ReviewsButt Welding Ball Valve

ATPEAM Butt Welding Clamp | Pack of 16 Small Welding Clamps Auto Body Panel Clamps for Edge to Edge Welding

  • Premium Material: Panel welding clamps are constructed of zinc-plated steel to ensure maximum durability and strength while resisting rust.
  • Fits your Project: Each welding square tool pipe clamp can extend the clamp block to provide a .4-inch (1cm) tall gap.
  • Fits 3/16-inch to 26 gauge sheet metal materials.
  • Good performance: These small welding clips can be completely fixed before butt welding, leaving only a small gap to make the weld completely penetrate. This is an ideal choice for professionals engaged in sheet metal body repair..
  • Easy to Use: Loosen the winged nut from the alignment screw then wedge two panels across from each other between the square body and the clamp block.
  • Tighten the winged nut to ensure a secure hold.
  • Use all 16 clamps for larger projects, then joint weld between them.
  • Package Included: Welding accessories set includes 16 welding corner square welder clamps.
  • Used to make precision butt welds and edge-to-edge welds for patch repairs in floors, wings, door skins, fabricating, and re-skinning projects.
Check Stock

3/8 Electric Solenoid Valve 12-VDC VITON Gasket Air Gas Fuel Normally Closed

  • -NEW- Re-engineered low power coil with up to 50% less heat generation. The valve starts as 19W and as it heat up to operating temperature power reduces to approx. 10-13W..
  • Constructed of industrial grade brass, this valve is corrosion resistant, more conducive for welding, optimal for higher temperature projects, and can be used with gasoline, diesel fuel, kerosene oil, natural gas, air etc. Due to the chemical composition of brass, this valve should NOT be used with projects involving drinking water or other water projects..
  • This valve was manufactured with a VITON seal. VITON is the most durable and high performance rubber material with the ability to resist high temperatures and corrosive chemicals and other fluids like gasoline, diesel fuel, oils, and lubricants..
  • This highly responsive valve will open and close in less than 1 second when actuated.
  • meaning it will open or close the flow instantaneously when energized or de-energized. Also, our U.S. SOLID engineers have determined that the life cycle of this valve is well over a million cycles with proper operating conditions and maintenance..
  • PLEASE NOTE: This valve is NOT a continuous duty valve and should NOT be in continuous use for more than 8 hours in a single cycle.
Check Stock

1/2' NPT Brass Electric Solenoid Valve 12V DC Normally Closed VITON from U.S. SOLID

  • Constructed of industrial grade brass, this valve is corrosion resistant, more conducive for welding, optimal for higher temperature projects, and can be used with gasoline, diesel fuel, kerosene oil, natural gas, air etc. Due to the chemical composition of brass, this valve should NOT be used with projects involving drinking water or other water projects..
  • This valve was manufactured with a VITON seal. VITON is the most durable and high performance rubber material with the ability to resist high temperatures and corrosive chemicals and other fluids like gasoline, diesel fuel, oils, and lubricants..
  • This highly responsive valve will open and close in less than 1 second when actuated.
  • meaning it will open or close the flow instantaneously when energized or de-energized. Also, our U.S. SOLID engineers have determined that the life cycle of this valve is well over a million cycles with proper operating conditions and maintenance..
  • PLEASE NOTE: This valve is NOT a continuous duty valve and should NOT be in continuous use for more than 8 hours in a single cycle.
  • to do so will shorten the life of the valve and may cause the core of the valve to burn out. If you need a continuous duty valve for your project please search for our U.S. SOLID Motorized Ball Valve....
Check Stock

3/4 Brass Electric Solenoid Valve 110V AC Normally Closed Water air Diesel by U.S Solid

  • Constructed of industrial grade brass, this valve is corrosion resistant, more conducive for welding, optimal for higher temperature projects, and can be used with gasoline, diesel fuel, kerosene oil, natural gas, air etc. Due to the chemical composition of brass, this valve should NOT be used with projects involving drinking water or other water projects..
  • This valve was manufactured with a VITON seal. VITON is the most durable and high performance rubber material with the ability to resist high temperatures and corrosive chemicals and other fluids like gasoline, diesel fuel, oils, and lubricants..
  • This highly responsive valve will open and close in less than 1 second when actuated.
  • meaning it will open or close the flow instantaneously when energized or de-energized. Also, our U.S. SOLID engineers have determined that the life cycle of this valve is well over a million cycles with proper operating conditions and maintenance..
  • PLEASE NOTE: This valve is NOT a continuous duty valve and should NOT be in continuous use for more than 8 hours in a single cycle.
  • to do so will shorten the life of the valve and may cause the core of the valve to burn out. If you need a continuous duty valve for your project please search for our U.S. SOLID Motorized Ball Valve....
Check Stock

Strong Hand Tools CPL45 , Pipe Fit-Up Clamp, Pipe Welding Alignment Tools (Pipe Diameter Capacity: 2″ ~ 4″ (50~100 mm))

  • A compact, light weight, portable clamp for the quick fit-up of round pipes and flanges for butt welding. Easy-to-use design for the rapid, repeated loading and unloading of work pieces..
  • A compact, light weight, portable clamp for the quick fit-up of round pipes and flanges for butt welding..
  • Easy-to-Use design for the rapid, repeated loading and unloading of workpieces..
Check Stock

Toolly 16 Pack Butt Welding Clamps - Small Welding Clamps Auto Body Panel Clamps for Edge to Edge Welding

