ReviewsInlet Copper Pipe

Sharkbite 24632LF 45° Hose Bibb 1/2" x 3/4" Multi Turn

  • INSTALLS IN SECONDS: 1/2 inch x 3/4 inch threaded hose bibb valve requires no special tools, no soldering, no crimping or glue. Just push to create a watertight seal.
  • PERFORMANCE: Rated to 200 psi and 200 Degree F. Use in Potable water and Hydronic Heating applications.
  • COPPER, PEX, CPVC, PE-RT: SharkBite hose connector inlet fits Copper, PEX, CPVC and PE-RT Pipe and connects them in any combination.
  • QUALITY: Only SharkBite’s quality and performance is field-proven with more than 550 million connections. SharkBite is the only push-to-connect brand than can ensure a clean, leak-free connection.
  • RESIDENTIAL and COMMERCIAL: All SharkBite fittings meet the same standards for commercial and residential plumbing applications.
Check Stock

Maxitrol RV48L Natural Gas Pressure Regulator 1/2 FPT Thread 13/16 In and Out Opening 1/2 PSIG In 3 -6 WC Out

  • GAS TYPE & PRESSURE - Gas Type: Natural Gas (NG). Inlet gas pressure: 1/2 PSI. Outlet pressure range: 3" - 6" Water Column.
  • PIPE THREAD SIZE - 1/2" Inlet & 1/2" Outlet FPT GAS PIPE. Make sure you measure the gas pipe or regulator opening as close to 13/16 inches as shown in....
  • CAUTION - This regulator has 13/16" openings for 1/2" gas pipes. The 1/2" gas pipe means interior diameter 1/2" but outside diameter is 13/16", refer....
  • MARKING - Model: RV48L, Marking: 1/2 PSIG, Po 3" - 6". Inlet pressure 1/2 PSI. Adjustable outlet pressure 3"-6" Water Column..
  • OPERATE TEMPERATURE - 32°F - 225°F (0°C - 107°C). Do not install the regulator too close to the heating equipment or use in very cold environment.....
Check Stock

Westbrass D105QR-62 Round Lever 1/4-Turn Angle Stop 1/2' Copper x 3/8' Compression, Matte Black

  • Round handle rotates 1/4-turn to stop water flow.
  • 5/8 in. OD (1/2 in. nominal compression) inlet for copper pipe.
  • 3/8 in. OD compression outlet for toilets or sinks.
Check Stock

JOBYNA Electronic Water Descaler System, Alternative Chemical and Salt Free Water Softener Systems Whole House, Prevents Scale Build-up in Pipe, 3 Installation Methods, Works with All Pipes

  • ...here to the surface of pipes and equipment, while allowing the existing limescale decomposes slowly..
  • 【NEW GENERATION DESCALING SYSTEM】New electronic water descalers are equipped with LED light, which display its operating status more clearly. The wider and longer flat copper wire increases the area with the pipe and attaches to the pipes better, makes it easier to wind and works more efficiently..
  • 【THREE WAYS TO INSTALL】No need to damage the pipeline, just wind the coil outside the pipeline. You can install the host vertically, horizontally, or at any other angle by cable ties, adhesive hooks or screws(all the mounting hardware comes included). Reminding: salt free water softener needs to be installed on the water inlet pipe for maximum effect..
  • 【APPLICABLE TO ALL PIPES】The size of 2 copper coils is 39.4''×0.4‘’. The whole house descaler works all pipes, including iron, copper, plastic, stainless steel, even PVC, composite pipe, PE-X, etc. and suitable for pipes of 0.5-2 inches in diameter. Operating voltage is 110-120V..
  • 【100% MONEY BACK GUARANTEE】The scalebl....
Check Stock

SUMMERBUDDY Type B Hose Adapter & Plunger Valve & Pool Hose Holder for Above Ground Swimming Pool, 1.25' to 1.5' Pool Hose Adapter B & On/Off Plunger Valve for Threaded Pumps (2 Packs)

  • 【Multifunctional】This pool hose adapter is used for saltwater system of above ground swimming pool. If your pool inlet/outlet and pipe holder are 1.25" , but you want to install a 1.5" plunger valve, the adapter B will be the perfect solution..
  • 【Waterproof】The rubber ring or band on adapter B and plunger valve tightly with other pool parts to form a sealed space to prevent water leak..
  • 【Convenient】If you want to replace the filter element or upgrade a stronger filter, the plunger valve will help you to control water flow..
  • 【Safe】The pool pipe holder reduce the pressure of the water pipe on the pool wall, thereby reducing damage to the pool..
  • 【Easy installation】The pipe holder is installed between adapter B and inlet or outlet. The big end of pipe holder attach to 1.25" pool inlet or outlet. And the small end of the holder attach to small end of adapter B, then fixed them with clamps. Last, the big end of adapter B attach to the threaded end of plunger valve, simply screw it on.(Contains 2 adapters B, 2 plunger valves, 2 pipe holders).
Check Stock

