ReviewsGear Oil Bevel Gear

Makita 5477NB 15 Amp 7-1/4" Hypoid Saw

Efficient hypoid gears deliver more power and greater surface contact than conventional worm drive gears..
Powerful 15 AMP motor for increased productivity..
Oil bath technology and sealed gear housing for less maintenance..
0º – 51.5º bevel capacity with positive stops at 45º and 51.5º is ideal for truss and rafter cut-outs..
High quality, heat treated hypoid gears are engineered for long lasting performance..

The Gear Package included: spindle, single/double crown gear, pulley, rack, bevel gear, copper gear, bushings, axles, tires, rubber bands and so on, more accessories that you need for diy toy cars/robots/motors..
Axle length of 30mm, 50mm, 70mm, 100mm, shaft diameter is 2mm, 2pcs / kind, for a total of 8 Pcs.
Five wheel wheels: outer diameter 30mm, inner hole 2mmfor a total of 4 Pcs.
The characteristics of gear: 36MM yellow 2mm hole belt wheel, rack, four-wheel drive, 28 tooth 2mm hole Fan teeth and 30-100mm gear axle, five wheel wheel diameter 30mm!Multi-uses, you can use it to fix the toys,Great for diy science and small production, product design and mechanical model..
Most gear is 2mm aperture (tight or loose), in addition to one 81.5A spindle hole is 1.5mm, there are 2 crown is 2.5mm, there are 1 crown gear C303A is 3mm, one 15 teeth 2.3mm hole and 3.17mm hole..

36 teeth for use with G485Y-P mating bevel gear in 2:1 gear ratio applications.
Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
Brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability.
Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.

32 teeth for use with L149Y-P mating bevel gear in 2:1 gear ratio applications.
Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.

16 teeth for use with PA4416Y-G mating bevel gear in 4:1 gear ratio applications.
Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.

VARIETY OF GEARS, This 78 pcs gear package includes: axles, tires, gears, bushings, rack, etc, so basically buy back can always be used. Enough for you to choose and durable for use..
MORE COMPREHENSIVE THINGS , spindle, single, double, crown gear, pulley, rack, bevel gear, copper gear, axle, axles, tires, rubber bands and so on..
USED FOR DIY, The gears set is good accessories for your toy car , robot and so on, Easy to change when the gear is missing or damaged, as a spare accessory to use..
MADE OF HIGH QUALITY PLASTIC, wearable and long service life. Small parts, easy to use..
SATISFACTION GUARANTEE, We care for every customers feeling.If this product does not meet or exceed your expectations,please send it back for a 100% refund no questions asked..

30 teeth for use with L153Y-P mating bevel gear in 1.5:1 gear ratio applications.
Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.

10 teeth for use with L147Y-G mating bevel gear in 2:1 gear ratio applications.
Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.

18 teeth for use with L152BY-G mating bevel gear in 2:1 gear ratio applications.
Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.

12 teeth for use with HL148Y-G mating bevel gear in 2:1 gear ratio applications.
Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
Case-hardened teeth for applications where hardness and strength are needed to transmit torque and motion.

Efficient hypoid gears deliver more power and greater surface contact than conventional worm drive gears..
Powerful 15 AMP motor for increased productivity..
Oil bath technology and sealed gear housing for less maintenance..
0º - 51.5º bevel capacity with positive stops at 45º and 51.5º is ideal for truss and rafter cut-outs..
High quality, heat treated hypoid gears are engineered for long lasting performance..