ReviewsH bridge Motor Driver

ACEIRMC 8pcs L298N Motor Driver Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power MEGA R3 Mega2560

When you are driving voltage (above logo for the 12 v input, can actually accept input range is 7 to 12 v) for 7 v to 12 v, can make to onboard power supply 5 v logic, when using the onboard after 5 v power supply, interface of + 5 v The power supply does not input voltage, but can yield 5V voltage for external use..
The chip manual proposes to support 35V, but according to the book When the maximum voltage is applied to the maximum voltage of 298 conservative applications to 24V, for example, the motor with a rated voltage of 18V shall be driven.
Great for for Arduino DIY Smart Car Robot Power MEGA R3 Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits.
No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use.
Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient.

Check Stock

SB New Motorshield for Raspberry Pi 3,2,1 and Zero This Expansion Board can Control up to 4 Motors or 2 Stepper Motor, 2 IR sensors and a Single ultrasonic Sensor.

Dual H-Bridge IC L293D. Motor Input Supply Range: 6V - 24V.
Single Motor Output Current: 600mA or 1A peak per channel.
On board Arrow Indicator for motor direction Indication,.
2 IR sensor connectors with 3.3V level output protection. Control 2 stepper motor.

Check Stock

HiLetgo 4pcs L298N Motor Driver Controller Board Module Stepper Motor DC Dual H-Bridge for Arduino Smart Car Power UNO MEGA R3 Mega2560

L298N as main driver chip makes strong driving ability/small heating/strong anti-interference/low calorific value.
Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability.
Dual-channel H-bridge driver working mode creates higher working efficiency.
To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.
Large capacity filter capacitance, afterflow protection diode, more stable and reliable.

Check Stock

RATTMMOTOR 400W Blushless CNC Air Cooled Spindle Motor ER8 12000RPM + 600W Blushless Spindle Motor Driver LCD Panel without Hall + 55mm Clamp Mount for CNC Router Milling Machine

【Brussless Spindle Motor】Power: 400W.
Note: Please see clearly that this spindle motor output shaft is with ER8 collet,and output shaft is complete shaft, can't be exchanged to ER11, ER16....
【Brussless Spindle Motor Driver】Maximum driver power: 600W.
Maximum driver motor running speed: 12000R/Min.
Brushless spindle driver（Model Name: NVBDL）is specialized for the ecomomic engraving machine,it matchs with the brushless DC motor. With the....
The users can take down the panel from the main driver and install it on the controller cabinet.By the panel,you can set the parameter,control motor....

Check Stock

Shredneck TREMPACK 2

Includes Shredneck TremBlock & TremTool 2.
On some Edge Bridges the TremBlock can be used to hold the bridge in an "UP" position to aid in string changing.
TremTool 2 includes 3.0mm Hex for String Locks screws, Locking Nuts, Bridge Height adjustment & 2.0mm Hex for intonations adjustment.
TremTool 2 inlcudes mm Hex Includes Standard & Phillips Head Reversible Driver bit for general adjustments.

Check Stock

JUKI MO-6714S Industrial 4-Thread Overlock Sewing Machine

✅Thank you! see below full info. on this machine,--- Get your sewing job done real fast with the Juki DDL-8700H sewing machine that can do up to 5500 stitches per minute. This Juki sewing machine has a large 11-inch arm space that lets you work with even large quilts. The stitch length of this 5500 SPM sewing machine goes up to 5mm which gives you a lot of freedom in doing your job..
✅The sewing machine complies with the "Juki Group Green Procurement Guidelines" on the use of hazardous substances, will be delivered in 3 boxes. 1) machine head, & some accessories* 2) servo motor & v belt 3) table top/legs/drawer/*2 spool-Thread Stand Bobbin Winder Oil Pan/Knee Lifter 1 Bobbins 1 Needles Instruction Manual Screw Driver Machine Oil 2-Euro Hinges & 2 Euro Rubber Mounts Table Rest Pin Safety Belt Guard.
✅1) machine head, & some accessories* 2) servo motor & v belt 3) table top/legs/drawer/*2 spool-Thread Stand Bobbin Winder Oil Pan/Knee Lifter 1 Bobbins 1 Needles Instruction Manual Screw Driver Machine Oil 2-Euro Hinges & 2 Euro Rubber Mounts Table Rest Pin Safety Belt Guard.

