ReviewsHss Drill Blanks

5mm Drill bit M35 Specialist Metal Drill Bits, Twist Drill Bit Set, HSS-CO Twist Drill Bit Stainless 1.0-5.0mm for Drilling Stainless Steel Cast Iron Sheet Metal Steel Plate Angle Iron(5mm)

  • [High Hardness]: This 5mm cobalt drill bits sets are made of M35 material and contain 5% cobalt, which effectively improves its hardness and ensures stable performance.
  • [10 Sizes Available]: There are 10 drill bit sizes for this hss drill bit set, and each pack has 10 identical drill bits, you can choose according to your needs.
  • [High Grinding Precision]: This 5mm twist drill high speed steel bit has a high surface finish, which is very suitable for drilling stainless steel, cast iron, sheet metal, steel plate, angle iron.
  • [35-degree Bifurcated Tip]: This 5mm hss high speed m35 cobalt twist drill uses a 135-degree bifurcated tip design, and starts drilling immediately with a small force.
  • [Wide Application]: This 5mm hss drill bit set is sharp and durable, which can be widely used for drilling stainless steel plates, automobile spring steel and die steel.
Check Stock

TOMMARS 35PCS Bolt and Screw Extractor Set incl. Drill Bit Kit Multi-spline & Sprial Extractors Remover Easy Out Tool for Broken Stripped Screws, Studs, Bolts ect.

  • For quickly removing stripped or broken screws, socket screws, studs and broken off bolts without damaging surrounding area..
  • The extractors are made of higher qualilty CR-MO steel, which has high hardness good toughness, higher strength than chrome vanadium steel. The Drill Bits are made of 4241HSS materials. NOTE: drill bits should not be used for stainless steel..
  • Widely Application: Spiral flute extractors for using on common fasteners where lower torque.
  • Multi-spline Extractors for using on higher torque or lower profile tools. HSS Drill Bits for drilling out the interior of the fastener..
  • Set includes: 6 PCS Spiral flute extractors ( 3/32″ to 7/8″).
  • 13 PCS Multi-spline extractors ( 1/8″ to 1/2″ ).
  • 16 PCS HSS drill bits ( 5/64″ to 1/2″).
  • Can be used with electric hand drill, flat or allen wrenches, tap adapters. Must be slow and gentle when used!!!.
Check Stock

Hanson 1765531 Pts Drill Plus Tap Combo 6-32' Number 36 for Tap Die Extraction

  • This tap and drill set contains a convenient HCS tap and HSS drill bit.
  • Self-aligning taps start and thread straight virtually every time.
  • Great for through holes and irregular surfaces.
  • Plug taps are ideal for general purpose threading.
  • Special chip-breaking technology cuts chips easier.
Check Stock

Drill America 5/8'-18 Tap and 37/64' Drill Bit Kit, POU Series

  • Set contains high speed steel plug hand tap and matching high speed steel drill bit.
  • High speed steel plug hand threading tap is popular for use in general machine tapping or cnc tapping.
  • Black oxide drill bit is ideal for production, maintenance or portable drilling jobs.
  • 5/8"-18 hss plug tap and matching 37/64" hss 1/2" shank drill bit in plastic pouch.
Check Stock

JEFE HEX 9-Piece Drill Bits Set-1/16\

  • 【Premium HSS Titanium Coating】High speed steel (HSS) with titanium coating gives Jefe Hex drill bit great durability and prolongs 3 times longer life than drill bits without coating..
  • 【Easy Cut Split Point】Jefe Hex Easy Cut Point design makes drilling easy with less pressure and prevents drill bit walking on the working surface. Fully ground modified parabolic flute design clears chips quickly, decreases friction and heat damage. Tapered web provides durability and reduces breakage..
  • 【Quick Change】1/4" (6.4mm) hex shank fits into standard power tools and impact drivers. Jefe Hex drill bit’s solid bonding technology manufacturing eliminates radial runout and improves concentricity. High torque, impact-rated accuracy..
  • 【Applications】 - Jefe Hex drill bit sets are built for general purpose applications, such as DIY projects, home maintenance and MRO (Maintenance, Repair and Operations). Working materials include steel, copper, aluminum, zinc alloy, cast iron, wood and plastics..
  • 【Package & Size】 - 9 pcs drill bit set in a double blister pack with easy opening design. Size range: 1/16.
Check Stock

3/32-Inch Cobalt Steel M35 Jobber Length Twist Drill Bits for Hard Metal, Stainless Steel, Pack of 12

  • JOBBER LENGTH: 3/32-inch cutting diameter, 1-1/4-inch flute length, 2-1/4-inch overall length, 118 degree point, straight shank.
  • MADE FROM HIGH-SPEED STEEL AND 5% COBALT: improve much higher heat resistance because of cobalt steel's high red hardness, provide strong durable performance compared to typical hss drill bits.
  • CAN BE REPEATEDLY SHARPENED AS NEEDED: cobalt drill bit's hardness is uniform throughout the entire material, so that can be repeatedly sharpened without damaging the cutting edge allowing it to drill more than hss drill bits.
  • APPLICATION: best used for drilling in hard metal, including stainless steel.
  • INCLUDE: 12 pieces of 3/32-inch cobalt drill bits with case.
Check Stock

