ReviewsCurrent Relay

DC Current Switch,Current Sensing Relay DC Current Sensing Switch 0-300A Amp Sensor Monitoring Relay D366

  • Basic Function:When the piercing current exceeds the set value, the output switch will act Automatically reset when the piercing current is less than the set value..
  • Set threshold: set the threshold when the perforation current exceeds the threshold, the relay will work, and when the perforation current is lower than the threshold, the relay will reset.
  • Indicator light: the indicator light is off when there is no current, the green light is on when the current is lower than the threshold, and the red light is on when the current is higher than the threshold.
  • Delay adjustment: power-off delay can be set from 0 to 99 seconds, clockwise to increase and counter-clockwise to decrease.
  • Detection range: 0-50A, [email protected] AC/DC contact capacity.
Check Stock

Inkbird SSR Solid State Relay SSR 40DA for PID Thermostat Temperature Controller

  • Model No.: SSR-80DA;If you want to reach 80A, you need to add a large heat sink and fan.
  • output Voltage : 24-480vac;Special attention:This relay cannot be used for more than 30A for a long time.If that actual use current exceeds 15A,It is necessary to separately configure the heat sink..
  • Total size (approximate) : 58 x 45 x 32Mm/2.3" x 1.8" x 1.26" (l*w*t).
  • material : metal, plastic, electronic parts.
Check Stock

Juried Engineering PTC PT2399 Echo Audio Processor Guitar IC DIP-16 (Pack of 20)

Check Stock

Lisle 69300 Master Relay Test Jump Set

  • Includes 8 Jumpers to fit most popular relays.
  • Includes Test Lead Kit for easily and securely connecting Relay Test Jumpers to a multimeter.
  • Terminal Leads with switch, fuse and power options provide easy access to check current or voltage on many fuses and relays used on vehicles today.
  • Also allows testing of relay configurations not covered by eight Relay Test Jumpers, like Volkswagen, BMW and other European vehicles.
  • Relay Puller Pliers easily remove electrical relays.
Check Stock

ANMBEST 2PCS 4 Channel 5V Relay Module with Optocoupler High or Low Level Trigger Expansion Board for Raspberry Pi Arduino

  • It is 4 Channel Isolated 5V 10A Relay Module, each relay can individually switch on/off by an opto-isolated digital input, Standard interface can be directly connected with microcontrollers and be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, DSP, etc., very convenient..
  • Equipped with high-current relay, maximum load: AC250V 10A, 15A 125VAC, DC30V 10A.
  • RELIABLE: Fault-tolerant design, even if the control line breaks, the relay will not move.
  • With optical coupling isolation, triggering more reliable, more stable..
  • EASY to INSTALL: Equipped with screwed terminal plate and fixed bolt holes(diameter: 3.1 mm) on both sides for easy installation..
  • High/Low level trigger can be selected by jumper. Very versatile, you can reverse the input logic with the jumper..
Check Stock

AOICRIE 12V 16-Channel Relay Interface Board Module Optocoupler LED LM2576 Power for Arduino DIY Kit PiC ARM AVR

  • ★12V 16-Channel Relay interface board, and each one needs 15-20mA Driver Current.
  • ★Equipped with high-current relay, AC250V 10A.
  • ★The control signal voltage range: the trigger signal is low 0-2V.
  • ★Standard interface that can be controlled directly by microcontroller (for Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP433, TTL logic).
  • ★DC 12V 16 Channel Relay Module Interface Board With Optocoupler Protection LM2576 Power for Arduino DIY Kit.
Check Stock

Macurco TX-6-AM Ammonia NH3 Low Voltage Fixed Gas Detector Controller Transducer

  • Fan relay actuation: Selectable from 15 to 75 ppm Nh3.
  • Output: fan relay, alarm relay and 4-20ma current loop.
  • Controls: Digital display (0-100 ppm), buzzer, fan Delay, fan minimum runtime.
  • Mounts on a standard 4” x 4” electrical box.
  • 5 a spdt fan relay controls starters of exhaust fans.
Check Stock

Hilitand AD22B04 12V Signal Decoder 4 Channel DTMF Tone Relay Phone Remote Control PLC

  • 【12V】Working voltage is DC 12V, you can easily find suitable power for this relay..
  • 【reverse polarity protection.】This signal decoder relay ahs reverse polarity protection which can extend the service life..
  • 【8 modes】8 modes of operation: Non-locking (Momentary ), self-locking (Toggle), inter-locking(Latch), 5/20/60/120/250-second delay..
  • 【default control】The default control command is 1/2/3/4. Example: Dial 1 to control relay 1, dial 2 to control relay 2, dial 3 to control relay 3, dial 4 to control relay 4.
  • control commands can be changed any 1-4 bits. (For more details, refer to "AD22B04_4 channel DTMF controller commands setting manual ")..
  • 【operating current】Standby 11-13 MA, 1 relay "open" 44MA, 2 relays "Open" 77MA, 3 relays "Open" 110MA, 4 relays"open" 140MA..
Check Stock

NOYITO 0-5A AC Current Detection Sensor Module Switch Output (DC 12V, Green)

  • Current detection range: AC 0-5A.003cbr003e.
  • Operating voltage: DC 5V / 12V / 24V ± 0.2V. (Select the corresponding version of the product according to your needs).003cbr003e.
  • Output mode: relay switching output.003cbr003e.
  • Relay load: AC 250V 10A Max , DC 30V 10A Max.003cbr003e.
  • Application: Intelligent trolley motor over-current detection, motor stall protection current detection, short-circuit protection detection, etc. (The second picture on the left is the schematic and the third picture is the wiring diagram)003cbr003e.
Check Stock

Baomain SSR-60DA 60A Solid State Relay Module 4-32VDC / 24-480VAC + Heat Sink

  • Photocoupler isolation between input control signal and controlled power, isolation surge voltage up to 7500V..
  • Input signal turn-on voltage DC 3 to 32V, turn-off voltage DC 0 to 0.8V. LED indication for relay turn-on..
  • Output voltage range: AC 90 to 250V(50/60Hz). Maximum on-state average current 3 Amp. Maximum on-state current 10 Amp (003c 10 seconds). Non repetitive surge peak on-state current: 120 Amp (003c20mS). Load type: General purpose..
  • This is a simple and practical solid state relay module, which is very convenient to use, for Arduino, Raspberry Pi, ESP32, PLC or other projects. The GPIO of these controllers are directly connected to this relay input to control the mains power, and it is suitable for most loads less than 350 Watts (for 115VAC)/700 Watts (for 230VAC)..
  • Compact ABS plastic case and wires connect for easy mount. Two screw mounting holes are convenient for you to fix it on the wall or wooden board. Of course, you can also choose not to lock the screw..
Check Stock

AITRIP 8 Pack 3V 1 Channel Relay Power Switch Module with Optocoupler Opto Isolation High Level Trigger for IOT ESP8266 Development Board

  • 【30VDC 250VAC Load】 Equiped with high-current relay, AC250V 10A.
  • DC30V 10A, each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
  • 【High Level Trigger】The relay module is triggered by high level signal, which can be input from microcontroller IO..
  • 【 3V/3.3V power relay module】- This Relay Board provides a single relay that can be controlled by any 3V/3.3V digital input from your microcontroller IO..
  • 【Wide Application】- These 3v relay board works well with ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4/3.3V /NodeMCU/ ESP8266 module etc..
  • 【Long Life】 - Fast response time less than 20ms and long lifetime up to 100,000 times snap action with diode freewheel protection..
Check Stock