ReviewsDrive Shaft Puller Tool

ABN Inner CV Axle Removal Tool - CV Axle Puller Slide Hammer Set with 5 lb Slide Hammer and CV Joint Puller Adapter

[Remove Front Wheel Drive Axles Easily] To replace or repair your CV axle joints easily, use the ABN FWD Axle Puller Slide Hammer Puller Set.
The CV joint puller adapter and large slide hammer bearing puller allow you to create added torque to loosen and remove stubborn axle shafts and water pumps.
[Fits Your Needs] Chrome-plated 23 x 5/8-inch hammer bar features a 5/8-inch x 18 threaded section to fit your adapters, while the slide hammer CV axle adapter has 48mm (roughly 2-inch) opening and a 2.5-inch depth to fit your needs.
[Easy to Use] Attach the inner CV axle puller to your axle slide hammer then position the adapter around the shaft behind the inner boot.
Slide the 5 lb hammer weight back and forth to create torque to pull out the axle.
Use lubricant fluid for added ease (not included).
[Safe for Your Vehicle] Slide hammer CV joint puller and attachment design focuses the added torque to the back of the housing to prevent damage to the roller bearing inside the joint.
Pulls CV joints on 1986-current Taurus/Sable.
[Built to Last] Hardened hammer shaft provides strength and d....

Check Stock

Sunluway - 12020-2 Pack Axle Popper Kit - Inner CV Axle Removal Tool Set - for Use on Front Wheel Drive Vehicles-Remove Most Vehicles’ Half-Shaft Drive Axles-Fix Damaged CV Joints

Easy to disassemble: Skip the complicated slide hammer puller sets and pry bar tools that can cause damage to your axle, use this CV shaft tool to easily disassemble the CV shaft, saving your time and energy !.
Material: CV Axle Removal Tool Set made of high-strength hardened steel, which has high hardness, high strength, with stable performance and reliable use and longer service life.
Benefits: Better and Safer than Using a Hammer and Bar because the wedge-shaped fork end of the axle Popper applies uniform pressure to both sides of the shaft To ensure safe release (Two piece CV axle popper tool kit ensures fitment for most FWD vehicles).
Easy installation: Insert the wedge wheel bearing tool between the transaxle case and the axle joint, and the fork head surrounds the axle end, tap the end of the front fork to release the axle shaft. these axle puller tools are simple, yet powerful, Is your essential tool !.
100% Satisfaction Guarantee: If you're not 100% satisfied with our , please feel free to contact us, simply return it for a full refund in 30 days. Premium Support & 12-Month Warranty..

Check Stock

Auto Body Now ABN Harmonic Balancer Puller 46-Piece Tool Kit – Flywheel Remover, Crankshaft Pulley Removal, Steering Wheel Pulling Set

[Effortlessly Remove Harmonic Balancers] Use the ABN 46 Piece Harmonic Balancer Puller Kit - Flywheel Puller, Crank shaft Pulley Puller, Steering Wheel Puller Set to apply even pressure to the hub so you can safely remove harmonic balances and other vehicle parts.
[Fits your Vehicle Needs] Steel yoke with 4 slots and 30 harmonic balance puller bolts allow you maximum versatility to handle a range of jobs on most cars, trucks, SUVs, and small engine vehicles.
[Various Bolt Sizes] 3/8-inch bolt in 1-1/2, 2, 4.5, and 6 inch lengths, 5/16-inch bolt in 3, 3.5, and 6-inch lengths, 1/4-inch bolt in 2.5-inch length, M8 x 1.25mm bolt in 45, 65, and 90mm lengths, and M10 x 1.5mm bolt in 35mm length.
Bolts come in a mixture of 16, 18, 24, and 28 thread pitch.
[Built to Last] Heat-treated carbon steel ensures maximum strength.
Chrome and black oxide finishes resist rust and corrosion.
Heavy-duty blow-molded carrying case provides easy transportation, safe storage, and quick organization.
[Package Contents] Crank pulley puller tool wheel balancer gear puller set include (1) 5 inch long 3/4-inch....

Check Stock

Sinoer Hand Weeding Tool for Garden,Weed Removal Cutter,Root Removal Weed Puller,Gardening Weeder Tools for Garden Lawn Yard

Root Remover Tool - Naswei Weed Puller is designed for the permanent removal of weeds. The dandelion puller will remove the roots of plants so that....
Your Gardening Tools - Save time and your back with the stand-up weed puller, which is built with a 39-inch shaft to weed all the way down to the....
Simple operation - Aim the root remover tool at the weeds, start from the upright position, insert the steel claw into the center of the weeds, step....
All-in-one Weeding Tool - Why invest in half a dozen different tools for gardening when you can tackle them all with the step and twist garden/lawn....
Guarantee - We support a detailed answer or a full refund whatever your dissatisfaction about the assembly or quality of our weed puller. Naswei is....

