ReviewsFlow Meter Gauge

Alemite GREASE GUN, CORDLESS 20V (596-B (qty 1-9))

Lcd with real-time information, including grease meter, cartridge level, and charger capacity gauge.
Patented airflow management optimizes motor and transmission life.
Cartridges per charge - 23 at high speed/ 24 at low speed.

Check Stock

Kemimoto ATV Fuel Gauge Meter Compatible with Yamaha Gas Gauge Grizzly 600, Big Bear, Kodiak 400 Gas Tank Fuel Cap Replacement # 4SH-24260-11-00, 4SH-24261-00-00, 5GH-24260-11-00, 5GH-24260-10-00

Kemimoto Gauge Meter can precisely show the remaining oil volume. Just take a glance at the fuel dial to know how much oil left, instead of unscrewing the whole fuel gauge and getting your hand dirty..
ATV Fuel Gauge Meter can measure the amount of remaining oil in real time. With its help, you can monitor the oil volume in a convienent and accurate way, avoiding falling into the insufficient oil quantity trouble cause miscalculate the oil volume outdoors..
Kemimoto Fuel Gauge Meter is designed with rubber seal and retainer. The seal precisely fit with the fuel tank port, preventing oil and smell leaking. The retainer tightly cover the ATV meter to make sure it won’t come loose. No oil leaking or unpleasant smells from your fuel tank destroy your good mood on journey anymore..
Kemimoto Gauge Meter is made of gasoline-friendly steel. It won’t pollute your oil. Moreover, the meter has heat resistance. Even working in high temperature environment for a long time, it still can maintain great performance. We believe that both performance and quality are indispensable. We spare no effort to making every money you spend on our products worthwhile..
Kemimoto ATV Fuel Gauge Meter is compatible with: 2000- 2012 BIG BEAR 400.

Check Stock

AWLOLWA Argon CO2 Mig Tig Flow meter Welding Weld Regulator Gauge Gas Welder CGA-580 With 80'' (6.6FT) Hose

INLET - CGA580 Bottle Connection for argon and argon, CO2, and helium blend bottles.
OUTPUT - Female 9/16" x 18 nut and male 5/"8 UNF-18RH fitting.
The Square flow tube reads from 0 - 60 CFH ,which is indicated by a ball which moves up and down in the flow tube.And has large 1 1/2" diameter pressure gauge which reads from 0 - 4000 PSI. Easy to Read, Accurate.
100% HIGH QUALITY AND STURDY - Flowmeter regulator is made of high quality brass and came with 6.6 Ft argon regulator Hose.

Check Stock

HighFree Argon Regulator TIG Welder MIG Welding CO2 Flowmeter 10 to 60 CFH - 0 to 4000 psi Pressure Gauge CGA580 Inlet Connection Gas Welder Welding Regulator

▶Flowmeter which is perfect for Mig and Tig Welding. Flow Meters,it fit argon ,co2 and argon/co2 fixed. Inlet connection:CGA580..
▶ Compatiblewith a range of gases, including CO2 as well as argon, and designed to reduce and control pressure levels, this MIG/TIG Welding Argon Regulator really is a must-have for any welder..
▶For convenience, the regulator is equipped with a high pressure weld gauge that allows you to view how much gas is left in the tank, while the ergonomic flow meter can be adjusted for different uses. Applicable for many kinds of gases, such as CO2, argon, etc..
▶ It can screw right into the Argon, Argon/CO2, and Helium Tanks. The Square flow tube reads from 0 - 50 CFH and has large 1 1/2" diameter pressure gauge which reads from 0 - 4000 PSI, so you know how much is left in your tank..
▶ Package include: A Flowmeter with 6.5 foot Hose. Applicable for many kinds of gases, such as CO2, argon, etc..

