ReviewsBussmann Relay Block

Wireless Z-Wave Multi-Input/Output Dry Contact Bridge Cert ID ZC08-16040002

BEFORE YOU BUY: Check to make sure your home automation controller / security panel is interoperable with our device. NOT ALL Z-wave Controllers are....
One 24VDC / 110 VAC Relay to control any low voltage device via Z-wave. Controls garage doors, motorized shades, gates, solenoid valves, etc. Relay....
One SIGNAL Input terminal block to receive low voltage (digital, analog, or pulse) signals via Z-wave. Use with reed sensors, contact sensors, door....
9V AC power adaptor included. Low voltage wire is NOT included.
Please visit our website and youtube page for application details and how-to video's. Wiring diagrams are also downloadable on our website product....

OMRON G2R-1-E industrial power relays, switching current up to 16A at 250VAC (or 30VDC), and easy to replace pluggable relays..
LED indicator for each relay channel , relay coil protection by means of a freewheeling diode..
High quality screw terminal block, FR-4 fiber glass PCB, dual copper layers..
Panel mount or DIN rail mount versions are available. Taiwan DINKLE fireproof nylon material DIN rail mount carrier (not China low quality carrier), can support width 35mm / 32mm / 15mm rail, and the carrier can be taken apart for panel mount use..

One 40A and three 20A outputs, for a combined total of 100A continuous..
Each output has a thermal overload, and short circuit protection along with LED status indicators for the Thermal/Overload, Active/Inactive status..

Rated to 240 Amps with a 1/4-20 Input Stud on a Nickel-Plated Bus Bar with 12 #8-32 Stainless Steel Terminal Screws.
3/16" Mounting Holes on Each Side of Terminal Block.
Includes 12 Premium Double Crimp Nylon Insulated Ring Terminals.
Includes Hard Protective Cover (Red) and Flexible Stud Terminal Boot (Red).
Use with Fastronix Relay Panel (#900-004) and LED Fuse Panel (#500-043) for Professional, Protected Circuits.

Kit includes Relay Buddy tester, 5 new relay adapters and blow mold case.
Relay Buddy is a quick go/no go tester for the most common automotive relays.
With the included adapters, Relay Buddy now tests 5 different relay types and also tests shielded relays.
Relay Buddy will fail the relay and light the red LED if any of the test cycle proves unsuccessful during the test session.
Settable to 4 and 5-pin relay and uses vehicle's 12 volts battery for power.

Able to test an entire circuit - from battery to component, including the relay With this item the technician can jump a relay.
do an AC charge from the relay by activating the compressor.
do compression testing by activating the starter relay and even check turn signals or lights from the front of the car.
Allows the technician to diagnose the problem without the use of a multimeter.
The lighted display shows the technician the problem immediately.
With this item the technician can jump a relay.
Includes: (1) Tester, (6) popular Relay Leads, and (1) Universal Relay Lead.

Output: fan relay, alarm relay and 4-20ma current loop.
Controls: buzzer, Digital display, latching relay, relay Delay, relay minimum runtime.
Mounts on a standard 4” x 4” electrical box.
5 a spdt fan relay controls starters of exhaust fans.

NOYITO 2-Channel Micro USB Relay Module is equipped with a stable USB to serial port chip and a microcontroller. It can use the serial port debugging software to send serial commands on the computer to control the opening and closing of the 2-channel relay..
Onboard high performance microcontroller chip, CH340 USB control chip.With power LED indicator and relay status LED.On-board 2-channel 5V, 10A/250VAC, 10A/30VDC relay, long relay life, can work 100,000 times continuously..
Module with overcurrent protection and relay diode freewheel protection..
NOYITO 8-Channel Micro USB Relay Module ASIN：B09RGTSHHW.
NOYITO 4-Channel Micro USB Relay Module ASIN：B09RGVQXXT.

Inexpensive protection for an electric fan and a vehicle's wire harness.
Provides constant voltage, protects from voltage and amperage spikes and prevents the fan from back feeding voltage.
Threaded thermostatic switch (185°F On/175°F Off) screws into the engine block or intake manifold.
Switch thread size 3/8"-18NPT (1/2" to 3/8" NPT adapter provided).
Protected by 40-amp relay and 30-amp circuit breaker.