Check Stock

PAGOW Spark Plug Boot Wire Removal Tool Ignition Coil Puller for Volkswagenn Audi VW Hand Install Repair Tool

Best Compatibility: The spark plug wire puller installer can perfect match with Volkswagen and Audi vehicles with standard prong plug caps on each side (not recommended for non-VW/Audi plug leads). Volkswagen – New Beetle 2.0 engine AZJ (AEG), Golf IV & V 1.6 engine (AVH), 1993-2005 2.0L 4 cylinder (AZG), 1998-2006 1.8L 4 cylinder (BBW), 2006 and later 2.0L 4 cylinder turbo (BDC).
Audi – 1998-2006 1.8L 4 cylinder turbo (BEV), 2006 and later 2.0L 4 cylinder turbo (BGD)..
Size Inforamtion: The size of spark plug boot removal tool kit: 12.6inch (32cm) overall length, 3.75inch x 0.4inch x 1.2inch (9.5cm x 1cm x 3cm) handle, 9.25inch (23.5cm) shaft, 2.2inch x 0.8inch (5.6cm x 2cm) boot end..
Wide Applications: The spark plug puller tool suitable for Bora, Mercedes, Smart, and other Volkswagen and Audi vehicles with similar engines and standard prong plug caps on each side..
Easy to Use:Perform spark plug change when engine is cold to prevent the heads from stripping. After pulling the plugs, we recommend applying lubrication to make the job easier. When installing wires, refrain from pushing too hard without the tabs aligned on the tool to prevent the boot end from spreading and getting stuck..
Material:The handle of ignition coil puller is made of hard p....

Check Stock

VQL Harmonic Balancer Steering Wheel Puller Kit (13 Piece) with Blow-Molded Case Use for Removing Harmonic Balancers, Gear Pulleys, Steering Wheels and Crank Shaft Pulleys

【Widely Used】 Harmonic Balancer Steering Wheel Puller Tool are used to removal of harmonic balancers, gear pulleys, steering wheels and crank shaft pulleys. This is a universal type puller.003c/p003e.
【Durable】 13 Piece Harmonic Balancer Steering Wheel Puller Kit are made of high-quality steel, Drop Forged, Heat Treated, this tool set is very durable.003c/p003e.
【Apply Pressure Evenly】 Yoke allows for either 2 or 3-hole application. The harmonic balancer puller allows uniform pressure on the parts, No need to worry about the steering wheel puller and harmonic puller puller kit will damage the auto parts.003c/p003e.
【Package Included】 1* center screw, 1* Floating swivel, 2* 5/16 x 4 bolts, 2* 1/4 x 3 bolts, 3* 1/4 x 2 bolts, 3* 5/16 x 2 bolts and 1* Blow-molded Case.003c/p003e.
【Various Sizes】 Steering wheel pullers has a caster with four slots for using in nearly any configuration. Various sized provides necessary versatility.003c/p003e Buy with confidence. We provide refund and exchange service, if you have any questions, please feel free to contact us.003c/p003e.

Check Stock

Outboard Trim/Tilt Pin Wrench Tools Set - MT0004 & MT0006 & MT0009 Fit for Yamaha Suzuki Johnson Evinrude

Application -- Compatible with Mercruiser Alpha Alpha 1 MR Bravo OMC Cobra Volvo. With this tools set, you could replace gimbal bearings and hinge pins..
Gimbal Bearing Puller -- This bearing puller remover can easily remove the gimbal bearings on bell housings by turning the end of the tool with a wrench..
Gimbal Bearing Installer -- Used to install the new gimbal bearing back, set the bearing on the installer than insert the installer in engine. Also it can be used to check engine coupler alignment with the gimbal bearing and drive..
Hinge Pin Tool -- This tool is used to remove and install hinge pins for Mercruiser drive units. It can separate the housing from the gimbal ring on the hinge pin bolt..
High Quality -- Our tool set is made of premium solid steel with nice black Oxide finish which is anti-corrosion and rustproof. The tools are specially hardened for added strength and impact protect. So the product can be durable and service a much longer time..

Check Stock

Zinger Mercury Mariner Outboard Lift,Flywheel Puller Removal Tool 91-849154T1,Lift Ring 91-90455-1

Flywheel puller with crank shaft protector 91-849154T1,Lifting Ring 91-90455-1.
A must have tool when changing Mercury outboard motors on boats and lifting the engine off transom.
Nice craftsmanship and solid. 5/8"-18 TPI Bolt and Lift Ring Threads.
For Most 45HP+ Mercury, Mariner, Force and Yamaha outboard motors with 1 1/2"-16 TPI threads units from the 1960s to present,but pls check thread diameter to verity.
Warm tips: please apply some lube oil on the flywheel and puller tool before use it.Thank you !.

