges line, vacuum line, turbo cooler line, oil feed line..
- Nylon and stainless steel braided fuel hose kit can be compatible with transmission fluid, oil, race gas, vacuum, hydraulic fluid, diesel and fuel..
- Maximum Working Pressure: 500psi. Bursting Pressure: 2000psi. Temperature Range: -40℉ to 257℉..
- Package includes: 10pcs 6an swivel hose ends (4pcs straight, 2pcs 45degree, 2pcs 90degree, 2pcs 180degree), 2pcs 6an hose separator clamp and 6an braided fuel line (Length: 20 Feet). Hose ID: 0.34". Hose OD: 0.543inch..
- EVIL ENERGY provide this product 3-month warranty. Any problem you might have, please feel free to contact us via Amazon message..
OUFKAR 6pcs Fuel Line Disconnect Tool Compatible with Ford GM Mazda, Automotive AC Fuel Line Removal Tool Line Removal Tool Kit 5/16-7/8in
- Function of Fuel Line Disconnect Tool: Master Deluxe AC line disconnect tool Fuel disconnect tool kit offers a wide range of tool sizes to separate oil / fuel lines, quick disconnects on heater lines and AC cooling lines,and it exactly the product needed for fuel filter replacement..
- The Fuel Line Disconnect Tool is widely used:Compatible for most Ford, G.M, Mazd.a, and other vehicles with automatic transmission lines, strong compatibility.A must have tool if you work on vehicles.This product definitely made removing the gas lines off easier.
- The Usability and Design of Fuel Line Disconnect Tool: Each refueling tool is color-coded by size for easy identification.
- six sizes 1/2"-12.7mm (Yellow), 3/4"-19mm (Black), 3/8"-9.5mm (Blue), 5/8"-16mm (Green), 7/8"-22.2mm (Red), 5/16"-8mm (Copper), They are nicely colored so you can see what size they are if you're in a tight spot..
- Exquisite Workmanship of Fuel Line Disconnect Tool: Each fuel line quick disconnect heater hose disconnect tool is made of hard plastic with high strength and long life, which can prevent rust and corrosion..
- Easy to Use of Fuel Line Disconnect Tool: Fuel Line Disconnect spring end and unique offset design can enter the narrow or blocked area that is difficult to reach, and quickly sep....
EVIL ENERGY 6AN PTFE E85 Fuel Line Hose Nylon Braided 10FT Black(5/16 Inch ID)
- ID: 5/16". OD: 0.465inch.Length: 10 feet. Please measure before purchase!.
- PTFE fuel line can be used as fuel injection hose, boost line,carb fuel line, ls engine swap fuel line, fuel return line, vapor return line,fuel supply line, etc..
- Working Temperature Range: -76℉ to 446℉ (-60℃ to 230℃). Max Working Pressure: 3000 psi. Bursting Pressure: 10000psi..
- Applicable Medium: all automotive fuels, lubricants, and coolants..
- PTFE hose relatively hard, it can't be bend and folding in half. Professional installation is highly recommended..
EVIL ENERGY 8AN PTFE E85 Fuel Line Hose Nylon Braided 20FT Black(0.394 Inch ID)
- ID: 13/32". OD: 0.543inch.Length: 20 feet(6M). Please measure before purchase!.
- PTFE fuel line can be used as fuel injection hose, boost line, carb fuel line, ls engine swap fuel line, fuel return line, vapor return line, fuel supply line, etc..
- Working Temperature Range: -76℉ to 446℉ (-60℃ to 230℃). Max Working Pressure: 2500 psi. Bursting Pressure: 8000psi..
- Applicable Medium: all automotive fuels, lubricants, and coolants..
- PTFE hose relatively hard, it can't be bend and folding in half. Professional installation is highly recommended..