ReviewsHot Water Boilers

INTBUYING Time Clock Control Valve for Water Filter Softener Resin Tank 9''-11'' Diameter

Widely used in pure water, beverages, boilers, electronics, chemicals, pharmaceuticals and other industries..
This is an automotic control valve in water processing system..
The valve body material is engineering valve body material plastic.
There is a hard water bypass during regeneration, and an external valve is required to block the hard water bypass..

Benchmark temperature stability achieved with an active bypass.
Inlet water filter featuring easy external access.
Concentric up-and-out venting for single boilers and two to four unit single pipe cascades.
Introducing the water heater mobile app for sizing and technical documentation downloads.

...from 104ºF to 572ºF. It is resistant up to 482 ºF when exposed continuously and up to 572 ºF when exposed temporarily heat..
SUGGESTED APPLICATIONS: It can be easily used in sealing the stoves, applications where high heat resistance is required such as heating devices, pumps and motors, chimneys, hot water boilers, electric home appliances, rear main bearing cap split line, automatic transmission pan, case halves and inside cover, damper keyway sealing, differential cover, manifolds, oil pan corner seals, thermostat, transmission pan, valve cover gasket, water pump cover gasket, exhaust manifold & connection points..
PRODUCT FEATURES : It is cured acetoxy system and when cured formation of a flexible silicone gasket can be observed. Excellent bonding to wide range of applications, resists cracking, shrinking and migration caused by thermal cycling, resistance to oil, water & toxic chemicals, pressure resistant, makes air tight & leak proof gaskets in seconds..
EASY TO USE : Waterproof, gasket & seal on most surfaces. Forms to any shape instantly, it will not shrink or crack, high resistance and fast curing properties. It is very resistant to the physical strain after being cured. Superior adhesion & flexibility..

Boiler Rust Inhibitor - Treats 500 to 720 fresh water..
Use in most outdoor wood boilers. Compatible with propylene and ethyelen glycol..
Compatible with Iron, SSTL, Copper, Bronze, and PEX..
Turns the water pink for product residual and leak detection..

WATER HEATER STAND: The Eastman Water Heater Stand safely elevates water heaters and other equipment above the floor to prevent gases and other debris from coming into contact with ignition source.
WHAT IS INCLUDED: This water stand is easy to assemble and includes safety clips to fasten the stand to the wall or floor so that nothing can shake your water heater off its place.
CONSTRUCTION: Made with galvanized steel, this water heater stand is engineered to support water heaters up to 100 gallons.
VERSATILE: This water stand can be installed on concrete or framed walls.
can also support other equipment such as tanks, washers, and boilers.
CERTIFIED: Water heater stands are compliant with Uniform Plumbing Code and International Plumbing Code requirements.

Compatible Models: This silicon nitride igniter compatible with Cook Top and Range, Cook Top, Furnace, Gas Ignition, Hot Surface Igniters, Infrared light source, Warm Air Movement, Pool Heaters and Boilers, Process Machinery, Special FX, Water and Parking Heaters, etc..
Function: When your stove won't light, igniter not glowing, cracked, burned out, cracked, damp, etc., or the igniter has no continuity, the multimeter is not reading or changing small(if the igniter has continuity, then your multimeter should read between 9 - 17 ohms), and you have to replace the nitride igniter.
Materials: Consists of stainless steel 304 bright finish bracket, 1.97" nitride heating element, 1.18" ceramic insulator body, non-glazed 95% aluminia polished finish, 15-3/4" 20AWG/ UL 10362 specification 250°C temperature-resistance cable.
Hot Side Ignitor/Igniter Specification: Rated voltage: AC 120V +/- 10%-15%, 50/60HZ, Cold resistance: 9-17Ω, Rated power: 150W, Temperature at 120v ± 0.5v. 60HZ at 17 sec ≧1180 ℃, Anti-overvoltage ability: igniter energized for 1 minute -132V. Igniter current not allowed to increa....

MAKE ADJUSTMENTS ON-THE-FLY – Want hotter temperature or need to cook it longer? No problem. Simply adjust on-the-fly any time. Starting the cooking....
51 PRE-PROGRAMMED TEMPS - Select from the 6 convenient preset temperature settings or fine tune your own temperature from 100°F to 575°F in 10°F....
SHATTER-PROOF CERAMIC GLASS – There are no open flames or hot coils that can cause burns. Unlike the competition, Gold’s heating surface is....
FAST and EFFICIENT – Gold heats the pot directly transferring 85% to 90% of its electro-magnetic energy to heat energy! Traditional stovetops only....
MELT CHOCOLATE - Mastery of the double boilers is not necessary. Simply set the Gold at 120°F.
add chocolates into an induction-ready pot.

WATER HEATER STAND: The Holdrite QuickStand Water Heater Stand safely elevates water heaters and other equipment above the floor to prevent gases and other debris from coming into contact with ignition source.
WHAT IS INCLUDED: The QuickStand is easy to assemble and includes (2) safety clips and (2) lag bolts.
assembled QuickStand measures 22 inches in diameter by 16 inches in height.
CONSTRUCTION: Made with galvanized steel, this water heater stand is engineered to support water heaters up to 52 gallons.
VERSATILE: This water stand can be installed on concrete or framed walls.
can also support other equipment such as tanks, washers, and boilers.
CERTIFIED: Water heater stands are compliant with Uniform Plumbing Code and International Plumbing Code requirements.

WATER HEATER STAND: The Holdrite QuickStand Water Heater Stand safely elevates water heaters and other equipment above the floor to prevent gases and other debris from coming into contact with ignition source.
WHAT IS INCLUDED: The QuickStand is easy to assemble and includes (2) safety clips and (2) lag bolts.
assembled QuickStand measures 30 inches in diameter by 16 inches in height.
CONSTRUCTION: Made with galvanized steel, this water heater stand is engineered to support water heaters up to 100 gallons.
VERSATILE: This water stand can be installed on concrete or framed walls.
can also support other equipment such as tanks, washers, and boilers.
CERTIFIED: Water heater stands are compliant with Uniform Plumbing Code and International Plumbing Code requirements.

Designed for replacement for V4843/V8843.
Suitable for use on atmospheric boilers, commercial water heaters, and rooftop heaters.
Adj. Range, High Fire-- 3 in. wc to 4.5 in. wc.