Check Stock

VCT Rear Axle Bearing Remover Puller Slide Hammer Set Remove Semi-Floating

EASY TO USE: Slide flat end of puller through center of bearing and flat against backside of bearing, then slide washer down the center of the shaft against front side of bearing and tighten the nut on smaller end of puller, then thread a slide hammer (not included) to the puller and slide hammer back and forth until the bearing comes out.
The washer captures the bearing firmly to distribute the applied force over the entire bearing and prevent damage.
Use the VCT Pneumatic SAE Standard Rear Axle Bearing Puller 3-Piece Service Set – Domestic Car Vehicle Bearings Removal Tool Kit to service semi-floating rear axle bearings on your vehicle.
These tools make the job simple and prevent damage to your bearings when pulling.
Much easier than claw-type axle bearing pullers that slip off and chew up the old bearings.
For removal only, not intended for installation.
FITS YOUR CAR: Standard SAE sizes work for most American domestic makes and models.
Set includes the following sizes to fit main bearing tube – 1 inch to 1-7/8 inches, 1-5/16 inches to 2-3/8 inches, and 1-3/8 inches to 2-7/8 inches.
Sizes permanently laser-etched on tool for easy identification.
Each tool fits a basic slide hammer with a 5/8-inch x 18 thread pitch.

Check Stock

Weed Puller Tool, Stand Up Weed Puller Long Handle Removable Steel Tube and Non-Slip 4 Claw Iron Head Design, Grandpas Manual Weeders Easily Remove Dandelion Root Tool Gardening Lawn Yard（49 In）

ꕥ【Upgraded Weed Puller】Stand up weed puller has been upgraded from cast aluminum to metal iron, which solves the problem of 4-claw head, broken and bent wooden poles. Metal long shaft and 4-claw iron head spray paint will not rust. The weed puller is added with anti-slip function, uprooted weeds, making it an ideal weeding tool the garden tools for gardening..
ꕥ【Stand Up Weed Puller】The long handle standing up weeder is removable and has a length of 49 In. The grandpas weeder improves the traditional bending over to pull weeds, which can pull out weeds with one hand, without the need to bend over or kneel to pull weeds, and avoid back pain. The garden weeder is a good gift for grandfather, grandmother, grandpa, grandma, father, mother, husband and wife.
ꕥ【Metal Iron Manual Weeders】The hand weeder tool is made of metal iron. It consists of 4-claw iron head, long-handled steel pipe and nut. Compared to other plastic, aluminum and wooden weeders, DMDMBSR weeders are more durable. Whether it's dry weather or after a rain, hand weeders can uproot weeds..
ꕥ【How To Use? 】The weed puller is easy to use. The 4-claw iron head of the standing weed puller is aimed at the weeds, and the pedals are inserted into the soil, and the weeds and roo....

Check Stock

Slide Hammer, Orion Motor Tech 9-Way Internal/External Slide Hammer Puller Set - Pulls Hubs, Rear Wheel Axle Shafts, Bearings, Bushings, Seals, Retainers

VERSATILE PULLER SET: The Orion Motor Tech 9-Way Slide Hammer Puller Set with 5 lb slide hammer is ideal for many pulling applications like flange-type rear axles, most front-wheel drive hubs, pulling dents, and other press-fit parts (bearings, bushings, gears, pulleys, etc.)..
INTERNAL & EXTERNAL JAWS: Includes 2-jaw and 3-jaw pullers for internal and external work to provide a variety of combinations to pull bearing, gears, and seals. 2 and 3-way cross blocks and cone-type puller provide the perfect jaw configuration for most jobs..
MULTI-FUNCTION: Includes a grip wrench adapter and a dent puller attachment for sheet metal or other unique pulling requirements. All the tools are contained in a heavy-duty organizer case to extend the life of your tools..
ULTIMATE DURABILITY: Built to last with rugged carbon steel alloy and chrome vanadium steel components, our tool kit can withstand accidental drops and years of heavy use without cracking or rusting..
ALL-IN-ONE TOOL SET: Complete 15 piece set for a wide range of pulling applications, including: Slide Hammer, Puller Head, Pulling Adapter, Cross Block, Internal/External Puller Jaw, Hex Jaw Nuts & Screws (3), Vise-Grip Adapter (single-lead thread), Seal Hook, 3-Way Puller Head, Cone, Self-Tapping Screw and....

Check Stock