ReviewsHigh Voltage Xlpe

HEATIT JHSF 80-feet 120V Self Regulating Pre-assembled Pipe Heating Cable

... inch thick insulation material is recommended, especially for extremely cold weather..
ETL approved. 2 ft 18/3 cold lead with plug. Industrial grade heat shrinkage tube for connection.The lowest installation temperature of this heating cable is -10 degree C. Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable.
Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. Four year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we’ll try our best to solve your issue.

Check Stock

HEATIT JHSF 24-feet 120V Self Regulating Pre-assembled Pipe Heating Cable

...commended, especially for extremely cold weather..
ETL approved. 2 ft 18/3 cold lead with plug. Industrial grade heat shrinkage tube for connection.The lowest installation temperature of this heating cable is -10 degree C. The minimum bending radius is 1 inch.Tough XLPE as inner insulation and weather resistant PE (high-low temperature) as out jacket. Ingress Protection 65. Durable.
Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. Four year limited warranty. If you are not completely satisfied with HEATIT heating cable, please feel free to contact us in any time, we’ll try our best to solve your issue.

Check Stock

DEWENWILS Roof Heat Cable, 6ft Heat Tape for Pipe, Gutter, Roof, Self-Regulating Cable Pre-Assembled, UL Listed

...sy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid..
Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket..
Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8'' and less than 1 1/2'' in. diameter. No crossing. No spiral. No overlap itself. Only straight..
Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don't plug in the cable for a long time for testing. When you feel the slight warm, please turn it off..

Check Stock

Qmark WHT500 Utility Heater for Use in Well Houses, Utility Rooms, and Areas with Pipes and Machinery, 500 Watt, 240 Volt, Beige

...sy to install and use. 120 volt, 7 watts/ft. Built in thermostat to turn the cable 37F on 50F off. Energy saving. 100% screen rate with the Aluminum foil and tinned copper braid..
Both CSA and ETL approved. Industrial grade heat shrinkage tube for connection. Tough XLPE as inner insulation and weather resistant PVC (high-low temperature) as out jacket..
Maximum 1/2 in fiberglass insulation was used over the heating cable for lower temperature protection. Pipes must be at least 3 feet and at least 3/8'' and less than 1 1/2'' in. diameter. No crossing. No spiral. No overlap itself. Only straight..
Testing the cable before the installation. Uncoil the cable, plug in the heating cable and then put the thermostat part of the cable into an ice bucket for few minutes. When the temperature is below 37F, the thermostat will energize the cable to work. Normally you can feel the slight warm on the heating cable in few minutes. To avoid the overheat, please don't plug in the cable for a long time for testing. When you feel the slight warm, please turn it off..

Check Stock

3pcs High Voltage Generator DC 6-12V to 1000kV Boost Step-Up Inverter Arc Pulse Generator Power Module High Voltage Transformer (1000 KV)

High Voltage Generator:Input Voltage: DC 6V to 12 V.
High Voltage Generator Cables: Output Cable Length: About 100mm.
Input Cable Length: About 100mm(Red is Positive).
High Efficiency: Voltage Generator Modules are Made of a High-Voltage Transformer Through a Circuit of Components and Using the Principle of Tesla Coils , Output High Voltage Pulse,High Efficiency.
Easy to Connect:High Voltage Generator come with Input and Output Cables and the Peripheral Circuit is Simple,Just Connect the Cable with the Switch and Battery and the Discharge Intensity is Great.
Wide Application: High Voltage Generator Can Be Used for Student Science Experiments, Electronic Instruments,Anion Generators,Science Small Productions and etc..

Check Stock

DC High Voltage Generator, Generator Electric Arc Module DC3.6V/4.8V/6V/12V High Voltage Pulse Generator DC 3kV-11kV Super Electric Arc Module for Nebulizers,Electric Guns

PORTABLE AND EASY TO USE --- The high voltage transformer generator is small, lightweight and portable.
EASY TO USE --- The high voltage generator installation and operation process is very simple, its peripheral circuit is very simple, you only need to connect the switch and battery. You don't have to worry about not using it at all.
INPUT VOLTAGE --- The high-voltage arc generator can output high-voltage current, with small size and high efficiency. The input voltage is DC3.6V/4.8V/6V/12V and will output DC3kV-11kV high voltage.
WIDE APPLICATION --- The High Voltage P-ulse Generator can be used for electric gun salute, gas stove, etc.
GOOD PERFORMANCE --- This module is the finished module of the high-voltage negative ion generator with the help of high-voltage current output and boost power supply module.

Check Stock

[2 Pack] DC-DC 5A Buck Converter 4-38V to 1.25-36V Step-Down Voltage Regulator High Power Module with LED Display

【High Precision】The buck converter consists of 36u thickened circuit boards, high-Q inductance with output LED indicator, and superior solid-state capacitors that can effectively filter out high frequency noise. Suitable for various electronic projects..
【Input Voltage】DC 4V to 38V (input voltage must be 1.5V higher than the output voltage, no boost)..
【Output Voltage】DC 1.25V to 36V voltage is continuously adjustable, maximum output current is 5A..
【Mini Size】62*38*14 mm (with potentiometer). 2 sets included..
【Easy to DIY】Connect to power source, using a mini screwdriver to increase or decrease output voltage by adjusting the screw on the blue potentiometer and monitor voltage with multimeter to get the needed voltage, clockwise to step up voltage and counterclockwise to step-down voltage. (Factory default stays a high voltage, you need to contrarotate about 7-15 circles before the voltage starts ramping down, 1 circle means +/- 1V).

