3000 psi Pressure Washer Pump for Excell Devilbiss XC2800 XR2750 XR2750-01 New
BRAND NEW OEM PRESSURE WASHER PUMP FOR 2800-3000 PSI UNITS.
Specs:2800-3000 PSI / 2.4 GPM – MAX 2.5 GPM FACTORY RATING, BRASS HEAD PUMP, INCLUDES THERMAL RELEASE VALVE, Chemical Injector. FITS 3/4″ SHAFT HOLE DISTANCES ARE 2 5/8″ CENTER TO CENTER ON OUTER HOLES / 1 7/8″ FROM CENTER SHAFT HOLE TO EACH OUTER HOLE..
**Fits Honda Excell units with 3/4″ shaft only!!! Some Excell units have the 7/8″ shaft and this pump will not work!**.
UNIVERSAL PUMP – FITS MANY MAKES AND MODELS! INCLUDES THERMAL RELEASE VALVE.
The ROP Shop | 2400 PSI Power Pressure Washer Water Pump for Excell & Devilbiss VR2400, VR2500
... 3/16” x 6 7/16” & 4" Center to Each Outer Hole. Maximum Water Temperature: 140° F. Inlet Connection Type: Standard Garden Hose. Outlet Tube Connection: 22mm Male. Refer to images 2 and 3 for more information.
Includes - (1) Vertical Pressure Washer Pump with Chemical Injector, Unloader Valve, Thermal Release Valve & Outlet Tube (come installed).
This pump is for vertical gas engine driven units. In some instances, the pump may need to be removed to change engine oil. The mounting flange provides a convenient connection to most 7/8” diameter shaft vertical gas engines in 4.5-7 HP. The pump has a hole in the leg for draining the engine oil. The pump includes a built-in pressure control valve, downstream chemical injection system and thermal relief valve.
This has the outlet facing the front. Some specific pressure washers may require longer bolts and spacers to mount the pump to your engine. These bolts and spacers are NOT included, but may be purchased at your local hardware store. Common bolt sizes: Two - 5/16" 18 x 2 1/2", One - 5/16" 18 x 3 1/2".
2800 psi 2.5 gpm Universal Power Pressure Washer Water Pump 308653052 for Homelite.
Specs - Maximum Pressure: 2800 PSI. Maximum Flow: 2.3 GPM. Maximum Pump Speed: 3400 RPM. Shaft Diameter: 7/8" Shaft. 3 Bolt Pattern: 7 11/16” x 6....
Includes - (1) Vertical Pressure Washer Pump with Chemical Injector, Unloader Valve, Thermal Release Valve & Outlet Tube.
This pump mounts vertical and is a rear facing (water inlets/outlets come out of the rear of the engine). Pump needs at least 5.5HP to handle PSI.....
This pump may require 1/2" spacers when installed, depending on motor configuration. Spacers are used in the case that the pump arm(s) hits the engine....
Actron's Fuel Pressure Tester Kit works on most domestic fuel injected vehicles having a Schrader valve test port on the fuel rail.
Use on the following: Ford high pressure central fuel injection and GM, Ford, and Chrysler multi-port fuel injection - multi-port means one fuel injector per cylinder.
Tests: fuel pump check valves (leak down test), fuel pressure regulators, weak fuel pumps, fuel line integrity (clogged or damaged fuel filters), leaking injectors.
Kit includes: large easy-to-read 2-1/2 inch gauge with standard (0-100 psi) and metric (0-700kPa) scales, Ford fuel line adapter, solid brass fittings, & pressure relief valve for safe, clean testing.
AEM (30-3302) V2 Water/Methanol Injection Kit with Internal MAP Sensor
Boost Dependent controller features on-board MAP sensor with large adjustment knobs, integrated plug for harness connection, integrated fuse, covered status light and test button for enhanced splash resistance and mounting tabs.
Wiring harness is terminated with a positive-lock connector on one end with color-coded wires to ease installation, power and ground wires for the pump and additional wire for optional on/off fluid solenoid.
Pump does not cycle on/off and provides quiet, smooth operation.
it features robust construction including integral hose fittings, EPDM seals and a Santoprene diaphragm that provides consistent and reliable fluid delivery.
Precision-machined billet-aluminum injector with integral check valve.
three interchangeable injector nozzles to cover a wide variety of HP levels (250cc/min, 500cc/min and 1,000cc/min).
tank-less 35 PSI Boost dependent gas water/methanol system.