ReviewsHeavy Load Power Relay

[2 Pack] DC 6-30V Timer Relay Programmable Delay Relay Module Cycle Timer with LCD Display / 5V Micro USB, Smart Home Controller

【Multifunction Timer Relay】Programmable delay modes to control the relay timings, widely used at smart home, industrial control, automatic irrigation, indoor ventilation, protection equipment etc..
【Load Range】Operating voltage: DC 6V - 30V, support micro USB 5V power supply. High level trigger: 3V - 24V. NO(Normally open) maximum load < AC 250V/10A, < DC 30V/10A. Timing range: 0.1s ~ 999mins (continuously adjustable)..
【Reverse Protection】Built-in a diode to provide protection against accidental reverse polarity for the circuits..
【Sleep Mode】If no operation within 5 minutes, the digital tube of the relay board will turn off automatically. Pressing any button can wake it up..
【Parameter Setting】OP(conduction time) / CL(off time) / LOP(circuit times) can be set individually, and the parameters are mutually independent. All parameters are permanently saved once set. The functions and parameters can be reviewed or changed at a later time..

Check Stock

HiLetgo 2pcs 12V Photoresistor Sensor Relay Module Car Light Automatic Control Switch with Cable

Relay working mode: NO(normally open) or NC(normall closed).
Load capacity: AC 0V--250V/10A, DC 0V--30V/10A.
Characteristic: Relay outputing separately.

Check Stock

WOWOONE 30 Types 74HCxx Series Logic IC Assortment Kit, Logic Gates, Integrated Circuits Assortment Kit, TTL, High-Speed Si-Gate CMOS IC, Low-Power

Input point X element x0-x7, DC24 input, low level valid. X0-5 is the high-speed counting input port (default: 12K,100KHZ optional)..
Output analog voltage WR3A instruction, corresponding to the value 0-4095. Intermediate relay M: M0-M3071, the power loss preservation range can be set..
The maximum speed current is 1A. External load common terminating + 24, the other end received the PLC output port Y..
Y0-Y5 is optional relay or transistor output, relay output current 5A. The transistor output DC24V, the current maximum 1A..
100Ms timer: t0-t199, accumulative power off save t184-t199.
10Ms timer: T200-T249, accumulative power off saving T246-T249.
1Ms timer: T250-T383, where T250-255 is cumulative.
16-bit counter: C0-C199, power off to save C100-199.
32-bit counter: C200-C219, power off to save C220-C234.

Check Stock

Vikye Driver Module, 4 in 1 MAX7219 LED Dot Matrix Display Driver Module, Professional MCU Controller DIY Kit

EASY OPERATION: The industrial remote control is 12 button design, which is easy to operate, has complete functions, which is simple and practical..
RELAY LOAD: The maximum load capacity of the relay is 1-110V 5A DC, 85-265V 6A AC, suitable for more industrial control applications..
8 WORKING MODES: The controller has modes including instantaneous, self locking, interlocking, self locking and instantaneous coexistence..
HIGH SENSITIVITY: Remote control distance in open space reaches 300‑500 meter, +20dBm wireless transmission power, high receiving sensitivity..
GOOD ADAPTABILITY: The rolling code coding and decoding type (similar to HCS301) can adapt to up to 32 remote controllers, stable and reliable..

Check Stock

Phase Monitoring Relays JVR800-2 Under Over Voltage Protector, Three-Phase Voltage Monitoring Sequence Protection Relay with

This monitoring relay can monitor own working voltage..
8 kinds of rated voltages are adjustable, can apply to voltages in all regions of the world.
The working status of the relay is indicated by the LED indicator.
Ultra-small size and it is easy to install..
It is applied to mobile device connection control, causing accidents in equipment protection against reverse operation, normal/emergency power switch, preventing phase failure of power load..