Check Stock

Grow Crew Hydroponic CO2 Enrichment Kit | Includes 20 lb Aluminum CO2 Tank, Carbon Accelerator C02 Regulator, Atlas 7 CO2 PPM Monitor and Active Air Rain System to Shower Your Plants with CO2

✓ BUNDLE INCLUDES - 20 lb. Aluminum CO2 Tank (Empty), Carbon Accelerator CO2 Regulator w/ Flow Meter, Atlas 7 CO2 Monitor, Active Air CO2 Rain System - 20 ft, 6 eye-screws,1 T-Fitting, and a "Legalize Tomatoes" Sticker.
✓ PERFECT CO2 ENRICHMENT KIT - The C02 Rain System showers your plants with CO2! Just affix the eye screws in the ceiling, slide the black laser drilled tubing through the eye screws, attach the plastic tubing from your CO2 Regulator and you've got CO2 raining down on your plants!.
✓ CARBON ACCELERATOR REGULATOR W/ FLOW METER - The CO2 Release Kit provides you with the tools you need for proper CO2 enrichment. The regulator assembly features an industrial-grade 120-volt solenoid valve with 6 ft. power cord, a precise flow-gauge, and easy-to-read pressure gauge. The kit also includes 10 ft of tubing for dispersal, and connects directly to 20 lb. or 50 lb. tanks..
✓ TITAN CONTROLS ATLAS 7 CO2 PPM MONITOR - Select CO2 PPM levels at 1000 PPM, 1250 PPM or 1500 PPM. Integrated photocell. Built-in calibration feature. Single button control. Enclosure resists dust, rust, and moisture. 5 Amps maximum/120 Volts/60 Hz..
✓ 20 LB. ALUMINUM CO2 TANK - The 20 pound aluminum tank is brand new, and perfect for use with our CO2 regulator. Aluminu....

Check Stock

CGOLDENWALL Turbine Flow Meter Fuel Meter Digital Flowmeter with FNPT Thread, Flow Meter for Water Diesel Kerosene Gasoline, Flow Rate Range 2.5-26GPM (1 inch Flow Meter)

FLOW METER: Before use, please calibrate the flow meter with the liquid to be tested. And the flow rate of the liquid should exceed 2.5 gallons per minute, if the flow rate is too slow, the flow meter cannot measure normally. There is no battery included..
MULTI-FUNCTION DISPLAY: High-definition LCD display, can read single cumulative flow, instantaneous flow and total cumulative flow. The clear function can clear the value of cumulative flow, to make sure it is always within the measuring range. If your flow meter cannot work, please contact us in time..
HIGH-QUALITY MATERIALS: The aluminum alloy housing is sturdy, durable and corrosion-resistant, which have a long service time. The PCB circuit board make the battery have a long service life, and safe in use. Please NOTE: the LCD display is not water proof.
INSTALLATION: The flowmeter can be installed in horizontal and vertical directions, but the flow direction of the liquid needs to be consistent with the direction of the arrow on the flowmeter. There is no direction requirements for the installation of the display screen..
MEASURABLE LIQUIDS: The turbine flow meter can used for measuring the water, gasoline, diesel, kerosene, methanol and other low-corrosive, non-viscosity liquids..

Check Stock

CGOLDENWALL Turbine Flow Meter Digital Fuel Flowmeter with FNPT Inlet/Outlet, 1inch Flow Meter for Water Diesel Kerosene Gasoline, 2.5-26GPM /9-100LPM (1 inch)

FLOW METER: the 1 inch flow meter can read instantaneous flow rate, single cumulative flow and total cumulative flows. But it has minimum flow rate requirment, if the flow rate of the tested liquid is lower than 2.5 gal/min, the readings will be inaccurate..
TECHNICAL PARAMETERS：① diameter of water inlet: 32mm.
③ the flow speed requirenment for tested liquid: 2.5~26 gal/min.
⑥ max temp of tested liquid: 158°F/70°C.
MULTIPLE UNITS: the flow meter provide 4 meauring units for option, which are liter, gallon, pint and quart. The unit defaults to gallons, if the unit is not gallons, please refer to the user manual to change the unit to the needed one..
NOT WATER PROOF: the flow meter is not water proof, please keep the display from water during use, to avoid chip damage. We upgraded The flowmeter has been upgraded from never-sleep model to auto-sleep model, which automatically dims the screen when no liquid is flowing through it..
WIDE APPLICATION: The turbine flow meter can used for measuring the water, gasoline, diesel, kerosene, methanol and other low-corrosive, non-viscosity liquids. If there is any problem, please contact us in time..

