ReviewsHeader Roll

TWOPAGES Liz Linen Curtain Linen Drapery Panel for Living Room Bedroom Patio Door (Custom)

FABRIC: Sold per panel, not a pair. 80% Polyester, 20% Linen. Heavyweight 350 gsm faux linen material. Skin-friendly, excellent colorfastness..
WIDTH: For pleated, goblet header, panel width is the width that pleats are already set, we recommend fullness ratio 1.0 time wide of your curtain rod or track. For tab top and rod pocket header, we recommend fullness ratio 1.2-1.5 times wide of your curtain rod. For grommet header, we recommend fullness ratio 1.5-2 times to create the waves and folds when close the curtains. For flat hook and back tab header, we recommend fullness ratio 1.25-2 times wide of your curtain rod..
LENGTH: For grommet, rod pocket, back tab and tab top header, measure from the top of rod to where you want the bottom of the drapery to be (1/2" above the floor, or approximately 6" to 8" below the window sill ). This is your finished top of pole to hem drop. For flat hook, pinch pleat and goblet header, measure from ring eyelets to the floor. Subtract 1/2" to get the panel length you need..
Fit for living room, bedroom, patio door, club, kitchen, hospital, room divider..
Machine washable for the unlined, white darkening or 90% blackout lining, in cold water and gentle circle. Dry clean suggested for privacy or thermal blackout l....

...ATA 6Gb/s connectors. 4 x SATA 3Gb/s connectors. Support for RAID 0, RAID 1, RAID 5, and RAID 10..
USB: Up to 10 USB 2.0/1.1 ports. Up to 4 USB 3.0/2.0 ports..
Internal I/O Connectors: 1 x 24-pin ATX main power connector/1 x 4-pin ATX 12V power connector/2 x SATA 6Gb/s connectors/4 x SATA 3Gb/s connectors/1 x CPU fan header/2 x system fan headers/1 x front panel header/1 x front panel audio header/1 x S/PDIF Out header/1 x USB 3.0/2.0 header/3 x USB 2.0/1.1 headers/1 x serial port header/1 x parallel port/1 x Trusted Platform Module (TPM) header/1 x Clear CMOS jumper.
Back Panel Connectors: 1 x PS/2 keyboard/mouse port/1 x D-Sub port/1 x DVI-D port/1 x HDMI port/2 x USB 3.0/2.0 ports/4 x USB 2.0/1.1 ports/1 x RJ-45 port/3 x audio jacks.

1/16" x 2" x 50' Roll black fiberglass exhaust heat wrap wiht locking ties(pack of 15) + 2in Hose Clamps..
Fiberglass exhaust header wrap can create more horsepower and reduce under hood temperatures a realistic 50% ..
Durable, tight woven, easy heat shield insulation .Protect the hose of the engine system and also Protects drivers and mechanics from burns..
Read the instruction first when start to wrap it ,Wrap headers to protect plug wires,downpipes to increase velocity, motorcycle pipes to prevent leg....
Good for exhaust pipes insulation .Great improving car and motorcycle performance. High resistance to abrasions, oil spills, temperatures and....

Supports all motherboards with USB 3.0/ 3.1 19-pin header.
Motherboard: USB 3.0 Internal 19 Pin MB Male Housing Header.
Front Panel: USB 3.1 A-Key 20 Pin Front Panel Female Header / NOTE: Does not convert from 5GB/s to 10GB/s.
Easy way to access USB-C and support front panel header, doesn't require to have latest motherboard to experience USB-C technology..
** Note on USB current over limit issue: The power from the USB 3.0 header on the motherboard has a power rating at 4.5W (0.9A x 5V). However, many USB-C devices can withdraw power up to 100W (20A x 5V). This may result in a power shut down to protect the motherboard and its components..

USB 3.1 require a different front panel header than USB 3.0.
The USB 3.1 port interface is using the USB 3.0 pin set and more.
It is design to be backwards compatible (will explain later).
There are no official release of the specs for the USB 3.1 header yet (as of this writing), But first motherboard with this is the ASUS ROG MAXIMUS IX....
Connector1: USB 3.0 Front Panel Header. Connector2: USB 3.1 Front Panel Header..

3.00 Inch Header Buddy Collector Kit 3.00 Inlet 2.25 Outlet 3 Bolt Flange Jones.
2 Flanges 2 Collectors and 6 Nuts and Bolts Included.
HEADER BUDDY Is An Innovative, New Design For Header/Exhaust Assembly That Requires NO GASKET.

USB 3.1 Front Panel Header to USB 3.0 Type-A Female Extension Cable 50cm Panel Mount Type Length: 50cm.
USB 3.1 require a different front panel header than USB 3.0..
The USB 3.1 port interface is using the USB 3.0 pin set and more. It is design to be backwards compatible (will explain later). .
There are no official release of the specs for the USB 3.1 header yet (as of this writing), But first motherboard with this is the ASUS ROG MAXIMUS....
Connector1: Type-A USB3.0 Female Connector2: USB 3.1 Front Panel Header.

348 holes of prototyping area, Full breakout of the 40-pin Pi Header.
Holes are connected in row and column groups.
Silkscreen marking for 40-pin Pi Header reference.
High quality HASL PCB finishing, D0.9mm drill holes and D1.9mm pad size.
Pin Headers set: 1 x extra long 40-pin (length: 12mm) stacking header, 1 x short 40-pin (length: 6mm) stacking header.

The cable only support usb3.1/usb3.0 device, it can't work at USB2.0(480Mbps).
USB 3.1 require a different front panel header than USB 3.0. The USB 3.1 port interface is using the USB 3.0 pin set and more. It is design to be backwards compatible (will explain later)..
There are no official release of the specs for the USB 3.1 header yet (as of this writing), But first motherboard with this is the ASUS ROG MAXIMUS IX FORMULA,STRIX Z270I/Z270G etc..
Connector1: USB 3.0 Front Panel Header Connector2: USB 3.1 Front Panel Header.

Fantastic tool and is a ‘must have’ for making custom fabricated tube chassis, roll cages and header/exhaust work.
Works well with 9/16" to 2" O.D. tubing, useful in joining different sized tubing.
Ideal for anything that you need to put an angle onto the end of either round or square tubing for tight notches and perfect fit.
Incorporates and includes a built-in protractor gauge to quickly and easily set the degree angle of the tubing where end matches up to mating tubing.
Takes the challenges and difficulty out of making 40° to 90° angled tubing joints and makes angled tubing joints quickly and accurately.