ReviewsBrazed Carbide Reamers

Outdoor Power Deals Carbide Chainsaw Saw Chain 20\ 3/8\ 33R-72 050 for Some Stihl MS290 MS291 MS311 MS390

  • 3/8 pitch 0.050 gauge - 72 Drive Link - Semi Chisel Type Chain - Very Aggressive Teeth.
  • Solid carbide tipped chain is brazed to case hardened saw chain for the ultimate in life and cutting ability. Designed for woodcutting keep it up and out of the dirt and avoid hitting solid objects this can break or chip the carbide tooth.
  • ( READ ) MS290 and MS291 can have .325 pitch and this will not fit. Buyer is responsible for verify what pitch chain your saw has.
  • Also NOTE Correct use you must allow the chain to cool back to ambient temperature between uses the teeth with break off if you stop using the chain for any amount of time and then pick it up and start going again. Allow chain to cool a minimum of 3 hours.
Check Stock

BOSCH RCB8DG 1-Piece 9 In. Grit 50 TPI Diamond for Cast Iron and Block Reciprocating Saw Blade

  • Diamond Grit cutting edge for cutting cinder block, brick, cast iron, pipe and other abrasive materials..
  • Up to 3-times faster and 3-times longer life than carbide grit blades.
  • Vacuum brazed diamond grit blade for heavy use.
Check Stock

29/32\ Expansion Reamer, Carbide Tipped, Straight Shank, Partial Flute Carbide 56018P, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • 1 1/2 " flute length, Partial Flute Length Carbide.
  • 3/4 " shank diameter, For Reaming abrasive material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

15/16\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56069P, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • 1 1/2 " flute length, Partial Flute Length Carbide.
  • Morse taper shank #3, For Reaming Abrasive Material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

29/32\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56068P, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • 1 1/2 " flute length, Partial Flute Length Carbide.
  • Morse taper shank #2, For Reaming Abrasive Material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

13/16\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56065P, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • 1 3/8 " flute length, Partial Flute Length Carbide.
  • Morse taper shank #2, For Reaming Abrasive Material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

1 3/16\ Expansion Reamer, Carbide Tipped, Straight Shank, Partial Flute Carbide 56026P, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • 1 3/4 " flute length, Partial Flute Length Carbide.
  • 1" shank diameter, For Reaming abrasive material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

1 7/16\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56080P, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • 2" flute length, Partial Flute Length Carbide.
  • Morse taper shank #4, For Reaming Abrasive Material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

1 5/16\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56078P, USA Made

  • When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
  • 1 7/8 " flute length, Partial Flute Length Carbide.
  • Morse taper shank #4, For Reaming Abrasive Material.
  • This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
Check Stock

F&D Tool Company 29321 Shell Reamer Carbide Tipped Spiral Flute, 2\ Diameter, 1\ Hole Diameter, 8\ Fits Arbor, 10 Number of Fits, 2 3/4\ Fit, 1 1/8\ Carb, 3 1/2\ Overall Length

  • Shell Reamers - Carbide Tipped - Spiral Flute.
  • Dia: 2 Hole Dia: 1 Fits Arbor: 8 Number of fits: 10 Fit: 2 3/4 Carb: 1 1/8 Overall: 3 1/2.
Check Stock

F&D Tool Company 29310 Shell Reamer Carbide Tipped Spiral Flute, 1 15/16\ Diameter, 3/4\ Hole Diameter, 7\ Fits Arbor, 8 Number of Fits, 2 1/4\ Fit, 1 1/8\ Carb, 3\ Overall Length

  • Shell Reamers - Carbide Tipped - Spiral Flute.
  • Dia: 1 15/16 Hole Dia: 3/4 Fits Arbor: 7 Number of fits: 8 Fit: 2 1/4 Carb: 1 1/8 Overall: 3.
Check Stock