PERRIN Blow-Off Valve Kit Red Compatible with Subaru WRX 2008-2014

  • This plug is perfectly suitable for F150 2013-2021 and for Expedition Ecoboost Engines 2015‑2021. Perfectly matched, it is a perfect substitute for old or damaged discharge valve plugs..
  • Using this discharge valve plug allows you to discharge hot pressurization to the atmosphere, lower the inlet temperature and improve overall performance throughout the operating range. You can have a clean exhaust valve sound and better performance without recirculating hot air and introducing unwanted heat into the engine..
  • The drain valve plug is easy to install and easy to use. There is no need to install any tools, and the installation can be completed quickly within 15 minutes. First find the blow valve pipe joint, rotate the coupler to remove the blow pipe, then disconnect the BOV hose from the intake pipe, and install the VTA MOD into the pipe before the exhaust valve..
  • This VTA mod allows you to vent the hot boost to the atmosphere instead of recycling it and creating much hotter inlet temperatures. This will lower inlet temperatures and improve overall performance throughout the operating range..
  • The best part is you can have clean blow off valve sound and know you have the best performance without recycling HOT air and introducing unwanted heat into the engi....
Check Stock

8 Pcs Swaging Tool Drill Bit Set HVAC Repairing Set Air Conditioner Manual Copper Pipe Swage Tube Tool with Copper Pipe Cutter and Deburring Tool for Copper Aluminum and Thin Stainless Steel Tube

  • 【What You Will Get】: This air conditioning copper pipe flaring tool set contains 8 tools: 6 Pcs different size drill bits, 1 Pc mini copper pipe cutter, 1 Pc deburring tool, complete set of tools, very suitable for air conditioning copper pipe flaring operation during HVAC installation, no complicated learning, easy to use..
  • 【Drill size】: 6 different sizes of drill bits, including 1/4'', 3/8'', 1/2'', 5/8'', 3/4'', 7/8''.
  • Handle diameter: 7 mm (hexagonal handle), pipe reaming tool is a necessary accessory for repairing air conditioners..
  • 【Mini copper pipe cutter】: 3-28mm (1/8" - 1 1/8") copper pipe cutter can cut copper pipe, steel pipe, stainless steel pipe, aluminum pipe PVC and iron. Note: Cutting PVC pipe is not recommended because it is much more difficult to cut..
  • 【Deburring Tool】: The blade is mounted on the handle can rotate 360 degrees, this tool helps to clean the top of the pipe or tube, it has a compact size and can easily be carried anywhere..
  • 【Why Do You Need HVAC Tools Drill Bit Set】: When connecting copper pipes of air conditioners, the soft copper pipes are expanded by the rotation of the drill bit, so that the two copper pipes are connected without leakage. When used in combination with electric drill and impact....
Check Stock

Shok Blok SB-FPV-40 Water Filter Pressure Regulator Protection Valve for RO & Filter Systems - 1/4\ QC Ports, 40 PSI

  • GAS TYPE & PRESSURE - Gas Type: Natural Gas (NG). Inlet gas pressure: 1/2 PSI. Outlet pressure range: 3" - 6" Water Column.
  • PIPE THREAD SIZE - 3/4" Inlet & 3/4" Outlet FPT GAS PIPE. Make sure you measure the gas pipe or regulator opening as close to 1-1/16 inch as shown in the picture’s table..
  • CAUTION - This regulator has 1-1/16" openings for 3/4" gas pipes. The 3/4" gas pipe means interior diameter 3/4" but outside diameter is 1-1/16.
Check Stock

Grundfos 10SQ10-290 96160143 3\ Submersible Water Well Pump and Motor 10GPM 1HP 200-240V

  • High Head & Flow: 1 HP 220V copper wired capacitor motor with inner control box, provides large flow and high head. It can move water up to 2166GPH or lift water up to 207ft. Designed for 4'' or larger deep well. This submersible well pump is perfect for domestic water boosting, irrigation and Industrial grade heavy duty.
  • Durable & Compact: Qulity stainless steel pump housing and discharge ensures corrosion and abrasion resistance. Durable impellers provide high efficiency and stable performance. Stainless steel inlet strainer screen filters out debris to prevent clogging. Please add a layer of gauze in front of the filtration inlet for a newly drilled well that may contain excessive granular sediment.
  • Easy Installation: Premium mechanical seal prevents water leakage effectively and provides long service life for this irrigation pump. It's compatible with a pressure tank and pressure switch (both not included) and can work as a pressure booster pump. Rustproof 1-1/4" NPT discharge with built-in check valve is easy to install and maintain. Please install extra check valves at outlet pipe to prevent flowback.
  • Safe Operation: Thermally protected motor will prevent the pump from overheating and burning. 10ft copper power cord comes with splice kit for easy ....
Check Stock

Exhaust Tip 3.00' Inlet 4.00' Outlet 16.00' long Dual Slant Angle Stainless Steel WDWD304016-300-SS Wesdon Exhaust Tip

  • Exhaust Tip 3.00″ Inlet 4.00″ Outlet 16.00″ long Dual Slant.
  • Double Wall Slant Could be used as Left or Right Side.
  • Weld On Style fits a 3.00 Exhaust Pipe 3.00 Inlet.
  • (Please measure to make sure it fits your Car or Truck) fits a 3.00 Exhaust Pipe 3.00 Inlet.
Check Stock

Exhaust Tip 2.50' Inlet 4.00' Outlet 16.00' long Dual Slant Angle Stainless Steel WDWD304016-250-SS Wesdon Exhaust Tip

  • Exhaust Tip 2.50″ Inlet 4.00″ Outlet 16.00″ long Dual Slant.
  • Double Wall Slant Could be used as Left or Right Side.
  • Weld On Style fits a 2.50 Exhaust Pipe 2.50 Inlet.
  • (Please measure to make sure it fits your Car or Truck) fits a 2.50 Exhaust Pipe 2.50 Inlet.
Check Stock