Check Stock

Valefod 10 Pack DC to DC High Efficiency Voltage Regulator 3.2-35V to 1.25-30V Buck Converter DIY Power Supply Step-Down Module

【High Precision】The buck converter consists of 36u thickened circuit boards, high-Q inductance with output LED indicator, and superior solid-state capacitors that can effectively filter out high frequency noise. Suitable for various electronic projects..
【Input Voltage】DC 3.2V to 35V (input voltage must be 1.5V higher than the output voltage, no boost)..
【Output Voltage】DC 1.25V to 30V voltage is continuously adjustable, maximum output current is 3A..
【Mini Size】45 * 23 * 14 mm (with potentiometer). 10pcs included..
【Easy to DIY】Connect to power source, using a mini screwdriver to increase or decrease output voltage by adjusting the screw on the blue potentiometer and monitor voltage with multimeter to get the needed voltage, clockwise to step up voltage and counterclockwise to step-down voltage. (Factory default stays a high voltage, you need to contrarotate about 7-15 circles before the voltage starts ramping down, 1 circle means +/- 1V).

Check Stock

Non-Contact Voltage Tester, Dual Range Voltage Tester AC 12V-1000V/48V-1000V, ENGiNDOT Live/Null Wire Tester, Electrical Tester with LCD Display, Buzzer & Light Alarm, Breakpoint Test (Blue)

【Safety Non-Contact Voltage Tester】Non-Contact Voltage Tester is safer for testing all Electric Appliances in Your Family. The tester with NCV inductive probe for AC voltage Just places the tip near a terminal strip, outlet, or supply cord. When the tip glows red and the pen beeps, you know there's voltage present. The live wire detector can automatically detect the live or neutral wire..
【 High-Efficiency And Convenient 】The tester with LCD display. When the voltage is detected, the alarm will send out green or red light and beep. When the higher the sensed voltage or the closer it is to the voltage source, it beeps at a higher frequency. At the same time, the screen will be red or green, red means the high voltage and live wire are detected, green means the low voltage and null wire are detected..
【DUAL RANGE/ High&Low Sensitivity】The sensitivity/flashlight key can be switched at high and low sensitivity. Detect high and low voltage (AC 12-1000V /48-1000V )Press the S button to adjust sensitivity and adapt low range for doorbells, thermostats, irrigation wiring..
【Multifunction Design 】Use the Non-Contact Voltage Detector in Circuit Breakers, Lighting Fixtures, Switches, Outlets, Wires, and Anywhere You Need it. Bright LED flashli....

Check Stock

Non Contact Voltage Tester Pen, Electrical Tools Electrical Tester AC 12-1000V/48V-1000V, LED Flashlight, Buzzer Alarm for Live/Null Wire Tester Judgment, Wire Breakpoint Finder

【SAFETY FIRST】 : It will send out multiple alarms through sound and light. When the voltage is detected, the tip will send out red light and beep. When the higher the sensed voltage is, or the closer it is to the voltage source, it beeps at a higher frequency. At the same time, the light will be red or yellow, red means high voltage and live wire are detected, yellow means low voltage and null wire are detected..
【Accurately Multi-ranging Measurement】The electrical tester accurately detects AC Voltage ranging from 12V to 1000V, and distinguish them into 2 Voltage levels (low, high). NCV sensitivity automatically adjusts from low and high while indicating Voltage level with audible beep..
【High Efficiency】 Press and hold the switch for two seconds to start the machine, As Long As Voltage is Detected, the Led in the Tester Pen will Shine.
【COMPACT DESIGN】 Bright LED flashlight for work in dim ares.
Low-Power-Indicator when battery voltage is below 2.5V.
Automatic Power Off after 3 minutes without operation or signal detection.
Pocket-sized, pen hook allows you to carry it in your shirt pocket..
【SECURITY LEVEL】 IEC rated CAT III 1000V CAT IV 600V, Meets CE requirements.
The electrical tester is safely double insulated. High Voltage Aler....

Check Stock

Antimicrobial,Yes ADA,110 to 127 VAC,Automatic Hand Dryer

The Airblade V HU02 Sprayed Nickel is available in 2 different voltage options - Low Voltage (100V/120V) and High Voltage (200V-240V) - make voltage selection at checkout.The Airblade V HU02 Sprayed Nickel is available in 2 different voltage options - Low Voltage (100V/120V) and High Voltage (200V-240V) - make voltage selection at checkout..
Airblade V HU02 is 30% quieter (79dB) than the previous generation (Airblade V AB12) -.
The high-speed Airblade V HU02 dries your hands in 12 seconds), but uses less energy than the previous generation (AB12 V) to do so..
The newly redesigned 1000 Watt motor now costs even less to operate.

Check Stock