ReviewsCenter Cutting

THANOS Cut Off Wheel Cutting Wheel 50 Pack 4-1/2 x3/64 x7/8 Metal&Stainless Steel,Ultra Thin Cutting Disc

【50 PACK】This is for a pack of 50 pieces of our cutting wheels.Each disc is 4.5 inch in diameter with a 7/8" metal center and 0.045" thickness..
【MATERIAL】Proprietary aluminum oxide grain for long life and fast cutting.Cut off Wheel is fully reinforced with 2 bonded sheets of Fiberglass....
【PERFORMANCE】Thin 0.045'' cutting wheel design for fast burr free cutting. Perfectly compatible with all 4-1/2 inch angle grinders with 7/8-inch....
【APPLICATION】Tough abrasive cutting discs are perfect for super-fast, clean cutting in carbon steel, stainless steel, pipe, iron, copper....
【SAFETY】Wear all applicable safety gear when using these discs (eyes/ears/face/hands/body/etc)..

Check Stock

DT-DIATOOL Turbo Mesh Diamond Blade 8 Inch with X Rim Segment for Tile Porcelain Ceramic Fits 7/8 or 1 Inch Arbor

Fits 7/8 inch or 1 inch arbor, Segment thickness 1.8 mm.
Ideal for cutting hard Ceramics, Porcelain, Tile, Granite and other materials.
Thick Reinforced Center Hub for Stable Cutting.
Turbo-mesh rim and core for fast cutting and minimal chipping.

Check Stock

Creative Grids 10in Log Cabin Trim Tool Duo - CGRJAW10

The 10in Log Cabin Trim Tool Duo features exclusive markings to create perfect finished Log Cabin.
or Courthouse Steps blocks up to 10in. But, in this case, there are two sets of markings - one set for 1in finished logs and additional markings for 1/2in finished logs..
Make log cabin blocks with all the same width of strips, or combine the two widths for limitless design potential! After adding each round of logs, place the appropriate centering square on the ruler over the center square of the block and trim..
The cutting instructions for the strip widths and center square are printed right on the tool!.
The ruler slides easily over the fabric until pressure is applied. Then, our exclusive gripper holds the fabric in place while cutting, eliminating slipping and miss-cuts!.

Check Stock

MANTISTOL 13

Design for cutting LVP, WPC, SPC, LVT, VCT, PVC, Vinyl Plank Flooring. Cutting unapproved materials will void warranty..
No dust, No noise, No electricity needed, Easy and Professional cutting vinyl floor, Save time. If you received the cutter that cuts less than 8mm thick, please remove the blade, clean the aluminum shavings in the groove, and then assemble the blade correctly in the center of the blade bar..
Why does the floor you cut crack? Because your floor must be Rigid Core Vinyl Plank SPC or RVP, it is a stone-plastic composite material, which contains stone powder.
it is a brittle material. Floor cracks occur when at least two or more cuts are required to make long cuts and corner cuts..
13" cutting width and 8mm cutting depth. Straight cut, Angle cut.
" L & " cut and Lengthwise cut(Solve the installation of wall and corner).Clearly marked measuring guide. 0-45 Angle Cutting, Translational cutting,the deep of the throat is 115mm/4.5inch.Easy to use and to carry around..
2.2mm thick tungsten steel sharp blade, included a 600 Grit oilstone to keep sharp.When the blade becomes dull. Must repair the sharpness of the blade (installed flooring on about 5000 sq.ft ) Otherwise it will quickly end the service lifeman-made damage is not covered by th....

Check Stock

WORKPRO 14-Inch Bolt Cutter, Tri-Material Handle with Comfort Grip, Chrome Molybdenum Steel Blade, for Rods, Bolts, Rivets, Wires, Cables and Chains

WORKPRO 14-inch Bolt Cutter: Your handy tool to handle a variety of cutting jobs with ease. Cutting Capacity: HRC≤42: 7/32-inch(5mm Maximum).
HRC003c25: 1/4-inch(6mm Maximum) Note: Cutting locks is not recommended.
Strong & Durable Construction: Drop forged chrome molybdenum steel jaw with sandblasting treatment for long life. Hardened center-cut blades with HRC56-60 hardness deliver superior cutting performance..
Ergonomic Design: Tubular steel handles for maximum leverage, with anti-slip soft tri-material rubber grips offering comfort and control during extended use..
Compound Action: By combining handles with hinges that transfer power to the jaw and cutting blades, compound cutting action generates more cutting force to cut through hard materials..
Extensive Uses: This heavy duty bolt cutter is ideal for cutting rods, bolts, rivets, wires, cables and chains..

