ReviewsCylinder Valve Protector

New 60 cu ft Steel Oxygen Cylinder with CGA540 Valve

New, high-quality 60 cu ft steel oxygen cylinder with CGA540 valve.
Thick walled steel tank, with the durability to stand up to any work site.
7″ diameter x 22.5″ in height with valve - approximately.
All cylinder ship empty. Please consult your local compressed gas supplier for filling needs..

【Cylinder Bore】: 47mm / Non-EGR Cylinder.
【Apply to】: GY6 4 stroke 49cc 50cc 60cc 80cc engine upgrade for most of chinese scooter, atv and go karts.
【Parts included】:GY6 80cc Cylinder Head with 64mm valve, 47mm Bore Cylinder Block, Set of 47mm Piston Assy, Piston, Rings and Wrist Pin, Full Set of Engine Gasket, 6pins CDI, Ignition coil, 4pin AC regulator, relay, A7TC Spark Plug, Set of Intake Manifold and Muffler Bolts, and Exhaust locking ha, Set of 8.5 Gram roller , Rocker Arms, Valve Seals, Oil Pump Assy with Driving Gear, Camshaft, Camshaft chain 82, belt 699*18*30, Chain adjuster, Oil screen, spring, cover and oil seal, Starter clutch.
【Fit to】Roketa, Sunl, Baja, Taotao, Panterra, Redcat Tank Giovanni Wildfire Xtreme Seaseng Qlink Yiben Jonway Jmstar, Vento.

The Soda Stream CO2 Cylinder Refill Adapter refill adapter can be used to refill small CO2 tanks from larger CO2 tank,the standard should be CGA320..
Please upside down your CO2 tank if you can not refill when the CO2 tank standing,because some of tank have not the dip tube (syphon tube)inside..
The cylinder should be empty.Pre Cooled cartridges will get quite full..
You should open the tank valve very slowly when you filling the protection valve(6mm wide pin) of sodastream bottle..
Our adapter don’t work RPV valve (residual pressure valve),but some of RPV valve can be removed by hex wrench,please check before ordering.

Powder coated cylinder for high gloss, durable finish.
Reusable and conforms to dot-4ba400 specifications and ari guidelines.
3/4" npt opening accepts 80 percent fill float switch shut-off device (does not included the float switch valve, if you need it, please see master cool part # 62011 which includes it).
Pre-charged cylinder provides a clean, dry interior.

RACE READY PERFORMANCE: With the BBR Tuning Racing Series DIO Cylinder Body & Reed Assembly with OKO 21mm Carburetor w/ Velocity Stack you’ll get the power and speed your build’s been looking for. A ported cylinder body with a high performance reed valve intake system, this race assembly was made for race engines in mind..
PORTED CYLINDER: Unlike other cylinders, the BBR Tuning Racing Series DIO Cylinder Body is ported to allow maximum fuel and air mixing within your motor. The exhaust port can fit nearly any performance muffler as well as any stock exhaust muffler you want to run, which the intake port is specifically designed to accept the reed valve assembly included with this kit.
BOOSTS POWER: With a 32mm opening, you’ll be able to fit hardcore racing carburetors like the BBR Tuning High Performance 2-Stroke OKO Style Carburetor without a single problem. With the right carburetor, this reed will deliver tons of fuel and air to your motor and give you higher speeds and even more torque..
COMPLETE KIT: The BBR Tuning Racing Series DIO Cylinder Body & Reed Assembly is paired with a 21mm OKO Race carburetor is racer’s dream setup- get ready for a bike that’ll scream whenever you hit the gas!.
INCLUDES: Modified BBR Tuning Racing Series DIO Cyl....

Cavagna AUTOMATIC CHANGEOVER REGULATOR - Kit Includes Mounting Bracket And Plastic Cap Cover Automatically switches from empty service cylinder to full reserve cylinder, ensuring continuous gas flow to appliances.
Highly visible full/empty indicator signals need for refill.
Built-in back check valve allows empty cylinder removal and refill as reserve cylinder remains operational.

Fitment -- Fits for Most Overhead Valve Engines With Valve Stems From 4.5 to 7.5mm and 5/16" to 3/8".New smaller size Fits for Toyota four cylinder and for Chrysler New World Engine applications. Works on automobiles, motorcycles, and boats..
Function -- Used to removes and installs Valve Keepers On the above model quickly and smoothly and without disassembling the cylinder head..
Usage -- The disassembly of the valve keepers: push or tap the tool with a hammer. The installation of valve keepers: load in retainer on valve stem, then push or tap handle to install. Can be used in a car or on a bench..
Design -- A magnet is built into the main body of the tool to attract and fix the retainer immediately before it falls into the engine. Avoid any potential damage..
Superior Material -- Made of high quality steel, CNC process precision manufacturing, sturdy and durable, rust resistant, impact-resistant, corrosion-resistant ensure the tool is not bent and the valve spring is not loose for a long-term and reliable performance..

【Easy to Connect】Integrated safety pressure valve with 3000psi pressure gauge, easy to connect..
【Compatibility with Any Cylinder】The adjustable valve pin ensures compatibility with any cylinder valve changes..
【Easy to Install and Use】8mm male head with filter screen, easy to use, can fill carbon dioxide into soda bottle..
【No Gas Leakage】With gasket and sealing rubber rings, good sealing performance, no gas leakage..
【High Quality Material】CO2 connection valve adopts aluminum alloy, which is long-lasting and corrosion‑resistant..

NEW! REPLACEMENT FOR YAMAHA TIMBERWOLF 250 YFB250 2X4 / 4X4 CYLINDER HEAD ASSY 1992-2000.
THIS BRAND NEW AFTERMARKET KIT HAS BEEN INSPECTED FOR THE HIGHEST QUALITY & THE HIGHEST GRADE MATERIALS HAVE BEEN USED IN THE MANUFACTURE OF THIS KIT.
PURCHASE INCLUDES: CYLINDER HEAD ASSEMBLY. ( HEAD INCLUDES: EXHAUST & INLET VALVES, VALVE SPRINGS, CAMSHAFT, ROCKER ARMS, VALVE RETAINERS ). CAMSHAFT COVER. VALVE COVERS. CAMSHAFT PLATE. HEAD VENT TUBE. O-RING KIT. NUT, BOLT & WASHER KIT. NGK SPARK PLUG..
REPLACEMENT FOR OEM Part # 4BD-11101-03-00.