ReviewsEvinrude Power Trim Fluid

Mangrove Products: Boat Transom Saver, Outboard Motor Support, Single Ram Wedge, Boat Accessories, Transom Savers for Outboard Motor, Boat Motor Engine Support, Boat Saver, Pontoon Boat Accessories

✅UNIVERSAL FITMENT: Supports outboard motor brands such as Yamaha, Mercury, Suzuki, Evinrude, Honda, and Tohatsu. Specific Fitment range for outboards with single ram hydraulic tilt systems (See Fitment Guide). The intended use is to support and brace the outboard motor when trailering to prevent any unwanted motor travel up and down when trailering, This unwanted movement can put damaging pressure to the tilt and trim unit's hydraulic system and boat transom without using wedge/block support..
✅EASY TO USE: No drilling or special installation required, no need to bend over or get on your knees. Eliminate metal to skeg scrapping compared to metal transom savers. Simply tilt engine up, insert high pressure wedge into Tilt Ram piston, then tilt down and you are on your way. No metal, no worries of rust or corrosion and is safe to use in both salt and freshwater applications. No need for straps, rope, bungies, skeg support, or brackets. All you need is the high pressure wedge..
✅UPGRADED DESIGN/HIGH PRESSURE SYSTEM: High Density EPDM rubber formula. Trial tested and constructed better by Mangrove Products. Compression testing over 1000 lbs of pressure, exten....

Complete transom saver kit with 5 inch support and two 4 inch locks.
Work on single ram trim and tilt outboards.
Fllowing brands with Yamaha Suzuki Mercury Johnson Evinrude and Honda Tohatsu outboards.
It helps protect your outboard motor and minimizes strain on the boats transom.
Material with Highest Marine Grade Rubber.

Maximum detergency reduces combustion deposits smokeless, ash less and odorless.
Introducing Evinrude/Johnson XD100 oil - a premium synthetic formulation that delivers ultimate performance in direct injection and oil injection....
Evinrude e-tec engine owners can cut their oil usage in half - just by having an authorized Evinrude/Johnson dealer reprogram their outboard to use....
The Best oil for your engine and your wallet.
Ultimate lubricity for reduced friction and wear.

COMPATIBILITY : Fit for all Yamaha Suzuki Johnson Evinrude Hydraulic Trim/Tilt Endcaps, also for All Seastar Hydraulic Steering End Caps..
REPLACEMENT: Equivalent Yamaha Factory Toosl: YB-06175-2B, YB-06175-1A, YB-06548..
STRENGTH: Trim and Tilt hydraulic pin wrench. MT0004 & MT0006 MIN Pin Strength is 180 ft-lb, MT0009 MIN Pin Strength is 200 ft-lb..
PACKAGE: Three of 1/2" socket drive, Pin Wrench with size of MT0004-38mm x 4mm, MT0006-32mm x 4mm/4.5mm and MT0009-35mm x 6mm.
MATERIAL: Made of high quality-42CrMo Steel to ensure resistance to corrosion and rust, protection and years of trouble-free use, also show superior durability and impact resistance. Guarantee with 12 months' warranty..

Replace Johnson/Evinrude #: 5007420, 5007422.
Carbhub 5007420 VRO system conversion non-oiling fuel pump for 90hp-250hp Johnson & Evinrude Outboard motors.
Fits V6 Crossflow and Looper engines, BUT does NOT fit 60 degrees applications.
Interchange Part Number: Volvo 5007420, Volvo 5007422.
Brand new Aftermarket replacement 5007420 vro fuel pump for johnson and evinrude.

High Quality Aftermarket Product / Made to Meet or Exceed OEM Specifications.
New High Quality OEM Spec Johnson Evinrude OMC Piston Ring Kit - Std.
Fits The Following Evinrude Johnson OMC Models: 65hp Jet 1992-1997, 80hp Jet 1991-1997, 85hp 1991-1995, 88hp 1988-1996, 90hp 1981-1998, 100hp 1990-1997, 110hp 1986-1989, 115hp 1974-1985 and 1990-1998, 135hp 1974-1976, 140hp 1977-1984, 150hp 1978-1991, 175hp 1977-1985, 200hp 1976-1983.
Replaces OMC / JOHNSON / EVINRUDE OEM Part Number(s): 393845, 394930, 384539, 385661, 0384539, 0394930, 0385661, 778204, 0778204 ~ Also Replaces Sierra # 18-3904 ~ GLM # 24210 ~ Mallory # 9-54416 ~ WSM # 200-110.

Compatible with OMC, Johnson, and Evinrude engines and tank connectors.
3/8 inches hose with a 6 feet long line. Includes (2) OMC, Johnson, and Evinrude female barb connectors.
Premium primer bulb with a 3/8 inches OMC, Johnson and Evinrude Hose Connector.
Compatible with ethanol blended fuels & pre-assembled using low permeation fuel line and bulb.
Exceeds fuel flow requirements for OMC outboards. Meets current Environmental Protection Agency (EPA) & CARB regulations . FIVE OCEANS, 40 YEARS developing High-Quality Marine & Outdoor Products.

CD-ROM with Evinrude tools, software and drivers and workshop manuals in PDF.
High Quality cable with 3 pin molded connector for long time use.
Works on all windows XP,7,8,10 operating systems 32 & 64 bit.
Step-by-step guide with pictures + technical support if needed.
This kit also includes a 6 FT USB 2.0 extension cable so you can work at a comfortable distance from the engine. Compatible with all models E-TEC, FICHT, DI, G2 1999-2020 : E-TEC: 25HP, 30HP, 40HP, 50HP, 55HP, 60HP, 65HP, 75HP, 90HP, 115HP, 130HP, 150HP, 175HP, 200HP, 225HP, 250HP, 300HP. FICHT: 75HP, 90HP, 115HP, 135HP, 150HP, 175HP, 200HP, 225HP, 250HP. DI: 100HP, 115HP, 135HP, 150HP, 175HP, 200HP, 225HP, 250HP. G2: Supports all Evinrude E-tec/Fitch models 1999-2020.
Supports all Evinrude E-tec/Fitch models 1999-2020.

Fits the following 1977-1984 2 cylinder engines: 4 to 60 HP with no RPM limit.
Replaces part numbers: 581649, 583380, 583453, 581924, 581926, 581927, 582452, 582453.
Check manufacturer's recommended part numbers to ensure a proper fit for your application.

Plastic inline replacement fuel filter for Mercury/Johnson/Evinrude.
High quality filter ensures clean fuel is delivered to your engine.
Molded white plastic for added durability.
Replaces Mercury fuel filter part #35-816296-1 and #35-16494, and Johnson/Evinrude part #398327.