Check Stock

4.5Inch Super Thin Diamond Tile Blade for Cutting Porcelain Tiles Marbles…

Super thin turbo mesh rim diamond blade provide fast, precise, smooth and chip-free cutting experience for you..
Thicker center to avoid vibrations and wobbling. High Performance diamond matrix provides long life and enhanced material removal..
Diamond blade can be used as porcelain tile blade, ceramia tile blade, granite blade and other thin masonry blade..

Check Stock

BHA Metal and Stainless Steel Depressed Center Cut Off Wheels for Angle Grinders 4.5” x .045” x 7/8” - 25 Pack

25 Pack Depressed Center Metal Cutting Discs.
High Performance 4.5" Depressed Cut Off Wheel.
Ultra-thin design for minimal material loss.
Proprietary aluminum oxide grain for agressive cutting action.

Check Stock

25 Pack 4.5 Inch Cutoff Wheels for Metal Premium Materials Stainless Steel Cutting Wheel,Thin Cut-Off Discs for Angle Grinder by Panlen 25

Premium and Value Materials - Panlen cutting discs are made of aluminum oxide grains that are durable and safe. It also provides aggressive cutting....
Longest Lasting - Cutting wheels metal center and 0.045" thickness,provide the best balanced Cut Life, Cut Rate, Cut Precision,allowing you to cut....
Perfect Size - Outer diameter:4 1/2 inch inside diameter:7/8 inch, operating up to 13,300 RPM. fit for most angle grinders, such as Dewalt Makita....
Multiple Applications - Tough abrasive cutting discs are perfect for super-fast, clean cutting in carbon steel, stainless steel, pipe, iron, copper....
Package and Safety - 25 pieces. Please use all necessary protective gear when you use these cutting discs..

Check Stock

7 Inch Super Thin Diamond Tile Blade Porcelain Cutting Blade, Dry or Wet Cutting Ceramic Granite Marble

【SPECIFICATIONS 】: Diameter: 7 Inch(180mm).
Thickness: 0.06 Inch(1.6mm), Up to 8,600 maximum RPM. This diamond blade fits for most tile saws and handheld angle grinders..
【Super thin turbo mesh design 】 : Super thin turbo mesh rim diamond blade can provide you with a fast, precise, smooth and chip-free cutting experience. Thicker center to avoid vibrations and wobbling..
【Work efficiently】: The tile blade is suitable for wet and dry cutting, and wet cutting effect is better, can extend the service life of saw blades, X mesh turbo wave is conducive to cooling and provides high-efficiency cutting efficiency..
【Material】: The diamond cutting wheel is made of high quality diamond, impact-resistant and high-temperature resistant..
【Widely Application】: Our grinder blade are specially designed for cutting porcelain, brick, ceramic tile, granite, sandstone quartz, marble, , slate, cement backer board..

Check Stock

Alumicolor Aluminum Straight Edge with Center Finding Back, 42IN, Silver

HIGH-QUALITY ALUMINUM STRAIGHT EDGE - this measuring tool is a ruler and drafting tool that is 42 Inches in length.
QUICK AND EASY CENTER MEASUREMENTS – Save time and effort calculating the exact center of 2 points with this handy tool. Perfect for crafting, framing, embroidery, drawing, drafting and even rotary woodworking using salvaged lumber.
SILVER STRAIGHT EDGE RULER AND MEASURING TOOL - high-quality silver extruded aluminum is imprinted using photo anodizing process that makes for a uniform finish and color, through this process calibrations become a permanent part of the aluminum and will not wear off over time.
DURABLE CONSTRUCTION WITH ULTRA-SMOOTH EDGES - high-quality constructions makes this measuring and cutting tool perfect for inking lines and cutting against, extruded aluminum is much more rigid than thin steel versions.
ALUMICOLOR IS QUALITY - made with the highest quality extruded aluminum all straight edge measuring tools and rulers have smooth edges and are calibrated to exact specifications.

Check Stock

Accusize Industrial Tools MT3 Precision Medium Duty Live Center, Overall Length 6.69'', 0537-6437

Precision Medium Duty Live Center For General Purpose On Manual Engine Lathe.
The live center has a combination of deep groove ball bearing, thrust ball bearing and needle bearing..
The anti-dust seal can prevent cutting fluid and dust from entering into the center bearing.
The 60° rotating spindle is made from carbon alloy steel with heat treatment to HRC 58±2 for high rigidity and wears resistance.

Check Stock