ReviewsHarmonic Balancer Tool

19 mm Harmonic Balancer Socket & 50mm Crankshaft Crank Pulley Wrench Holder for Honda and Acura Engines

【50MM Crankshaft Pulley Removal Tool 】-- Used to maintain the harmonic damper pulley position while removing/installing the pulley bolt on many....
Using 50MM Crankshaft Pulley Removal Tool -- Use with square socket driver. >1/2" square drive use with breaker bar. Hole in center of tool - allows....
【19 MM Harmonic Balancer Socket 】--The hex socket is used with an impact wrench to loosen the crankshaft bolt It can be used on Honda engines that....
Using 19MM Harmonic Balancer Socket -- Use with 1/2" drive.Designed with more than three times the standard socket mass to direct more energy to....
Satisfaction Guarantee: If you're not 100% satisfied with this tool set, simply return it for a full refund in 30 days, guarantee with 12 months’....

Check Stock

A-Team Performance - Harmonic Balancer Install Tool Crank Pulley Installer Crankshaft Installation 551141 Billet - Compatible with GM 1997-Up LS1 LS Engines

Harmonic Balancer Install Tool Crank Pulley Installer Crankshaft Installation 551141 Billet.
Compatible with GM 1997-Up LS1 LS Engines.
Superior Quality: Made of hardened structural 10.9 steel, it is excellent solid and durable with great rust and corrosion resistance to long-lasting service your balancer..
Wide Compatibility: This LS Harmonic balancer is perfect for your Camaro, Corvette, Trans Am, GTO, G8, LS Truck, or LS powered street rod..
Installation: Simply thread the tool into the crankshaft until it seats, then tighten the nut down until the pulley is seated. This is a must have for engine swaps or upgrading the balancer..

Check Stock

VQL Harmonic Balancer Steering Wheel Puller Kit (13 Piece) with Blow-Molded Case Use for Removing Harmonic Balancers, Gear Pulleys, Steering Wheels and Crank Shaft Pulleys

【Widely Used】 Harmonic Balancer Steering Wheel Puller Tool are used to removal of harmonic balancers, gear pulleys, steering wheels and crank shaft pulleys. This is a universal type puller.003c/p003e.
【Durable】 13 Piece Harmonic Balancer Steering Wheel Puller Kit are made of high-quality steel, Drop Forged, Heat Treated, this tool set is very durable.003c/p003e.
【Apply Pressure Evenly】 Yoke allows for either 2 or 3-hole application. The harmonic balancer puller allows uniform pressure on the parts, No need to worry about the steering wheel puller and harmonic puller puller kit will damage the auto parts.003c/p003e.
【Package Included】 1* center screw, 1* Floating swivel, 2* 5/16 x 4 bolts, 2* 1/4 x 3 bolts, 3* 1/4 x 2 bolts, 3* 5/16 x 2 bolts and 1* Blow-molded Case.003c/p003e.
【Various Sizes】 Steering wheel pullers has a caster with four slots for using in nearly any configuration. Various sized provides necessary versatility.003c/p003e Buy with confidence. We provide refund and exchange service, if you have any questions, please feel free to contact us.003c/p003e.

Check Stock

DASBET 46Pcs Harmonic Balancer Puller Set, Steering Wheel Puller, Gear Puller, Crank Shaft Pulley w/Case

【Application】The tool set applies equal pressure to the hub, helping removing harmonic balances, crankshaft pulleys, and steering wheels safely..
【Including】 Package provides everything you need to pull a harmonic balancer, 1 pc- pressure screw.
【Material】Constructed from heat-treated carbon steel for ultimate strength and longevity.
【Easy Storage】The tool set comes in a blow-mold case with handle and latches for secure storage, simple organization and easy transportation..
【Service】If you have any issues with the Harmonic Balancer Puller, please contact customer service for troubleshooting help..

