ReviewsFulton Sheen Books

The Delight And Dilemma Of Female-To-Male Transgender

Fits all Fulton jacks, originally equipped with a 6 inch plastic wheel, except TJD125 and TJD103.
Fulton Service Kit - 6 inch plastic replacement wheel.

Fulton F2 Jack Adapter Plate allows you to upgrade from a Fulton Center-Bolt Swivel Mount Jack to an F2 Series Marine and Recreational Jack.
Fits Fulton's patented center-bolt design - used on XP10 and XP15 weld-on jacks.
Heavy-duty, cast aluminum mount is tapered, moving wheel closer to center line of trailer frame to optimize castering performance.
installs easily - no drilling or welding required.
All necessary mounting hardware and complete installation instructions included.

...p mitered corners then you know what kind of a challenge it can be to say the least. You could always try those large, cumbersome and very expensive parallel clamps to try and work each corner just right to hold your mitered corners together. That too can be extremely challenging and not to mention very costly..
The Fulton Miter Spring Clamps are the ideal and cost effective way to quickly and easily clamp mitered corners without all of the hassle you typically have with other clamps. The Spring Miter Clamps are made from a high strength steel. The clamps can be applied using your hand to squeeze the clamp to open the sharp, pointed tips or you can use the Miter Spring Pliers to make it super easy to to spread the tips apart..
Once you have the clamp tips spread apart, simply place the spring clamp onto the mitered corner you need to secure, then release the clamp so the tips pierce into the wood and keep your stock in place. Depending on the size of your project, you may need to use more than one spring clamp on each corner to hold your stock in place..
Unlike other available spring clamps, the Fulton Miter Spring Clamps don’t cut into your stock piece. The uniquely designed tips are designed to pierce the wood so that there is minimal visible eviden....

Applying veneer, laminate or even wall coverings usually requires some tools that you may not find in your neighborhood big box store or even at a local mom and pop hardware store. The Fulton J-Roller is one of those items and is the ideal tool for applying pressure to your sheet or paper goods to ensure proper adhesion to your work surface..
When applying veneer on wood for example, you generally need to exert a good amount of even downward pressure on the veneer sheet or roll. To do this, we could use a flat bar of some sort, but that generally won’t be even enough and can’t get into the slight undulations of the wood surface. The Fulton J-Roller is the perfect width to properly work the veneer for proper adhesion..
A full 12” long, the J-Roller is the perfect length to handle most any project where you need to apply sheet goods to another surface. The roller is made from a firm, non-marring, textured rubber material that helps you apply pressure where it is needed. The roller wall is about 3/8” thick so it will stand up to the rigorous chore of applying pressure to your sheet goods..
The heavy duty steel handle is designed to help you exert as much pressure as possible to the work surface. The handle is wrapped with two separate sec....

Applying veneer, laminate or even wall coverings usually requires some tools that you may not find in your neighborhood big box store or even at a local mom and pop hardware store. The Fulton J-Roller is one of those items and is the ideal tool for applying pressure to your sheet or paper goods to ensure proper adhesion to your work surface..
When applying veneer on wood for example, you generally need to exert a good amount of even downward pressure on the veneer sheet or roll. To do this, we could use a flat bar of some sort, but that generally won’t be even enough and can’t get into the slight undulations of the wood surface. The Fulton J-Roller is the perfect width to properly work the veneer for proper adhesion..
A full 12” long, the J-Roller is the perfect length to handle most any project where you need to apply sheet goods to another surface. The roller is made from a firm, non-marring, textured rubber material that helps you apply pressure where it is needed. The roller wall is about 3/8” thick so it will stand up to the rigorous chore of applying pressure to your sheet goods..
The heavy duty steel handle is designed to help you exert as much pressure as possible to the work surface. The handle is wrapped with two separate sec....