ReviewsHigh Power Attenuator

MST VC Low Pass Filter Eurorack Module

Check Stock

Fender Groove Tubes GT-12AT7 Select Amplifier Tube

  • Preserve pumping tube tones at lower volumes.
  • Works on all 8 ohm amps 60 watts or less.
Check Stock

ART ARTcessories Xdirect Professional Active Direct Box

  • Internal 9-volt battery or phantom power.
Check Stock

MIDI Foot ControllerMeloAudio Guitar Floor Multi-Effects Portable USB MIDI Foot Controller with 10 Foot Switches2 Expression Pedal Jacks and 8 Host Presets

  • High quality Electronic components and circuit design keep your tone clear and pure. Keep the dynamics and tone of your amps sweet spot at lower levels..
  • True bypass. Running through the FX loop and controlling the amount of signal sent to the power section. Let you really push the front end of your amp for the natural feel and tone..
  • Easy-to-use passive attenuator. Passive design doesnt require any power. The LED only displays whether the pedal is on or not..
  • Set output level to minimum immediately by tapping MINIMUM footswitch On board knobs and switch provide flexible sound character..
  • DC 9V Adapter power supply. (plug polarity is positive on the barrel and negative in the center).(NOT INCLUDED).
Check Stock

YDELEKS 50pcs Gold Plated Brass tag Board Turrets Posts Lugs FOR Tube Guitar Amp DIY

  • Preserve pumping tube tones at lower volumes.
  • Works on all 8 ohm amps 60 watts or less.
Check Stock

Hantek 20:1 Passive Attenuator for Pico 300v Max 10Mhz Passive Oscilloscope Signal Attenuator for Automotive Diagnostics Use,HT201

  • The HT201 has been designed to allow fuel injector and primary ignition waveforms to be measured using Hantek oscilloscope products..
  • Please note this attenuator should not be used for any high voltage measurements other than fuel injectors and primary ignition..
  • Passive attenuator with 20:1 attenuation, if input a 20V signal, it can output a 1V signal.Because the signal is attenuated, by using this item, oscilloscope can measure voltage higher than its range(±20V).
  • 【What you will get】 1 x HT201 Signal Attenuation.
  • 【Please Note】 After receiving the product, please check whether it is damaged. If you have any questions, please contact us in time. This product is a consumable and needs to be replaced regularly. Once the product is used, the warranty is not allowed..
Check Stock

Whistler TRX-1 Handheld Digital Scanner Radio

  • Simple Zip Code programming. Preloaded USA/Canada MicroSD card included. Easy updating via Internet. User upgradable CPU firmware. Spectrum Sweeper.....
  • APCO P25 Digital Phase I & II.SYSTEM REQUIREMENTS: Only for use on Windows Operating Systems. CTCSS and DCS subaudible decoder. Dedicated....
  • Dedicated SKYWARN/Weather button. IF Discriminator Out. Tuning Steps: 2.5, 3.125, 5, 6.25, 7.5, 8.33, 10, 12.5 ad 25 kHz. Record up to 50 hours of....
  • The scanner does not function.Ensure that the scanner is equipped with fresh batteries. If powering the scanner from external power, make certain that....
  • Strong signal overload from nearby transmitter.Check performance with and without attenuator activated, use setting with best reception. Loose or....
Check Stock

Vega Barebones - Ultra Low-Noise Variable Gain Amplifier VGA Module for RF & Software Defined Radio SDR Highly Linear & Wideband 30MHz-4000MHz Frequency Capability w/Bias Tee & USB Power Options

  • A wideband (30MHz-4000MHz), high-performance, general purpose LNA module with a built-in variable attenuator to maximize usability and portability.
  • The attenuation can be controlled either with the on-board potentiometer (analog control) or push button array (digital control).
  • Dual amplifier design with adjustable gain (20dB-50dB at 100MHz), low noise figure and low power consumption. Can be powered through bias tee....
  • Made in North America. Full 1 year warranty!.
Check Stock

1pc PE4302 Numerical Control Attenuator Parallel Immediate Mode 1MHz~4GHz, Program Control Gain Attenuation Range is from 0 to 31.5DB

  • This is a PE4302 numerical control RF attenuator module.
  • The parallel immediate mode is simple and easy to use.
  • Bandwidth is wide and can be 1MHz to 4GHz.
  • Program control gain attenuation range is from 0 to 31.5DB.
  • The module supports parallel port and serial port mode as well as power on state selection function.
Check Stock

Behringer MONITOR1 Premium Passive Stereo Monitor and Volume Controller

  • Premium passive stereo volume controller and attenuator.
  • Active-free circuitry guarantees purest signal path.
  • Large Volume knob for extremely precise level adjustments.
  • 2 high-quality XLR combo inputs and 3.5 mm (1/8”) stereo input perfectly connect to your DAW.
  • 2 high-quality XLR outputs and 3.5 mm (1/8”) stereo output to connect to your studio monitors.
Check Stock

SaferCCTV 0.2 Db 950-2150MHz Range SF-95 Satellite Finder Meter for Directv

  • 2. 0.2 dB difference in 950 - 2150MHz range.
  • 3. LNB to REC connectors with a dB level control.
  • 4. With LNB/LNB higher than 60 dB, use a 5dB attenuator.
Check Stock