Drill Hulk 13-Piece M35 Cobalt Drill Bit Set for Hard Metal, Stainless Steel, 1/16-Inch to 1/4-Inch, Jobber Length, 3-Flat Shank

  • JOBBER LENGTH: jobber length cobalt drill bit, 135 degree split point reduces drill walking, 3-flat shank provides a secrue grip in chucks.
  • MADE FROM HIGH-SPEED STEEL AND 5% COBALT: improve much higher heat resistance because of cobalt steel's high red hardness, provide strong durable performance compared to typical hss drill bits.
  • CAN BE REPEATEDLY SHARPENED AS NEEDED: cobalt drill bit's hardness is uniform throughout the entire material, so that can be repeatedly sharpened without damaging the cutting edge allowing it to drill more than hss drill bits.
  • APPLICATION: best used for drilling in hard metal, including stainless steel.
  • INCLUDE: 13 pieces cobalt drill bits in inch sizes 1/16" to 1/4" (1/64" increments) with plastic case.
Check Stock

1/4-Inch Cobalt Steel M35 Jobber Length Twist Drill Bits for Hard Metal, Stainless Steel, Pack of 12

  • JOBBER LENGTH: 1/4-inch cutting diameter, 2-3/4-inch flute length, 4-inch overall length, 135 degree split point, 3-flat shank.
  • MADE FROM HIGH-SPEED STEEL AND 5% COBALT: improve much higher heat resistance because of cobalt steel's high red hardness, provide strong durable performance compared to typical hss drill bits.
  • CAN BE REPEATEDLY SHARPENED AS NEEDED: cobalt drill bit's hardness is uniform throughout the entire material, so that can be repeatedly sharpened without damaging the cutting edge allowing it to drill more than hss drill bits.
  • APPLICATION: best used for drilling in hard metal, including stainless steel.
  • INCLUDE: 12 pieces of 1/4-inch cobalt drill bits with case.
Check Stock

Hi-Spec 99 Piece SAE Multi Drill Bit Set. 14 Sizes from 1/16in to 3/8in. Metal, Wood, Drywall & Plastics Drilling with HSS Titanium Steel Bits. Complete in a Tray Case

  • DRILLING AIN’T EASY: Drilling quickly and accurately into different materials requires choosing the appropriate drill bit type. Get it done right with the Hi-Spec 99 Piece Multi Drill Bit Set. The perfect complement for those everyday drilling jobs in metal, wood, drywall and plastics.
  • 99 PIECE SAE SIZES: The most-used compatible round-shank sizes of HSS metal twist drill bits needed for a range of DIY tasks – 99pc x 14 Sizes of HSS Bits: 1/16, 5/64, 3/32, 7/64, 1/8, 9/64, 5/32, 11/64, 3/16, 7/32, 15/64, 1/4, 5/16, 3/8”.
  • HSS BIT DRILLING: High-Speed tool steel (HSS4241) cuts faster, withstands higher temperatures and retains hardness for longer than ordinary high-carbon steel. Fit to electric power drill drivers and start repairs, installation, and renovation in metal, wood, and plastics.
  • TITANIUM-COATED FOR LIFE: The gold-coloured vapour-deposited Titanium Nitride (TiN) coating improves bit longevity and sharpness. Get increased surface hardness and lubrication properties to improve wear resistance, reduce friction and sticking.
  • KEEP IT TOGETHER: A slim storage tray case keeps bits in separate compartments with a foam insert for further protection. Sizes are printed on the case lid underside and its steel catch snaps shut to makes sure it doesn’....
Check Stock

1/8-Inch Cobalt Steel M35 Jobber Length Twist Drill Bits for Hard Metal, Stainless Steel, Pack of 12

  • JOBBER LENGTH: 1/8-inch cutting diameter, 1-5/8-inch flute length, 2-3/4-inch overall length, 135 degree split point, straight shank.
  • MADE FROM HIGH-SPEED STEEL AND 5% COBALT: improve much higher heat resistance because of cobalt steel's high red hardness, provide strong durable performance compared to typical hss drill bits.
  • CAN BE REPEATEDLY SHARPENED AS NEEDED: cobalt drill bit's hardness is uniform throughout the entire material, so that can be repeatedly sharpened without damaging the cutting edge allowing it to drill more than hss drill bits.
  • APPLICATION: best used for drilling in hard metal, including stainless steel.
  • INCLUDE: 12 pieces of 1/8-inch cobalt drill bits with case.
Check Stock

3/16-Inch Cobalt Steel M35 Jobber Length Twist Drill Bits for Hard Metal, Stainless Steel, Pack of 12

  • JOBBER LENGTH: 3/16-inch cutting diameter, 2-5/16-inch flute length, 3-1/2-inch overall length, 135 degree split point, 3-flat shank.
  • MADE FROM HIGH-SPEED STEEL AND 5% COBALT: improve much higher heat resistance because of cobalt steel's high red hardness, provide strong durable performance compared to typical hss drill bits.
  • CAN BE REPEATEDLY SHARPENED AS NEEDED: cobalt drill bit's hardness is uniform throughout the entire material, so that can be repeatedly sharpened without damaging the cutting edge allowing it to drill more than hss drill bits.
  • APPLICATION: best used for drilling in hard metal, including stainless steel.
  • INCLUDE: 12 pieces of 3/16-inch cobalt drill bits with case.
Check Stock