  • Butt Welding Clamps includes 16 welding corner square welder clamps.
  • Used to make precision butt welds and edge-to-edge welds for patch repairs in floors, wings, door skins, fabricating, and re-skinning projects.
  • Use the Toolly Welding Square Clamp Set to pinch sheet metal panels level to each other.
  • While these metal clamps hold panels edge to edge with a 1mm gap, you can quickly weld the sheets together.
  • Each welding square tool pipe clamp can extend the clamp block to provide a .4-inch (1cm) tall gap.
  • Fits 3/16-inch to 26 gauge sheet metal materials.
  • Loosen the winged nut from the alignment screw then wedge two panels across from each other between the square body and the clamp block.
  • Tighten the winged nut to ensure a secure hold.
  • Use all 16 clamps for larger projects, then joint weld between them.
Check Stock

Toolly Butt Welding Clamps - Small Welding Clamps Auto Body Panel Clamps for Edge to Edge Welding, Pack of 16 (1 inch x 1 inch x 2.1inch)

  • 【Product Purpose】Butt welding clamps set includes 16 welding corner square welder clamps, which can be used to make precision butt welds and edge-to-edge welds for patch repairs in floors, wings, door skins, fabricating, and re-skinning projects. They are good accessories to help you to find the location quickly in repair work..
  • 【Perfectly Align Panels】Using the Toolly Welding Square Clamp Set to pinch sheet metal panels level to each other.
  • When these metal clamps hold panels edge-to-edge with a gap of 1mm, you can quickly weld the sheets together..
  • 【Applicable Types】Each welding square tool pipe clamp can extend the clamp block to provide a 4-inch (1cm) tall gap.
  • Fits 3/16-inch to 26 gauge sheet metal materials..
  • 【Easy To Use】Loosen the winged nut from the alignment screw and then wedge two panels across from each other between the square body and the clamp block.
  • Tighten the winged nut to make sure a firm fixation.
  • Use all 16 clamps for larger projects, then perform joint welding between them..
  • 【High Quality & Portable】These panel welding clamps are made of high quality matrial, which makes sure the durability and strength.
  • meanwhile, these clamps are in small size can be easily placed in your pocket or welding equipment tool bag..
Check Stock

1/4 NPT Brass Electric Solenoid Valve 12VDC Normally Closed VITON Standard USA Pipe Thread Solid Brass Direct Acting Viton Gasket Solenoid Valve by U.S Solid.

  • Constructed of industrial grade brass, this valve is corrosion resistant, more conducive for welding, optimal for higher temperature projects, and can be used with gasoline, diesel fuel, kerosene oil, natural gas, air etc. Due to the chemical composition of brass, this valve should NOT be used with projects involving drinking water or other water projects..
  • This valve was manufactured with a VITON seal. VITON is the most durable and high performance rubber material with the ability to resist high temperatures and corrosive chemicals and other fluids like gasoline, diesel fuel, oils, and lubricants..
  • This highly responsive valve will open and close in less than 1 second when actuated.
  • meaning it will open or close the flow instantaneously when energized or de-energized. Also, our U.S. SOLID engineers have determined that the life cycle of this valve is well over a million cycles with proper operating conditions and maintenance..
  • PLEASE NOTE: This valve is NOT a continuous duty valve and should NOT be in continuous use for more than 8 hours in a single cycle.
  • to do so will shorten the life of the valve and may cause the core of the valve to burn out. If you need a continuous duty valve for your project please search for our U.S. SOLID Motorized Ball Valve....
Check Stock

Forney 32110 E7014 Welding Rod, 1/8-Inch, 10-Pound

  • All position welding rod with digging arc, deep penetration on dirty, rusty and painted materials.
  • Ideal for joints requiring deep penetration such as square edge butt welds, good for vertical and overhead welding with light slag.
  • Excellent for galvanized steel and rusty/oily steel in maintenance or repair applications, plus pipe welding.
Check Stock

Forney 32005 E7014 Welding Rod, 3/32-Inch, 5-Pound

  • All position welding rod with digging arc, deep penetration on dirty, rusty and painted materials.
  • Ideal for joints requiring deep penetration such as square edge butt welds, good for vertical and overhead welding with light slag.
  • Excellent for galvanized steel and rusty/oily steel in maintenance or repair applications, plus pipe welding.
Check Stock

LGXEnzhuo Manually Operated HDPE Butt Fusion Welding Machine 4 Clamps Pipe Fusion Welder Manual PE PP PB PVDF Pipe Hot Melt Machine 110V 63-160mm

  • 【WIDE APPLIACTION】Manually Operated HDPE butt fusion welding machine is suitable for PE and PP pipes and fittings. High quality design and construction provides an excellent machine for welding both on the worksite and in the factory.
  • 【PARAMETER】Model No.:2.48"-6.30" (63-160mm) 4 clamps.
  • Welding level(Φ, mm)outer dia: 2.48" (63mm), 2.95" (75mm), 3.54" (90mm), 4.33" (110mm), 4.92" (125mm), 5.51" (140mm), 6.30" (160mm).
  • 【FEATURES】Features of manual hot melt butt welding machine: It consists of four parts: frame, milling cutter, independent heating plate, milling cutter and heating plate bracket.
  • 【HIGH QUALITY】The heating plate adopts an independent temperature control system and is coated with PTFE.
  • The main part of the frame is made of aluminum alloy material, which is simple in structure, compact and easy to use.
  • 【EASY TO USE】Electric milling method is adopted, with single ....
Check Stock