ReviewsHall Effect Sensor

Ecosmart FSA QC MEDLRG ECO 24 Replacement Part

ACS723 AC DC current sensor with OPA344 OpAmp.
Measure both AC and DC currents from 10mA up to 5A.
Capable of 80KHz bandwidth. Fixed to 20KHz on board. JP1 can be closed to enable all 80KHz.

This product is a current detection module, mainly using the ACS758-LCB current sensor. The ACS758 consists of a precision, low-offset linear Hall sensor circuit with a copper current path close to the wafer. The current applied through the copper current path is capable of generating a magnetic field that can be induced by the integrated Hall IC and converted to a proportional voltage.003cbr003e.
Device accuracy is optimized by placing the magnetic signal close to the Hall sensor. The accurate, proportional output voltage is provided by a stable chopper-type, low-bias BiCMOS Hall IC that is factory-precisely programmed.003cbr003e.
The internal resistance of this conduction path is typically 100 μΩ with low power loss. The thickness of the copper wire allows the device to operate under high overcurrent conditions. The terminals of the conduction path are electrically isolated from the sensor pins (pins 1 to 3). In this way, the ACS758 sensor IC family can be used in applications that require electrical insulation without the use of opto-insulators or other expensive insulation techniques.003cbr003e.
Perform RC filtering on the output and use the op amp to build a voltage follower circuit to make the output more stable and better match the impedance of....

Backlit 3.2”, 320x240 display screen with multiple color palette choices and user customizable colors.
Wi-Fi connectivity for easy product registration and firmware updates.
Superb ergonomics including smooth Hall-effect sensor gimbals.
Smart Technology compatibility out of the box.
3.7V 6000mAh 1S Lithium Ion transmitter battery and a magnetic USB Cable and Micro USB Adapter for convenient USB charging.

【Perfect Combination】Using this product can measure both voltage and current, very suitable for DIY electronic design projects..
【Current Sensor Module】Chip: ACS712ELC-30A.
Pin 5V power supply, on-board power indicator.
The module can measure positive and negative current of 30 amperes, corresponding to analog output of 66mV/A..
【Voltage Sensor Module】Voltage input range: DC0-25V.
DC input connector: Terminal cathode connected to VCC, GND negative pole.
Output interface: "+" then 5/3.3V, "-" then GND, "s" then the for Arduino AD pins..
【Package Included】2 x ACS712 Hall Effect Current Sensor Module + 2 x Voltage Sensor Module DC0-25V Voltage Tester Terminal Sensor.

48V 1500W Powerful brushless gearless motor with 34mph (54km/h) speed.
Restricted to 750W and 24mph (38km/h) speed by default as a road-legal pedal electric hub bike kit.
Dual Mode Controller: Motor works under Hall effect and non-Hall effect, extend life for electric bike..
LCD display shows battery level and pedal assistance settings.
Brake Levers cut off the power supply to the motor safely.
Twist throttle has battery level display.
Comes with all the components you need to a full conversion, including Rear Wheel(of 7 speed sprocket), Motor Controller, Controller Bag, Pedal Assist Crank Sensor, Cable Ties & Plastic Coil, Twist Throttle, One Pair of Brake Handles, Manual, LCD Meter. (Note: Battery not included).
48 Volt electrokinetic cell battery with a nominal capacity not less than 11.6Ah is required..

48V 1000W Powerful brushless gearless motor with 28mph (45km/h) speed.
Restricted to 750W and 24mph (38km/h) speed by default as a road-legal pedal bike conversion kit..
Dual Mode Controller: Motor works under Hall effect and non-Hall effect, extend life for electric bike ebike conversion kit..
LCD display shows battery level and pedal assistance settings.
Brake Levers cut off the power supply to the motor safely.
Twist throttle has battery level display.
Comes with all the components you need to a full conversion, including Rear Wheel(of 7 speed sprocket), Motor Controller, Controller Bag, Pedal Assist Crank Sensor, Cable Ties & Plastic Coil, Twist Throttle, One Pair of Brake Handles, Manual, LCD Meter. (Note: Battery not included).
48 Volt electrokinetic cell battery with a nominal capacity not less than 11.6Ah is required..