Check Stock

MKS SERVO42C NEMA17 Closed Loop Stepper Motor Driver Low Noise for CNC 3D Printer Prevent Losing Steps Compatible with Gen L SGen L SKR 2 / V1.4 Turbo BTT Octopus V1.1 Mainboard

...you can connect the computer by serial port, for parameter adjustment and query..
Position /speed/torque closed-loop, it can run at high speed without losing step. Easy to install and wire. The max printing speed can reach 150-180mm/S. Field-Oriented control, low noise, low vibration and low calorific. 4 Half bridge driver with 8 MOSFET, high operating efficiency. 14Bits magnetic encoder, high angle resolution..
Compatible with Gen L SGen L, SKR 2 / V1.4 Turbo BTT Octopus V1.1 Motherboard and other board which is seperated with drivers, that means drivers is not soldered onto the board.
Package: 1*MKS SERVO42C(include motor) + 1*Adapter board(MKS APT) + 1*60cm 6pin Data Cable . (User method, please check the links from the following description).

Check Stock

GeeekPi 5 Pack Geared Stepper Motor 28BYJ-48 5V Stepper Motor + Uln2003 Motor Driver Board + Dupont Wire Jumper Wires Ribbon Cables Compatible with Arduino

5pcs Stepper motor and driver board compatible with arduinoIDE 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi..
Stepper motor with a standard interface could be connected with Driver Board easily.
A, B, C, D four-phase LED indicates the status of the stepper motor work..
5 line 4 phase can be used for ordinary ULN2003 chip driver, connect to the 2 phase , support the development board, with convenient use, direct docking..
Package Includes:5 x Stepper Motor,5 x ULN2003AN Driver Board,30 x Female-to-female jump wire.

Check Stock

3 Axis CNC Kit Nema23 Stepper Motor Dual Shaft 425oz-in 112mm 3A & Driver 40VDC 4A 128 microstep for CNC Router Milling Engraving Machine

♞【Product】3 Axis nema23 stepper motor driver usbcnc controller kit.
♞【Nema 23 Stepper Motor】 Nema 23 Stepper Motor / Holding Torque: 425oz-in,280Ncm / Motor Size:57x57x112mm / Phase:2 / 4pcs lead wire / 1.8 Step.
♞【Stepper Motor Driver】FMD2740C Stepper Motor Driver / 4Amps / Support voltages:12 to 50V DC / 128microstep.
♞【4 Axis USBCNC breakout board】 Come with Hand Control with USB Cable / Only support USBCNC software / input voltage: 15-36V DC..
♞【DC Power Supply】400W 36V 11A DC Switching power supply.

Check Stock

RIDGID 18V Brushless 1/2" High Torque Hammer Drill/Driver

Drill/Driver: All Metal Gears For extended durability.
Drill/Driver: 24 Position Clutch Ring For ultimate precision when driving.
Impact Driver: Quick-Release Hex Collet Spring ejection for easy loading and removal.
Impact Driver: High Torque Output 0 - 1,800 in-lbs. of Torque.
Brushless Motor Technology Delivers more runtime, more power, and longer motor life.

Check Stock

Shengmilo-MX02S 26 * 4.0inch Fat tire Electric Bicycle, 1000W Motor, Shimano derailleur, Snow Mountain Bike, 48V*17ah Removable Lithium Battery, Dual Hydraulic Disc Brake, Smart LCD Display

...-50km battery range.❸Manual Mode:Pedal the Bicycle Normally as You Would Any Bicycle..
【Fat Tire】 MX02S Is Equipped With 26 Inches 4.0 Fat Tire, Which Can Adapt To Snow, city road，Beach And Mountain Rides. The Bike Frame Is Made Of Aluminum Alloy 6601 , Recommended Driver Height: 165 Cm - 200CM, Maximum Weight Support: 180 Kg..
【WARRANTY REGULATIONS】Frame warranty:12 Months. Motor and Battery warranty: 6 Months. Other parts warranty: 12 Months. 95% pre-assembled when you get the bike..

Check Stock