Check Stock

Bestarc Argon/CO2 Mig Tig Flow Meter Gas Regulator Gauge Argon Gas Welding AGR-2

Argon / CO2 regulator and flow meter, suitable for most argon tanks, argon hose for Miller, Lincoln, Hobart, HTP, and most other welders.
The material of body is quality brass. Sturdy and durable.
Easy to use, gas regulator can be directly screwed into argon or argon / CO2 tank, ideal choice for MIG TIG welding, chemical and electronics industry.
Accurate to read, pressure gauge reads from 0 - 3500 PSI, and the square flow tube reads from 0-25 CFH.
We provide high quality products at fair price, one year warranty, professional after-sales service.

Check Stock

MEANLIN MEASURE Argon Regulator Flow Meter with 6.5 Feet Hose,CGA580 Inlet Connection,5/8' x 18RH Outlet Fitting,Dual Output Argon Welding Flowmeter for TIG MIG Welder

【Easy to Read】2″ gauges for easy reading. Makes adjusting your pressure values a piece of cake..
【CGA-580 Inlet】This Gas Pressure Regulator Can Be Used with Argon, Helium and CO2 Gas Tanks,Ideal for MIG and TIG welding applications..
【Accurate Measurement】This Gauge measuring range 0-4500PSI,It has a highly sensitive pointer to sense the pressure in the pressure tank,so it is more reliable than the flow-gauge style..
【Excellent Quality】Our Double Dutput Argon Regulator Is Made Of Brass For High Strength, Toughness And Corrosion Resistance For Long Term Use..
【Package Include】1*Argon Regulator Flow Meter 1* 6.5Feet Hose 2*Male 5/”8 UNF-18RH Fitting 2*1/4″ Hose Barb Adapter 2*Female 9/16″x18 Nut.

Check Stock

CGA580 Argon CO2 Regulators Argon Gauges Gas Welding Regulator Compatible with Mig Tig Miller Lincoln Weld 0-4500PSI / 0-10BAR - CO2 Argon Regulator with 6.6Ft Hose

Universal Gas Welding Regulator - This Gas Pressure Regulator/Flowmeter Can Be Used with Argon, Helium and CO2 Gas Tanks (CGA-580 Inlet). Argon gauge 0 to 4500 PSI, argon gauge regulator provides accurate regulation of gas flow. This Gas Hose Is Ideal For Fitting Mig And Tig Welding. Ideal for commercial, industrial and laboratory applications.
100% Brand New Argon Regulator with Hose - The CO2 regulator body is made of brass, Single-stage regulator, built-in pressure overload automatic degassing device. Large T-shaped adjustment handle, easy to adjust the pressure by hand. The flow tube is made of polycarbonate.
Accurate Argon Regulator with Pressure Gauge - CGA580 fitting (15/16" Male Thread), 9/16" male thread, 5/8" female thread. Argon gas meter measuring range: 0 to 4500 PSI. Argon CO2 Regulators Gauges Gas Welding Regulator With 6.6Ft Gas Hose. 6.6Ft Hose Quick Connect Fitting enable your tanks at a safe distance from your welding projects.
Reliable CGA580 Argon CO2 Regulator - The Argon CO2 flowmeter regulator has a plastic adjustment knob that allows for smooth "light touch" flow settings and has an internal safety relief design, Provides a safe environment for car driving. CO2 regulator with 2" dual gauges that will be easy to read.

Check Stock

VIVOSUN Argon/CO2 Regulator Emitter System with 50 PSI Fixed Max 4000PSI Inlet Pressure Precise Brass Regulator for Gas Control in Hydroponic Grow Tent House Aquarium Welding

Durable Material: This regulator’s body is made of high-quality brass, which has high strength, high toughness and corrosion resistance, and strictly tested to ensure long -term use.
Precise Control and Measurement: This regulator equipped with a flow meter and pressure gauge.
Output flow is indicated by a ball in the flow tube and is adjustable from 10 to 60 SCFH.
The pressure gauge ranges from 0 to 4000 PSI and is used to read the amount of gas remaining in the tank.
CGA-580 Tank Inlet: The regulator fits standard Argon and CO2 gas tanks with CGA-580 inlet connection, and has a unique filter port design on the CGA-580 mounting port.
Two Connection Ways: There are female 5/8" x 18 outlet nut and a standard 1/4" barb adapter, you can choose the connection method of the hose according to your needs.
Multiple Applications: Suitable for indoor grow rooms, grow tents, greenhouses and hydroponics to increase CO2 in the growth environment for optimal growth.
And ideal for MIG TIG welding, chemical, and electronics industries.

Check Stock