ReviewsCurrent Sensing

Fluke 325 Clamp Multimeter AC-DC TRMS

Digital clamp meter measures AC current to 400 amp, AC and DC voltage to 600V, and resistance to 4 kilohms.
True RMS sensing meter provides accurate readings when measuring linear or non-linear loads, regardless of waveform.
Jaw opening measures current in a conductor up to 30mm without touching or interrupting the circuit.
Audible continuity sensor confirms that the circuit conducts electricity.
Meets IEC safety standard 61010-1, and is rated for CAT IV installations to 300V and CAT III installations to 600V.

Check Stock

Slim DIN Rail Mount AC/DC Current Sensor Module, Based on ACS712. (+/-20Amp)

The item disign based on ACS712 IC. The item provides economical and precise solutions for AC or DC current sensing in industrial, commercial, and communications systems. Typical applications include motor control, load detection and management, switched-mode power supplies, and overcurrent fault protection..
Operating Voltage: Regulated 5VDC. Operating Current: 20mA(max). Load Maximum Current: +/-5Amp, +/-20Amp and +/-30Amp selectable. Load Frequency Bandwidth: DC ~ 80 kHz. Minimum Isolation Voltage: 2.1 kV(RMS). Output voltage proportional to AC or DC currents. LED indicator for power supply +5V. Pin jumper option for signal output capacitor..

Check Stock

Harmony Audio HA-A1500.1 Car Stereo Class D Amp Mono 3000 Watt Subwoofer Amplifier - 1 Ohm Stable - Includes Bass Remote

Power – 500 Watts Max x 2 @2-Ohms, 250 Watts Max x 2 @4-Ohms, 1000 Watts Max x 1 Bridged @4 Ohms.
Full Range – With a Full Range amplifier you not only have the option to run your speakers, but also your subwoofers.
Class A/B Topology – Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal.
Mosfet Power Supply – A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry.
Variable Gain Control – The gain control is not for adjusting volume. It simply adjusts the amount of signal that is coming from your receiver and going to your amplifier.

Check Stock

BOSS Audio Systems Elite BE1500.1 Monoblock Car Amplifier - 1500 Watts, 2 4 Ohm Stable, Class AB, Mosfet Power Supply, Great For Subwoofers

POWER: 1500 Watts Max x 1 @2-Ohms, 750 Watts Max x 1 @4-Ohms.
CLASS A/B TOPOLOGY: Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal.
MOSFET POWER SUPPLY: A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss And eliminating all secondary feedback circuitry.
VARIABLE LOW-PASS CROSSOVER: Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction.
SWITCHABLE BASS BOOST: Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.

Check Stock

Pump Boys and Dinettes

Power – 450 Watts Max x 4 @2-Ohms, 225 Watts Max x 4 @4-Ohms, 900 Watts Max x 2 Bridged @4 Ohms.
Class A/B Topology – Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal.
Full Range – With a Full Range amplifier you not only have the option to run your speakers, but also your subwoofers.
Mosfet Power Supply – A MOSFET is basically an electrical switch that allows the flow of electrical current. It controls the output voltage & current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry.
Variable Gain Control – The gain control is not for adjusting volume. It simply adjusts the amount of signal that is coming from your receiver and going to your amplifier.
Variable BASS Boost – With Variable Bass Boost you have the control of exactly how much BASS you want to pump out to your subwoofer(s).
Bridgeable – Dramatically increase the power output to you speakers and subwoofers by connecting two amplifier channels.
Specs – Dimensions: 13.5” x 10.31” x 2.25, Weight: 12 lbs..
Warranty – BOSS Audio Systems provides a powerful 6-year Platinum Onli....

Check Stock

BOSS Audio Systems PT1000 2 Channel Car Amplifier - 1000 Watts Full Range Class A/B 2-8 Ohm Stable Mosfet Power Supply Bridgeable

Power - 500 Watts Max x 2 @2-Ohms, 250 Watts Max x 2 @4-Ohms, 1000 Watts Max x 1 Bridged @4 Ohms.
Full Range - With a Full Range amplifier you not only have the option to run your speakers, but also your subwoofers.
Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal.
Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry.
Variable Gain Control - The gain control is not for adjusting volume. It simply adjusts the amount of signal that is coming from your receiver and going to your amplifier.

Check Stock

BOSS Audio Systems PF1800 4 Channel Car Amplifier - 1800 Watts Full Range Class A-B 2-4 Ohm Stable Mosfet Power Supply Bridgeable

Power - 450 Watts Max x 4 @2-Ohms, 225 Watts Max x 4 @4-Ohms, 900 Watts Max x 2 Bridged @4 Ohms.
Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal.
Full Range - With a Full Range amplifier you not only have the option to run your speakers, but also your subwoofers.
Mosfet Power Supply - A MOSFET is basically an electrical switch that allows the flow of electrical current. It controls the output voltage & current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry.
Variable Gain Control - The gain control is not for adjusting volume. It simply adjusts the amount of signal that is coming from your receiver and going to your amplifier.

Check Stock

Fluke 324 True RMS Clamp Meter

Digital clamp meter measures ac current to 400 amp, ac and dc voltage to 600v, and resistance to 4 kilohms.
True RMS sensing meter provides accurate readings when measuring linear or non linear loads, regardless of waveform.
Jaw opening measures current in a conductor upto 30 millimeter without touching or interrupting the circuit.
Audible continuity sensor confirms that the circuit conducts electricity.
Meets IEC safety standard 61010 1, and is rated for CAT IV installations to 300V and CAT III installations to 600V.
CAT IV 300V/CAT III 600 Volt safety rating.

Check Stock

Flushmate M-101526-F41 504 Series fits porcelain manufacturers Lamosa 3468 and Vorten 3468 tanks

EFFORTLESS UPGRADE: Upgrading into automatic toliet without replacing the current toilet or toilet seat, AND the manual handle will be still working....
RELIABLE MOTION SENSOR, ADJUSTABLE SENSING RANGE & FLUSH TIME: Minimizing possibilty of phantom flash, only be activated when sensing motions within....
EASY TO INSTALL & REPLACE BATTERIES: Simple installation taking most people less than 20 minutes. External battery design makes it easier to replace....
LONG LIFESPAN: The controller last for over 200,000 flushes in normal use and 4 AA batteries (included) last 30,000 flushes..
RIMINDERS: The kit DOESN'T FIT ALL TOILET TYPES! Only fits with most flapper and canister toilets, not for dual-flush/ ballcock valve/ top-mount flush....

Check Stock

BOSS Audio Systems PM1500 Monoblock Car Amplifier - 1500 Watts 2/4 Ohm Stable Class A/B Mosfet Power Supply Great for Subwoofers

Power - 1500 Watts Max x 1 @2-Ohms, 700 Watts Max x 1 @4-Ohms.
Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its outputs with no audio signal.
Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage & current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry.
Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction.
Low & High Level Inputs - A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your speakers.

Check Stock

Megger 212159 Analog Hand-Crank Insulation Tester, 2,000 Megaohms Resistance, 100, 250, 500, 1000 V Test Voltage

Insulation tester for measuring insulation resistance and voltage.
Average-sensing meter provides accurate readings when measuring linear loads, where the current or voltage has a sinusoidal waveform.
Analog meter with manual range selection for flexibility of use.
Guard terminal to eliminate surface current leakage.
Safety rated to European Standard EN61010-1 Category II, 300V and Category I, 600V.

Check Stock