ReviewsCamlock Coupling Type A

Chain Coupling Sprocket, Bore 3/4 in

  • For use with specific Martin flange types (J type flanges in the case of JEM and JEMS type sleeves, and all flange types in the case of EM type sleeves) in the Quadra-Flex series flexible coupling assemblies (sold separately).
  • Thermoplastic rubber for resistance to oil and higher temperatures.
  • Three types: one-piece solid (Type JEM), one-piece split (Type JEMS), and two-piece split with a metal retaining ring (Type EM) for applications where the coupled shafts are difficult to separate.
  • Operating temperatures range from -50 to 275 degrees F (-46 to 135 degrees C).
Check Stock

uxcell 3mm to 1/8 inch Bore Rigid Coupling Set Screw L26XD10 Aluminum Alloy,Shaft Coupler Connector,Motor Accessories

  • Connection Diameter: 3mm to 1/8 inch, Total Length: 26mm /1.02 inch, Outside Diameter : 10mm/ 0.39 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold....
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

uxcell 10mm to 10mm Bore Rigid Coupling Set Screw L22XD16 45# Steel,Shaft Coupler Connector,Motor Accessories

  • Connection Diameter: 10mm to 10mm, Total Length: 22mm /0.87 inch, Outside Diameter : 16mm/ 0.63 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

uxcell 8mm to 8mm Bore Rigid Coupling Set Screw L22XD14 45# steel,Shaft Coupler Connector,Motor Accessories

  • Connection Diameter: 8mm to 8mm, Total Length: 22mm /0.87 inch, Outside Diameter : 14mm/ 0.55 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

uxcell 7mm to 7mm Bore Rigid Coupling Set Screw L22XD14 Copper,Shaft Coupler Connector,Motor Accessories

  • Total Length: 22mm/0.87 inch, Outside Diameter : 14mm/0.55 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

uxcell 4mm to 4mm Bore Rigid Coupling Set Screw L26XD10 Aluminum Alloy,Shaft Coupler Connector,Motor Accessories

  • Connection Diameter: 4mm to 4mm, Total Length: 26mm /1.02 inch, Outside Diameter : 10mm/ 0.39 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

Martin 9HS Quadraflex Sleeve, Hytrel, Inch, 6\ OD, 3\ Length

  • For use with specific Martin flange types (J type flanges in the case of JEM and JEMS type sleeves, and all flange types in the case of EM type sleeves) in the Quadra-Flex series flexible coupling assemblies (sold separately).
  • Thermoplastic rubber for resistance to oil and higher temperatures.
  • Three types: one-piece solid (Type JEM), one-piece split (Type JEMS), and two-piece split with a metal retaining ring (Type EM) for applications where the coupled shafts are difficult to separate.
  • Operating temperatures range from -50 to 275 degrees F (-46 to 135 degrees C).
Check Stock

uxcell 5mm to 6mm Bore Rigid Coupling Set Screw L22XD14 Copper,Shaft Coupler Connector,Motor Accessories,2pcs

  • Connection Diameter: 5mm to 6mm, Total Length: 22mm /0.87 inch, Outside Diameter : 14mm/ 0.55 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

uxcell 1/8 inch to 5mm Bore Rigid Coupling Set Screw L26XD10 Aluminum Alloy,Shaft Coupler Connector,Motor Accessories

  • Connection Diameter: 1/8 inch to 5mm, Total Length: 26mm /1.02 inch, Outside Diameter : 10mm/ 0.39 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

uxcell 5mm to 5mm Bore Rigid Coupling Set Screw L25XD14 Aluminum Alloy,Shaft Coupler Connector,Motor Accessories,Blue

  • Connection Diameter: 5mm to 5mm, Total Length: 25mm /0.98 inch, Outside Diameter : 14mm/ 0.55 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

Martin 9JEM Quadraflex Sleeve, Thermoplastic Rubber, Inch, 6\ OD, 3\ Length

  • For use with specific Martin flange types (J type flanges in the case of JEM and JEMS type sleeves, and all flange types in the case of EM type sleeves) in the Quadra-Flex series flexible coupling assemblies (sold separately).
  • Thermoplastic rubber for resistance to oil and higher temperatures.
  • Three types: one-piece solid (Type JEM), one-piece split (Type JEMS), and two-piece split with a metal retaining ring (Type EM) for applications where the coupled shafts are difficult to separate.
  • Operating temperatures range from -50 to 275 degrees F (-46 to 135 degrees C).
Check Stock