ReviewsGpio Interfaces

REXQualis RPi GPIO Status LED & Terminal Block Breakout Board HAT for Raspberry Pi A+ 3A+ B+ 2B 3B 3B+ 4B

  • The item has been soldered and assembled. Support for Raspberry Pi A+ 3A+ B+ 2B 3B 3B+ 4B.
  • GPIO status LED and power 5V / 3.3V indication. GPIO output or input level high LED on, output or input level low LED off. 5V blue, 3.3V red, GPIOs green. The position of the LED is in a one-to-one correspondence with the position of the Raspberry Pi 2x20pin connector, and the logic level of the GPIO can be observed very quickly and intuitively. The driving current of each LED is only 0.1mA, so you don't have to worry about it affecting the read and write status of GPIO..
Check Stock

kuman RPi GPIO Breakout Expansion Board + Ribbon Cable + Assembled T Type GPIO Adapter 20cm FC40 40pin Flat Ribbon Cable for Raspberry Pi 3 2 Model B & B+ SC05

  • Assembled RPI GPIO with 8" 40 pin ribbon cable for Raspberry Pi 3B, Raspberry Pi 2 model B, Raspberry Pi 1B+, Raspberry Pi 1a+, Raspberry Pi zero w, Raspberry Pi zero.
  • 40 pins are labeled for easy prototyping.
  • Gpio adapter plus for Raspberry Pi B+, Raspberry Pi 2, Raspberry Pi is not included.
Check Stock

Treedix 3pcs GPIO Reference Board Pinout Plus for Raspberry Pi A+, B+, 2, 3, 4

  • This reference board is a very convenient tool to determine the position and function of each pin, which can make it very easy to connect the wire to the Raspberry Pi GPIO.
  • One side of the reference board shows the position, and the other side shows the GPIO number. You can view all the different pin labels of the 2×20 GPIO connector on the Raspberry Pi. By placing it on the connector or next to it, you can quickly check if any wires or components are properly connected.
  • Material: Raspberry Pi GPIO Plus reference pinout is made of glass fiber, and the holes of the reference plate are gold-plated Length: 60.2 /2.37in, width: 20.1mm/0.79in 100% high quality..
  • Use this reference guide to easily connect wires and components to your Raspberry Pi.
  • Compatible with Raspberry Pi models A+, B+, 2, 3 and 4.
Check Stock

Ingcool Raspberry Pi Pico Microcontroller Board with Pre-soldered Header Low-Cost, High-Performance,Based on RP2040 Chip, Dual-core Arm Cortex M0+ Processor,Flexible Clock Running up to 133 MHz

  • Raspberry Pi Pico is a low-cost, high-performance microcontroller board with flexible digital interfaces..
  • Raspberry Pi Pico Board incorporates Raspberry Pi's own RP2040 microcontroller chip, with dual-core Arm Cortex M0+ processor running up to 133 MHz, embedded 264KB of SRAM and 2MB of on-board Flash memory, as well as 26x multi-function GPIO pins..
  • For software development, either Raspberry Pi's C/C++ SDK, or the MicroPython is available..
  • There're also complete development resources and tutorials to help you get started easily, and integrate it into end products quickly..
  • This is a Raspberry Pi Pico with Pre-soldered Header,it is easier to connect with another items..
Check Stock

GPIO Status LED Terminal Block Breakout Board for Raspberry Pi A+ 3A+ B+ 2B 3B 3B+ 4B

  • GPIO status LED and power 5V / 3.3V indication..
  • GPIO output or input level high LED on, output or input level low LED off. 5V blue, 3.3V red, GPIOs green. The position of the LED is in a one-to-one correspondence with the position of the Raspberry Pi 2x20pin connector, and the logic level of the GPIO can be observed very quickly and intuitively. The driving current of each LED is only 0.1mA, so you don't have to worry about it affecting the read and write status of GPIO..
  • Support for Raspberry Pi A+, 3A+, B+, 2B, 3B, 3B+, 4B.
  • Terminal block pitch 3.5mm, wire size range 26AWG to 16AWG, strip length 5mm, screw M2 steel, pin header and cage copper. 2 x 20 pins expansion pin header, height 8mm..
  • Packing list: 1x terminal block breakout module, 4x M2.5x16mm nylon standoffs, 4x M2.5x6mm nylon standoffs, 4x M2.5 nylon nuts(NOTE: the item not include Raspberry Pi module).
Check Stock

sb components Raspberry Pi Pico GPIO Expansion Board, Multi-Purpose GPIO Expansion for Raspberry Pi Pico

  • Raspberry Pi Pico GPIO Expansion Board is used to break out all the pins and power of the Raspberry Pi Pico development board via male or female headers.
  • Pico GPIO Expansion Board allows the user to connect it to other components with the help of a jumper wire.
  • It has been designed to enhance the learning experience for the user.
  • GPIO Expansion Board is specifically made to work with the Raspberry Pi Pico Board.
  • Compatible with all the variants of Sensors/Modules.
Check Stock

sb components Raspberry Pi Pico Board with Raspberry Pi Pico GPIO Expansion Board, Multi-Purpose Raspberry Pi Pico Kit