Check Stock

Shorty's Skate Tool The Wench

Fitment: Locks flywheel in place when removing harmonic balancer on 6.6L Duramax engines with Allison automatic transmissions..
Function: Saves time by locking the flywheel at the transmission instead of having to remove the starter for water pump replacement..
Duramax 2500 / 3500 Pickups (Toothed pieces only): Removes metal spring-loaded inspection plate on the bottom of the transmission. Tool should slide into opening toward engine with the top of the tool engaging the teeth of the flywheel..
Duramax 4500 / 5500 Trucks (Toothed pieces with screws): Remove the rubber inspection cap on the bottom of the transmission. Insert the tool at the front of the opening to engage the flywheel and hand tighten bolt to hold tool in place..
36mm 12-point Socket: Use with 3/4" square drive to remove harmonic balancer bolt and retorque on installation. 36mm 12 point socket can also be used on axle..

Check Stock

SEEBOO LS Harmonic Balancer Installation Tool Crank Pulley Install Tool Compatible with GM 1997-UP V8 LS1 LS2 LS3 LS4 LSX LSA LS6 LQ4 LQ9 with Thrust Bearing & Wrench Flats

【HIGH PERFORMANCE】—The Crank Strength Of The Harmonic Balancer Installation Tool Is 12.9, And It Is Made Of High-Quality 35CrMo Heavy Steel. The Quenching Process Is Modulated To Ensure That It Does Not Affect Long-Term Use. The Surface Is Black And Rust-Proof. There is No Need To Worry About The Wrench Slipping Off During The Installation Process With Customized Flange Nuts!.
【COMPATIBLE WITH CHEVROLET GM LS & LT SERIES 】—Harmonic Balancer Installation Tool Suitable For Camaro, Corvette, Trans Am, GTO, G8, LS Truck Or LS Power Road Signs. Compatible With All GM LS And LT Series Engines From 1997 To The Present (Third, Fourth And Fifth Generations). You Can Also Search For Matching Models Through Amazon To Purchase!.
【 INSTALLATION AND REMOVAL 】— Can Be Screwed Completely Into The Crank, Just Slowly Twist The Nut Until The Pulley Is In Place. The Upgraded Wrench Plane Is Convenient For Disassembly Without Worry，This Is Required For Engine Replacement Or Balancer Upgrades. A Little Lubricating Oil Will Make It Smoother When Using!.
【 PACKAGE INCLUDES 】— 1*Stud, 2*Washer, 1*Thrust Bearing, 1*F....

Check Stock

Bolaxin Flywheel Locking Tool with 36mm 3/4 Inch Wench for 6.6L Duramax Engine

Locks Flywheel in Place When Removing Harmonic Balancer on 6.6L Duramax Engines with Allison Automatic Transmissions.
Saves time by locking the flywheel at the transmission instead of having to remove the starter for water pump replacement.
Use 36mm 12-point socket with 3/4 square drive to remove harmonic balancer bolt and retorque on installation.
Duramax 2500 / 3500 Pickups – Use toothed pieces only removes metal spring-loaded inspection plate on the bottom of the transmission. Tool should slide into opening toward engine with the top of the tool engaging the teeth of the flywheel..
Duramax 4500 / 5500 Trucks -- Use toothed pieces with screws remove the rubber inspection cap on the bottom of the transmission. Insert the tool at the front of the opening to engage the flywheel and hand tighten bolt to hold tool in place..