Check Stock

Baomain SSR-60DA 60A Solid State Relay Module 4-32VDC / 24-480VAC + Heat Sink

Photocoupler isolation between input control signal and controlled power, isolation surge voltage up to 7500V..
Input signal turn-on voltage DC 3 to 32V, turn-off voltage DC 0 to 0.8V. LED indication for relay turn-on..
Output voltage range: AC 90 to 250V(50/60Hz). Maximum on-state average current 3 Amp. Maximum on-state current 10 Amp (003c 10 seconds). Non repetitive surge peak on-state current: 120 Amp (003c20mS). Load type: General purpose..
This is a simple and practical solid state relay module, which is very convenient to use, for Arduino, Raspberry Pi, ESP32, PLC or other projects. The GPIO of these controllers are directly connected to this relay input to control the mains power, and it is suitable for most loads less than 350 Watts (for 115VAC)/700 Watts (for 230VAC)..
Compact ABS plastic case and wires connect for easy mount. Two screw mounting holes are convenient for you to fix it on the wall or wooden board. Of course, you can also choose not to lock the screw..

Check Stock

KETOTEK KT8230 Digital Temperature Controller Thermostat Regulator 120VAC 30A Fahrenheit -22~572℉ Heating Cooling for Incubator Brooder Refrigerator Fermenter Greenhouse Reptile

【Wide temperature range.】The range for KT8230 is -22~572℉, This is a relay temperature controller, There is no voltage output directly, you need to connect additional power supply for the load, then it can be set by differential (1~80℉) to turn on/off the load, it is like a switch..
【Output is 30A relay, more accurate.】The temperature controller 120V can be used for big power equipment, like incubator, brooder, refrigerator,Fermenter,Greenhouse,etc. 1°F accuracy to keep the temperature in desired range..
【Support delay start function and temperature correction.】The cooler and heater will delay to work if you set the delay time(PL: 0~7min) not 0, You can set depend on what you need. -30.0°F～30.0°F calibrate the temperature when there is error..
【Safe protection.】Temperature Regulator will alarm when it exceed temperature limit or sensor error, alert you when something wrong happened. You can also set the low(LS) and high temperature limit(HS) to change the temperature range, LS < Setting Temperature < HS..
【Simple operation.】 All parameters setting can be saved after restart, you don’t need to set the thermostat regulator when power off, or restart it from vacation. 2m NTC sensor allows more possibility for home.

Check Stock

TWTADE/JQX-62F-2Z Coil Voltage AC 110V 80A DPDT Electronmagnetic Relay,High Power Relay AC 110V

Size (Approx.): 85 x 65 x 65mm/ 3.3" x 2.5" x 2.5"(L*W*H).
Package Content: 1 x High Power Relay + 8 x Terminals.

Check Stock

Yibid LED Integrated Tail Light Replacement for Honda Grom MSX 125 Motorcycle 2014-19, Brake Indicator Sequential Lights for MSX125/SF CBR650F CTX700 CTX700N, Smoke len with 1pcs 2-Pin Flasher Relay

...016 , CB 650 F 2014 - 2015, HONDA CBR 650 F 2014-2015 , HONDA CTX 700 N 2013 - 2015.
for ‘17-18’ Compatibility with/Replacement for Honda Grom Please check your taillights bucket and the lisitng picture（4&5）,Some bikes may not the perfect fitment need to modify!!!.
Note！！LED light usually use little bit power, sometimes after you install, the LED light blink so fast or not blink, if you have this issue, you may need LOAD RESISTOR to put between the LED lights and POSITIVE, usually go around 6 ohm LOAD RESISTOR will,make it work, however we do not carry any load resistors,please purchase if necessary.

Check Stock

SSR-100, DC-DC Solid State Relay 5-220V DC with Non-Contact Switch, SSR-100 DD

Control Method: The solid state relay uses DC-DC control method, which can provide stable performance..
Load Current: 100A, Load Voltage: 5-220VDC, Control Voltage: 3-32VDC, Control Current: DC: 5-50mA.
Installation: The solid state relay uses bolted installation method, easy to install and remove..
Heat Dissipation: The relay has pure aluminum heat sink base plate for fast heat dissipation..
Material: The solid state relay is made of thyristor and optoelectronic with non-contact switch..

Check Stock

Three Phase Voltage Monitoring Relay, Three Phase Voltage Small Monitoring Relay Phase Sequence Relay for Mobile Device Connection Control for Mobile Device(M265)

This monitoring relay can monitor own working voltage..
8 kinds of rated voltages are adjustable, can apply to voltages in all regions of the world.
The working status of the relay is indicated by the LED indicator.
Ultra-small size and it is easy to install..
It is applied to mobile device connection control, causing accidents in equipment protection against reverse operation, normal/emergency power switch, preventing phase failure of power load..

Check Stock