  • Raspberry Pi Pico is Raspberry Pi's first microcontroller board, designed especially for physical computing.
  • It can be easily reprogrammed over USB from a Raspberry Pi or other computer using the C/C++ SDK or the official MicroPython port.
  • Raspberry Pi Pico GPIO Expansion Board is used to break outall the pins and power of the Raspberry Pi Pico development board via male or female headers.
  • Raspberry Pi Pico GPIO Expansion Board allows the user to connect it to other components with the help of a jumper wire.
  • Raspberry Pi GPIO Expansion Board is specially made to work with the Raspberry Pi Pico Board.
Check Stock

MakerFocus Raspberry Pi 3 Case Protective Case, Raspberry Pi 3.5 inch Display Case, with Mini Cooling Fan for Raspberry Pi 3B, 3B+,2B,2B+ Compatible with Raspberry Pi GPIO 3.5 inch Display

  • Installation instructions video: Please get the link from the product description below. PLZ NOTE: ★This case is not compatible with 3.5 Inch HDMI TFT LCD Display, It is designed to RPI 3.5 Inch GPIO Display, ★The 3.5 inch screen is not included!!!.
  • Dual-use: You can use it only on the Raspberry Pi motherboard, or use it on the Raspberry Pi motherboard and Raspberry Pi 3.5inch display,Then decide whether to cover the its cover. (Note: The Raspberry Pi motherboard and Raspberry Pi 3.5inch display are not included!!!).
  • Can install mini cooling fan: The case when used without the display screen, you can install mini cooling fan, Snap-in installation, the cooling fan was included in packaging..
  • With GPIO open position: There is a GPIO open position on this case cover,when you use it only with Raspberry Pi motherboard, it can easy to pull up and insert the GPIO pins, don't need to open the cover. This case is easy to install and has good ventilation..
  • With cable guide hole: It reserved cable guide hole for the camera, more convenient to use with camera.
Check Stock

Orange Pi 5 8GB Rockchip RK3588S 8 Core 64 Bit Single Board Computer, 2.4GHz Frequency Open Source Development Board Mini PC Desktop Run Orange Pi OS, Android12, Debian11 (Pi 5 8GB)

  • Orange Pi 5 uses Rockchip RK3588S new generation 8-core 64-bit processor, quad-core A76+quad-core A55, with 8nm process design, up to 2.4GHz main frequency, integrated ARM Mali-G610 GPU, embedded high-performance 3D/2D image acceleration module, built-in NPU with 6Tops computing power, with 8GB (LPDDR4/4x), and up to 8K display processing capability..
  • Orange Pi 5 Single Board Computer provides abundant interfaces, including HDMI output, GPIO interface, M.2 PCIe2.0, Type-C, Gigabit LAN port, 2*USB2.0, 1*USB3.0, etc..
  • Orange Pi 5 microcontroller open source board mini computer can be widely used in tablets, edge computing, artificial intelligence, cloud computing, AR/VR, intelligent security, smart home and other fields, covering AIoT various industries..
  • Orange Pi 5 Mini PC supports Orange Pi OS, the official operating system developed by Orange Pi, as well as Android12 and Debian11..
  • Orange Pi Single Board Computers can builed a computer, a wireless server, Games, music and sounds, HD video, a speaker, Android, Scratch.Pretty much anything else, because Orange Pi is open source..
Check Stock

Geniatech XPI-3128 Single Board Computer,Embedded Computer Module,Development Board ,Rockchip RK3128 Quad Core Cortex-A7 8GB WiFi ,Card-Sized High Performance Board

  • 85mm*56mm, Credit-card-sized High Performance Board.
  • 4*USB HOST, 1*HDMI Out, 1*Micro USB, 1*UART, 1*GPIO interface, WiFi and 100M LAN interface,Support Micro SD card.
  • Rockchip RK3128 with Quad-core Cortex-A7 up to 1.2GHz.
  • 40 Pin header enables hardware re-use by maintaining compatible alternate pin functions like I2S, I2C, PWM, UART, and GPIO. Form-factor compatible with Raspberry Pi 3 for easy migration..
  • Form Factor & GPIO Compatibility with Raspberry Pi for Maximum Re-usability.
Check Stock

Banana Pi BPI-M5 Amlogic S905X3 Single Board Computer with LPDDR4 4GB RAM and 16GB eMMC Storage for AIOT Support Android Debian Raspbian Armbian

  • [High Performance Processor] Amlogic S905X3 quad-core Cortex-A55 processor (2.0GHz).
  • 16GB eMMC onboard storage ---- MicroSD slot with support for up to 256GB expansion.
  • [4K Smart Home Audio and Video chip] Adopt quad-core 64-bit ARM-A55 architecture CPU chips, integrate G31 graphics processor, support 4K video decoding and 4K video output.
  • [SDK and Various System Operation Support] Banana Pi M5 support multiple various OS, like Android 9, and Raspbian and Linux system, as well as third party image Odroid Android image.
  • [Multifunction Interfaces] 4 x USB 3.0 ports.
  • Power Source: 5 volts at 3 amps via micro USB (TYPE C).
  • [Wifi & BT support via expansion board] BPI M5 support SDIO interface Wifi&BT, you can buy the WiFi&BT board, 802.11 a/b/g/n/ac 2T2R WiFi and Bluetooth 5.0..
  • [Wiki] https://wiki.banana-pi.org/Banana_Pi_BPI-M5.
  • If you have any after-sales problems, please contact monica @ smartfire.cn. Click "WayPonDEV" and ask a question or leave the message in our forum at "forum.youyeetoo .com/"..
Check Stock