ReviewsCylinder Heads For Ford 2

Motion Raceworks Vacuum Boost Reference Billet Aluminum Distribution Block

  • This billet aluminum vacuum/boost reference billet distribution block is made to simplify and clean up plumbing lines for boost and vacuum purposes on your boosted LS engine..
  • The design allows the block to be mounted universally or off the upper two most holes on LS1 cylinder heads front or rear as well as on a firewall, or anywhere else. This manifold is CNC machined from 6061 aluminum and features 8 separate 1/8 NPT ports and 2 1/4" NPT ports (on each end) giving you many different options for line routing and enough spaces for all of your boost reference signals.
  • This works great for plumbing to your boost reference fuel pressure regulator, manifold pressure wastegates, blow off valve, map sensor, boost controller sensor and many other items. Comes with two stainless button head bolts with the correct length and thread to mount block to cylinder heads..
  • Comes complete with 4 1/8" port plugs and 1 1/4" port plug standard..
Check Stock

SBC Small Block Chevy V8 Cylinder Head Bolt Set

  • OEM-quality Grade 8 cylinder head bolt set (does both heads).
  • Replacing head bolts is cheap insurance to prevent downtime in the shop.
  • For use with cast iron cylinder heads (without washers).
  • 120,000 PSI proof load, 130,000 PSI yield strength, 150,000 PSI tensile strength.
  • Threads are coated with sealant to save you time durng assembly.
Check Stock

Complete Tractor 1100-5109 Tune Up Kit Compatible with/Replacement for Ford/New Holland 2N, 8N, 9N 4 Cylinder W/Front Mount 309786

  • Specs: Description: Complete Tune Up Kit, Notes: For 4 cylinder models w/front mount distributors..
  • Replaces OEM Numbers: Ford/New Holland: 309786.
  • Compatible With / Replacement For: Ford/New Holland 2N, 8N, 9N.
  • 100% New aftermarket Complete Tune Up Kit built to meet OEM specifications for Ford/New Holland.
Check Stock

NICHE 64mm 347cc Standard Bore Left and Right Cylinders For Yamaha Banshee 350 2GU-11311-00-00 2GU-11321-00-00

  • Part Number:16022-03040,16032-03040,16027-03040,16032-03042.
  • Compatible models:Kubota Tractor B7610 B2100 B26 B2620 B2410.
  • Kubota Utility Vehicle RTV1100 RTV1100CW9 RTV1140CPX.
  • Front Mower F2400 F2560E 2880 F2880E F2680E FZ2400.
  • Note: The Complete Cylinder Head of this link is a D1305 cylinder head assembly without a hole, and the hole position of the glow plug is M8. See link picture 2 for details..
  • In addition, if you want a D1305 cylinder head assembly with holes or D1305 bare cylinder head, or other types of cylinder heads, you can contact us, we have a professional team engaged in this product!.
  • If you are not sure which cylinder head you need, you can contact us directly, and our professional team will find the right product for you. Our service philosophy is customer first, thank you!.
Check Stock

OEMTOOLS 37138 Compression Tester Gauge Set, Compression Tester Automotive, Engine Compression Tester with Flexible Hose, 14mm and 18mm Adapters

  • ESSENTIAL CYLINDER COMPRESSION TESTER: Monitor the health of your engine with an accurate reading from our tester.
  • Featuring a 14mm and 18mm adapter for spark plug ports.
  • Read the condition of your engine’s cylinders with our easy-read pressure gauge.
  • ACCURATE COMPRESSION READINGS: Our engine compression gauges give you an accurate reading of engine's compression.
  • The compression test kit's flexible rubber hose extension allows you to easily access spark plug ports.
  • GREAT FOR CARS AND TRUCKS: Maintaining your vehicle’s engine is essential to the longevity of the vehicle.
  • Work on cars and trucks with the cylinder compression test kit's 2-step 14mm and 18mm adapters to determine the health of your cylinders.
  • DIAGNOSITC TOOL: Diagnose problems with your vehicle’s cylinders using our engine compression test kit.
  • Valves sticking, cracked cylinder heads, worn cylinder walls, and more can be diagnosed with our cylinder compression tool.
  • PRODUCT SPECIFICATIONS: This compression tester kit features a flexible rubber hose extension to reach spark plug ports.
  • (2) 2-step adapters sized 14mm and 18mm for cars and trucks.
Check Stock

