ReviewsHand Held Circular Saws

Delta Diamond Ripper Pro Premium 4 Inch X .500 Tuck Point Diamond Blade, 1/2 Inch Width, Mortar Removal, Grout Repair, Masonry, & Concrete Surfaces (4\ X .500)

FAST & EFFICENT MORTAR REMOVAL - Eat old mortar out fast with high cutting performance and long life..
PREMIUM DIAMOND CONCENTRATION - Higher levels of diamond concentration than standard blades give the best performance to cost per cut..
WET OR DRY - Use wet or dry for mortar removal, grout repair or preparing masonry and concrete surfaces..
SPECIFICATIONS - 4" X .500" wide, have a 7/8" arbor with a 5/8" bushing and will work with most hand-held grinders and circular saws. The maximum safe operating speed is 15,200 rpm..
LIFETIME WARRANTY & FREE RETURN SHIPPING - All Delta Diamond Products, Inc Diamond Blades, Coring Bits, Hole Saws and Grinding Wheels include a lifetime warranty against warping, cracking and material defects. If any diamond tool (being used under its intended use with at least 50% wear left) fails to cut or work properly, or if the bond between the diamond segment and the steel core becomes separated at any time, the diamond tool will be replaced free of charge..

Rigid aluminum straight edge guide with 36-inch capacity for making straight and accurate cuts.
The saw guide works with most circular saws to help keep your saw straight to make accurate cuts.
Fits right and left handed circular saws.
Saw guide fits right handed and left handed circular saws.

...ing life and provide a low cost per cut..
DEEP U GULLETS - This unique segment/keyslot design allows for better air cooling and chip deflection resulting in better performance..
SPECIFICATIONS - 8" diameter X .090 thick with a diamond-7/8" arbor. Also included is a 5/8" bushing. Fits most hand-held angle grinders and circular saws. Heat-treated high-speed steel core is guaranteed to withstand the demands of dry cutting. Expected blade life is approximately 4,000 inch feet (one inch foot = 12" length X 1" depth). The recommended operating speed is 4,500 rpm..
LIFETIME WARRANTY & FREE RETURN SHIPPING - All Delta Diamond Products, Inc Diamond Blades, Coring Bits, Hole Saws and Grinding Wheels include a lifetime warranty against warping, cracking and material defects. If any diamond tool (being used under its intended use with at least 50% wear left) fails to cut or work properly, or if the bond between the diamond segment and the steel core becomes separated at any time, the diamond tool will be replaced free of charge..

Saw Blades Specifications - 5-4/5" Ultra-thin kerf Wood Cutting Circular Saw Blade for fast cutting, Teeth: 52T, Diameter: 5-4/5"/ 147mm, Arbor: 4/5"(20mm), HI-Density Carbide Tip for Maximum Performance.
MAX RPM - 10000, Kerf: 0.055"/1.4mm, Hook Angle(forward): 20 Degree, Tooth design: ATB, Fast and Smooth Cuts..
ATB Tooth Design to facilitate splinter discharge and to prevent the saw blade from being blocked by sawdust, make cutting easier. Extra-hard steel blade body - delivers accuracy and resists bending and deflection for true cuts..
Laser cutting Anti-Vibration Slots can drastically reduce vibration and sideways movement during the cutting process, Also help channel heat build-up during the cutting process, allowing the blade to expand and contract, extending the blade life..
Upgraded to Teflon surface coating, strong non-stickiness, lowest friction coefficient, anti-adsorption, high-temperature resistance. Smooth and efficient rotation..
Ideal for ripping and crosscutting on softwood, hardwood, plywood, chipboard with fine finishing, not for metal cutting. Widely use for Circular Saws, Miter Saws, Table Saws, Hand Saws, and Chop Saws, save your time and energy..

Professional quality, construction grade for ripping & crosscutiing of thick hardwoods up to 3 1/2" thick and soft woods up to 1" thick.
For use on Miter Saws, Circular Saws, Table Saws, Hand Saws and Chop Saws. RPM up to 4,000.
Ideal for cutting Hard Wood, Soft Wood, Exotic Wood and Abrasive Wood..
Thin kerf allows a smooth finish w/ minimal waste. Lower hook angle improves the surface quality of the cut, increases the feed pressure required..
3.0 mm kerf design, ATB Grind & 15Degree hook.

【Application】:Fast smooth clean cutting and widely used in Miter Saws, Circular Saws, Table Saws, Hand Saws and Chop Saws..
【ATB Tooth】:Alternate Top Bevel Teeth blade ideal for cutting all kinds of wood.Such as Hard Wood,Soft Wood,Plywood,Chipboard..
【Anti-Kickback Shoulder】:For safety reasons,preventing inversion of saw blade during cutting..
【Specification】:8 inch 64T fine finishing wood cutting blade with a 5/8 inch arbor..
【Good Service】:Please contact us if you have any questions about this saw blade.We guarantee the 100% replacement.Any problems will be solved within 24 hours..

High quality and professional grade for ripping and crosscu tting of thick hardwood to 3-1/2" thick and softwood to 1" thick..
The blades can be used on Circular Saws, Table Saws, Miter Saws, Hand Saws and Chop Saws..
Ideal for cutting hardwood, softwood, exotic wood and abrasive wood..
Thin kerf allwos a smooth finish with minimum waste. Lower hood angle improves the surface quality of the cut and increases the feed pressure..

Includes 24" NGX clamp edge, 25" NGX clamp edge extension with connectors, rip handle, saw plate.
Made of heavy-gauge, rigid aluminum for extreme durability.
For use with circular saws, routers, jig saws, and other portable power tools to achieve track saw like cuts.
Can be used on right- or left-handed circular saws — no tools necessary to switch.

80 teeth saw blade for high cutting speed, high strength, good stability and durability..
Made of high quality high speed steel, ensures stable quality and high efficiency, having stable performance..
Metal circular cutting blade with negative front rake angle design, increase the ability of resisting the tooth edge collapse..
Large high‑hardness cutter head, fine grinding surface, stable body, suitable for cutting hard materials..
Wide application, used for circular saws, miter saws, table saws, radial arm saws, etc..

CONTINUOUS RIM CONFIGURATION – For clean and precise cuts wet cuts of porcelain and stone tiles.
STANDARD CORE DESIGN – Allows contractors to lift tiles to square notches or finish corners.
THIN KERF CORE – Cuts cleanly through dense porcelains but has enough rigidity to prevent blade deflection or curved cuts.
EQUIPMENT – Designed to be used on tile saws, circular saws, and hand saws.

Ultra-thin kerf carbide-tipped design provides smoother cuts with less drag on the motor and minimal material loss.
Carbide tooth construction for clean cuts and long life.
Fully hardened and expertly hand-tensioned steel saw plates for true cuts.
Specially designed for cordless saws to permit more cuts per charge.
For use with 6-1/2" Cordless Circular Saws with 5/8" arbor.