ReviewsCurrent Isolation

Baomain SSR-60DA 60A Solid State Relay Module 4-32VDC / 24-480VAC + Heat Sink

Photocoupler isolation between input control signal and controlled power, isolation surge voltage up to 7500V..
Input signal turn-on voltage DC 3 to 32V, turn-off voltage DC 0 to 0.8V. LED indication for relay turn-on..
Output voltage range: AC 90 to 250V(50/60Hz). Maximum on-state average current 3 Amp. Maximum on-state current 10 Amp (003c 10 seconds). Non repetitive surge peak on-state current: 120 Amp (003c20mS). Load type: General purpose..
This is a simple and practical solid state relay module, which is very convenient to use, for Arduino, Raspberry Pi, ESP32, PLC or other projects. The GPIO of these controllers are directly connected to this relay input to control the mains power, and it is suitable for most loads less than 350 Watts (for 115VAC)/700 Watts (for 230VAC)..
Compact ABS plastic case and wires connect for easy mount. Two screw mounting holes are convenient for you to fix it on the wall or wooden board. Of course, you can also choose not to lock the screw..

This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
Wide Application These 12V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine etc..

USB isolator:This USB isolator protect the communication interface between the host, such as a PC, and its peripheral.Through this isolator, the....
Maximum support 12Mbps:Support USB full speed 12 Mbps or low speed 1.5 Mbps . Please note: this USB isolator does not support 480 Mbps,So please don't....
Industrial grade: Built-in ADI ADUM3160 chip, support iCoupler technology. Signal isolation: 2500V.
Compatibility: This USB isolation adapter is compatible with Windows 7, 8, 10 and various Linux OS and Mac OS.
Warranty:DSD TECH provide a 1 year warranty and lifetime technical support for this USB isolator.if you have any questions, please feel free to....

【H-bridge Driver Module】The drive uses a full H-bridge driver module full-bridge MOSFET driver chip and composed with very low internal resistance and high current. MOSFET H-bridge driver circuit, with strong drive and braking effect, signal isolation chip isolates motor drive effectively..
【Effective Protection】With the microcontroller PWM signal isolation, effectively protect microcontroller..
【Input Maximum】To achieve the motor forward and reverse rotation, two PWM input maximum 200kHz frequency..
【Fully Compatible】Power indicator is schematically clear. The power supply voltage 5V to 15V. 3.3V to 12V, PWM level is fully compatible. High current 50A..
【Warm Tips】Ffor your safety and protection of use, our product is tested to ensure trouble-free installation and performance, please rest assured to buy..

Current sensing relay for monitoring electrical current.
Current carrying wire is routed through an aperture.
Electrical isolation between circuits (SPDT).
Internal transformer for scaling the current and a voltage reference circuit for a repeatable trip point.
UL Recognized for safety and RoHS compliant for hazardous substances.

Type: single phase transformer and output capacity: 96 va.
Primary rating voltage: 117V and secondary rating voltage: p1=12v, p2=24v.
Secondary rating current: p1=4a, p2=4a and frequency: 50/60Hz.
Time rating: continuous and isolation resistance: above 500Vdc 100mω.
Isolation strength: 1500Vac 50Hz p-s in 1 minute and temperature rise: under 70 degree resisting method.

Price For: Each No. of Channels: 1 Isolation Voltage: 3.75kV Optocoupler Output Type: Analog Input Current: 16mA Output Voltage: 3.8V Opto Case Style: DIP No. of Pins: 8 Bandwidth: 100kHz Forward Current If: 5µA RoHS Compliant: Yes.

➤【DC12-32V】- This isolation module need two complete independent DC12-32V power supply..
➤【Main function】- Main function is input 0-10V analog voltage signal,after isolation, output 0-10V analog voltage signal..
➤【Scope of Application】- Used to isolate high voltage or strong interference voltage or current (voltage) signal then transferred to PLC or controller MCU, isolating controlling end and controlled end, to assure stability and anti-interference ability of system..
➤【Use】- It will has better performance if install this module and controller in a metal box and box is grounded..
➤【Note】- The potentiometer is used to amend corresponding relation of output voltage. Output voltage can be fine adjusted and calibrated, normally it has already been calibrated..