Fuel Injection Pump fits Ford 4000 545 531 4600 535 532 540 515 D0NN9A543K

  • Compatible with Ford Tractor(s) 4000, 4600.
  • Compatible with Ford Construction & Industrial(s) 515, 531, 532, 535, 540, 545.
  • Replaces Ford OEM nos D6NN9A543G, D0NN9A543K.
  • Replaces CAV - Lucas Mfg nos 3233F390, 3833F390.
  • All models listed with 3 Cylinder - 201 cu. Engine.
Check Stock

PAGOW Spark Plug Boot Wire Removal Tool Ignition Coil Puller for Volkswagenn Audi VW Hand Install Repair Tool

  • Best Compatibility: The spark plug wire puller installer can perfect match with Volkswagen and Audi vehicles with standard prong plug caps on each side (not recommended for non-VW/Audi plug leads). Volkswagen – New Beetle 2.0 engine AZJ (AEG), Golf IV & V 1.6 engine (AVH), 1993-2005 2.0L 4 cylinder (AZG), 1998-2006 1.8L 4 cylinder (BBW), 2006 and later 2.0L 4 cylinder turbo (BDC).
  • Audi – 1998-2006 1.8L 4 cylinder turbo (BEV), 2006 and later 2.0L 4 cylinder turbo (BGD)..
  • Size Inforamtion: The size of spark plug boot removal tool kit: 12.6inch (32cm) overall length, 3.75inch x 0.4inch x 1.2inch (9.5cm x 1cm x 3cm) handle, 9.25inch (23.5cm) shaft, 2.2inch x 0.8inch (5.6cm x 2cm) boot end..
  • Wide Applications: The spark plug puller tool suitable for Bora, Mercedes, Smart, and other Volkswagen and Audi vehicles with similar engines and standard prong plug caps on each side..
  • Easy to Use:Perform spark plug change when engine is cold to prevent the heads from stripping. After pulling the plugs, we recommend applying lubrication to make the job easier. When installing wires, refrain from pushing too hard without the tabs aligned on the tool to prevent the boot end from spreading and getting stuck..
  • Material:The handle of ignition coil puller is made of hard p....
Check Stock

ICT Billet 4pc LS Cylinder Head Install Alignment Dowel Pin Steel LT Gen 3 Gen 4 Gen 5 LSX LS1 LS3 LS2 LQ4 LQ9 LS6 L92 L99 L33 LR4 L82 L83 L84 L86 L87 LT1 L8B 551275

  • Replace Your Rusty or Missing Dowels Before you Assemble Your Engine.
  • These are Required when Installing Cylinder Heads on Your LS Engine.
  • Compatible with all Gen 3 4 and 5 LS/LT Series Engine.
  • Includes 4 Dowel Pins Enough to install 2 cylinder heads.
  • Stock replacement cylinder head bolts also available for LS engines.
Check Stock

COMP Cams 4705-16 ID Spring Locator Set of 16-1.300\ OD.570\ ID.060\ Thickness

  • ... to their appropriate installed height. Since they are available in multiple locator thicknesses, these locators eliminate the need to stack shims, while also adding to valvetrain stability and durability..
  • Protect Your Head - Valve springs should never be installed directly on aluminum heads. Protect your expensive cylinder heads by installing springs on our hardened steel spring locators..
  • Made to Measure - Made for both factory and aftermarket cylinder head dimensions, these spring seats are available for nearly any engine. With options in multiple O.D.'s (outside diameters), I.D.'s (inside diameters) and thicknesses, COMP has a locator to fit your valvetrain project..
  • Precision Machined for Consistency - Crafted in-house, using the best machining equipment, COMP Cams seats and locators are precision machined to ensure consistent thickness and inside/outside diameters for a perfect fit everytime..
  • Quality Guaranteed - COMP Cams' valve spring locators are made from a hardened steel alloy that not only protects expensive cylinder heads but also ensures the durability of valve springs, valve guides and retainers. Held to the tightest tolerances in the industry, our locators are a worthwhile investment for your next spring change..
Check Stock

Lisle 68500 Manifold Drill Template for Ford 2V & 3V

  • Interchangeable plates and alignment pins ensure drill is centered on the broken stud.
  • Depth gauge for drilling is marked on the template. Designed to remove broken exhaust manifold studs on 4.6L, 5.4L and 6.8L V10 2 valve and 3 valve Ford Triton engines without damaging the cylinder head..
  • The stripped screw extractor is then used to remove the broken stud.
Check Stock

Racer Walsh RWA1488 2.3L Mechanical Lifter Lash Adjuster Set - For Camshafts Using Stock Length Valves

  • Easily adjust valve lash for 2.3L Ford cylinder head with any size mechanical cam.
  • For use with .100 longer than stock valves.
Check Stock