ReviewsFitting Pipe Fitting

1-1/2" 4-way Tee PVC Fitting Connector

  • Furniture Grade means this fitting has a non-marked, glossy finish..
  • DO NOT use these fittings for plumbing projects..
  • The 4 way LT PVC pipe fitting, also known as a side outlet tee or 4 way corner fitting is commonly used to build the sides of a box or cube out of PVC pipe. It is also useful to make the ridge on PVC greenhouses or small PVC buildings. Some dog agility customers use the 4 way LT at the base of jump pole stands..
  • 1-1/2″ Fittings fit on 1-1/2″ Schedule 40 PVC or Furniture Grade PVC. Please check out our PVC Sizing Guide (Specification Sheet) to make sure that you order the correct size PVC Fittings. PVC is NOT measured by the outside diameter, and doing so will result in receiving fittings that are too big for your pipe..
  • All four outlets are non-threaded sockets.
Check Stock

Class A Customs | Under Mount 20 Gallon RV Concession Fresh and Gray Water Holding Tank & Plumbing Kit UM-2000-BPK

  • 20 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 48” Longest Length (not including fittings) x 8.5” x 13” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Th....
Check Stock

Bonbo Fuel Gas Cap with Brass Hose for Honda EU2200i EU1000i EU2000i EU3000i Handi, Champion 2000watt, Westinghouse 2200watt WH2200iXLT Generators, Upgrade Extended Run (Red)

  • Application - This fuel gas cap can be widely used in Honda EU2200i EU1000i, EU2000i, EU3000i Handi, Champion 2000watt, Westinghouse 2200watt WH2200iXLT generators..
  • Function - As a fixed connection between plastic or rubber hose and pipe, this gas cap with brass hose fitting helps you add gasoline into generator within a safe distance, ensuring seal tight and no leakage..
  • Design - The brass hose fitting has a 1/4" male end for connecting to threaded pipe, conforming to National Pipe Thread (NPT) standard and the barbed fitting for a hose is equipped with a 1/4" inside diameter..
  • Material - The gas cap is made of premium CNC billet aluminum, finishing with stylish anodized red coat. And the hose fitting is made of top high quality and wear resistance brass, performing well even under extreme conditions..
  • Satisfaction Guarantee - Bonbo aims to provide best products and services for our customers. If you receive broken or defective gas cap and brass hose fitting, please contact us any time, we will compensate you with 1 year warranty or 30 days full refund..
Check Stock

Class A Customs | Under Mount 30 Gallon RV Concession Fresh and Gray Water Holding Tank & Plumbing Kit | UM-3000-BPK

  • 30 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
  • WATER TANK MEASUREMENTS: 48” Longest Length (not including fittings) x 8.5” x 20.5” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and water-tight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT Over-tighten fitting damage will occur – Use plastic threaded fittings, metal threads may damage tank fittings.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES: (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5”....
Check Stock

SharkBite 1/2, 3/4, 1 Inch PVC Disconnect Clip Set for Push to Connect Brass Plumbing Fittings, PVC IPS (Iron Pipe Size), UIP716A

  • SHARKBITE PVC DISCONNECT CLIP: 1/2, 3/4, and 1 inch disconnect tools are used to perfectly release a SharkBite PVC fitting from any white collar iron pipe-sized fittings.
  • can adjust or remove PVC SharkBite fittings in tight spaces for easy disassembly.
  • COMPATIBILITY: These push-to-connect fitting disconnect tools can be used to release the white collar of a SharkBite PVC fitting from schedule 40, 80, or 120 PVC pipe and schedule 40 and 80 CPVC.
  • ideal for marking proper safe seal insertion depth on a pipe for SharkBite fittings.
  • DURABLE AND HIGH QUALITY: Fitting remover is made of durable and lightweight plastic with wide grip handles by a name you know and trust.
  • SharkBite's quality and performance are field-proven and trusted in the plumbing industry.
  • PREFERRED BY THE PRO: SharkBite tools and fittings meet the same high standards for commercial and residential plumbing applications, combining durability and ease of use suitable for commercial repairs or home improvement projects.
  • MADE IN THE USA: All SharkBite valves, clips, joints, and adapters are manufactured and tested in....
Check Stock

Spears 1429 Series PVC Tube Fitting Coupling Schedule 40 Gray 1-1/2 x 1 Barbed

  • Fitting connects to schedule 40 PE pipe on both ends.
  • PVC for strength and resistance to reactions with acids, gasoline, alcohol, and hydrocarbons.
  • Barbed fitting creates a tight seal on flexible pipe when used with a hose clamp (sold separately).
  • Meets ASTM D 2609 standards for plastic insert fittings and certified by NSF for use with potable water.
Check Stock

Spears 1429 Series PVC Tube Fitting Coupling Schedule 40 Gray 3/4 x 1/2 Barbed

  • Fitting connects to schedule 40 PE pipe on both ends.
  • PVC for strength and resistance to reactions with acids, gasoline, alcohol, and hydrocarbons.
  • Barbed fitting creates a tight seal on flexible pipe when used with a hose clamp (sold separately).
  • Meets ASTM D 2609 standards for plastic insert fittings and certified by NSF for use with potable water.
Check Stock

Class A Customs | 25 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-2500-BPK-PUMP

  • 25 Gallon Fresh Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe WATER TANK MEASUREMENTS 33.5” Longest Length (not including fittings) x 10” x 17”- Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” ID V....
Check Stock

Class A Customs | 42 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-4200-BPK-PUMP

  • 42 Gallon Fresh Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe WATER TANK MEASUREMENTS: 27.5” Longest Length (not including fittings) x 15.25” x 22.5 - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads.
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5” I....
Check Stock

SpringSpray 1-1/2\ NPT Male x 1-1/2\ NST (NH) Male Brass Hexagonal Nipple Fitting Fire Equipment Hex Nipple Doule Male Fire Hose Adapter

  • ⚒【PREMIUM MATERIAL】- Made of brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability. The Fire Equipment Hexagonal Nipple Fitting offer long-term service.
  • ⚒【CONNECTION SIZE】- Hex nipple fitting 1-1/2" NH/NST to 1-1/2" NPT double male fire hose adapter. Male 1-1/2 inch NH / NST will only connect to a female 1 1/2 inch NH / NST.
  • Male 1-1/2 inch NPT will only connect to a female 1-1/2 inch NPT/NPSH.
  • ⚒【UNIQUE DESIGN】- With hexagonal section in the middle for an increased bearing surface when adjusting the fitting with a wrench. Hex tube fitting as a short length of pipe with threaded ends for connecting threaded pipes.
  • ⚒【WIDE APPLICATION】- Male to male adapters are used to bridge two female hose, pipe or valve fittings. Suitable for use in general firefighting applications. Brass fire hydrant adapter fittings are used for connecting fire hose, PVC pipe, and other low-pressure pipes in the fire brigade, industry, refinery, building industry, agriculture, shipping, military, and civil protection.
  • ⚒【100% SATISFACTION SERVICE】-We have a professional product development team. If you have any questions about compatibility or any dissatisfaction, please feel free to contact us and we will help you ....
Check Stock

Class A Customs | 20 Gallon RV Concession Fresh Water Tank with Plumbing Kit & 12 Volt Water Pump | T-2000-BPK-PUMP

  • 20 Gallon Fresh Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe WATER TANK MEASUREMENTS: 32.5” Longest Length (not including fittings) x 11.75” x 11.75” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
  • TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
  • NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
  • BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe Thread PVC Male Adaptor (ONE) 5ft. Section of 0.5....
Check Stock