Check Stock

For GM LS Harmonic Balancer Puller 25264 Crank Pulley Puller Automotive Replacement Engine Quickly Removes Harmonic Balancers without Tapped Holes

【Compatibility】Compatible with GM engine models: 5.3L, 5.7 LS1, 6.0 LS2, 6.2 LS3, 7.0L , compatible with Chrysler,Dodge,Jeep engine models: 3.5 L V6, 3.6L V6, 4.7 L V8, 5.7 L V8, 6.1 L V8. Not applicable to 1997 or earlier general LT (5.7L LT1003c4) series engines (threaded holes), not applicable to 2018 and newer Coyote balancers..
【Unique Design】 The harmonic balancer puller adopts a "clamp-in" design, which can be disassembled without connecting the puller bolts to the balancer, which helps removing the balancer quickly and easily..
【Material】Constructed from high quality carbon steel material , it is solid, durable and no deformation .The surface is coated with black paint, which can resist corrosion and rust, ensures long-term service..
【Benefits】When this harmonic balancer pullers (without threaded holes) is working on the balancer, it do not require disassembly of the radiator. This is a unique design of buckle attachment that can be disassembled without fixing the tie rod to the balancer..
【Satisfaction Guarantee】If you're not 100% satisfied with this tool set , simply return it for a full refund in 30 days, guarantee with 12 months’ warranty..

Check Stock

BETOOLL 19 mm Harmonic Balancer Socket & 50mm Crankshaft Crank Pulley Wrench Holder Tool Removal Holding Spanner kit Compatible with Honda and Acura Engines

50mm Crankshaft Pulley Removal Tool: Used to maintain the harmonic damper pulley position and prevent it from rotaing as you install or remove many Acura and Honda engine crank bolts..
Using of 50mm Tool: Works with a 1/2 inch breaker bar or ratchet. Small compact and center hollow design, the crankshaft pulley wrench gets into tight engine spaces easily when servicing the engine and powertrain..
19mm Harmonic Balancer Socket: BETOOLL socket could be used on Honda engines that use a 19mm hex pulley damper bolt or other 19mm applications..
Using of 19mm Tool: Used with 1/2” square drive. This Harmonic Balancer Socket features a deep counter-weighted design to increase torque, so you could quickly and easily break stubborn bolts loose..
Tough and Sturdy: Made of high strength alloy steel,heavy duty and durable.Coated with black paint which prevention corrosion. Backed by a lifetime replacement guarantee..

Check Stock

Crank Pulley Puller, GM Harmonic Balancer Puller Automotive Replacement Engine Harmonic Balancers without Tapped Holes

Damper Remover Puller is designed to Remove Harmonic Balancers without Tapped Holes,Time Saving Tool - No Need to Remove Radiator..
Fit: Applicable to General Motors engine models: 5. 3 L, 5. 7LS1, 6. 0 LS2, 6. 2 LS3, 7. 0 L, and Engine models compatible for Chrysler/Dodge: 3.5 L V6, 3.6L V6, 4.7 L V8, 5.7 L V8, 6.1 L V8..
Not Fit: Not applicable to 1997 or earlier GM LT (5.7L LT1<4) series engines (with threaded holes), and will not work with 2018 and newer Coyote balancers..
Time-saving tools: No need to disassemble the radiator, unique snap-on accessories, allowing removal without bolting the puller to the balancer. Harden and temper. Make it easy to remove the damper..
Advantages: The design can be disassembled without disassembling the radiator when disassembling the harmonic balancer without threaded holes, and can be disassembled without connecting the puller bolts to the balancer..

Check Stock

Michigan Motorsports Harmonic Damper Balancer Crank Bolt for GM LS7 & Dry Sump LS3 Engines LS9 LT4 LT5 11570163 Install Tool LS1 LT1 Pulley Installation

Michigan Motorsports Harmonic Damper Balancer Crank Bolt for GM LS7 & Dry Sump LS3 Engines LS9 LT4 LT5 11570163.
Factory Replacement Harmonic Balancer /Dampener Bolt for GM LS7 and LS3 Engines using a dry sump oiling system. Also known as a Crank Pulley Bolt or Engine Crankshaft Pulley Bolt..
Harmonic balancer bolts are made of high-quality steel and are heat-treated for extra strength. The factory LS series engines harmonic balancer bolts are a torque to yield design. Not reusable..

Check Stock