ReviewsInput Output Module

WayinTop 2pcs ACS712 Hall Effect Current Sensor Module 30A Range ACS712 Module + 2pcs Voltage Sensor Module DC0-25V Voltage Tester Terminal Sensor for Arduino

【Perfect Combination】Using this product can measure both voltage and current, very suitable for DIY electronic design projects..
【Current Sensor Module】Chip: ACS712ELC-30A.
Pin 5V power supply, on-board power indicator.
The module can measure positive and negative current of 30 amperes, corresponding to analog output of 66mV/A..
【Voltage Sensor Module】Voltage input range: DC0-25V.
DC input connector: Terminal cathode connected to VCC, GND negative pole.
Output interface: "+" then 5/3.3V, "-" then GND, "s" then the for Arduino AD pins..
【Package Included】2 x ACS712 Hall Effect Current Sensor Module + 2 x Voltage Sensor Module DC0-25V Voltage Tester Terminal Sensor.

Check Stock

Power Supply, DPS3005 /DPS5005 Communication Version Bucks Power Supply Step-Down Voltage Converter(DPS3005-USB-BT)

...005 have same functions, only the technical parameters are different,for example, voltage, current ,etc.
This module has power-down stored function and can store 10 groups preset value.And it also has the function of extracting quickly two groups stored value. Though this module has reverse connection protection and output short circuit protection, you can muse be in strict accordance with connection description to connect. If you connect the supply power with output, the module will be burnt.
Compared with the traditional analog power supply, it is more convenient to quickly extract the voltage or current required. This module has many advantages, small size, advanced function, good visual effect, high operability, high-precision, being used independently, being inset into the device and been widely applied.
LCD display on the module has the function digital voltmeter and ammeter.You can view the preset voltage, input voltage, output voltage, the preset current, output current, output power, etc.
On the setting data interface, you can adjust over-voltage value, over-current value, over-power value, data set and LCD brightness. On the output state remind area, you can see that output opens or not, the state of constant voltage and constant current, outpu....

Check Stock

Diymore 2pcs 20A 300W CC CV Step Down Module Adjustable DC 6-40V to 1.2-36V Voltage Regulator Buck Converter Constant Current Power Supply Module 20v to 12v Step Down

This step-down voltage module with a wide input voltage range from 6V to 40V, the step-down converter can accurately adjust output voltage and current..
It is designed with 75V/80A large current dual MOS tube. Input and output use high frequency low resistance electrolytic capacitor, low ripple, stable output..
The efficiency can be up to 96%, measured at 20A, converting 24V to 12V. Wiring is convenient with these large current 30A screw terminals..
The buck module has 2 heat sink that could enhance heat dissipation, extending service life..
When there is a big difference between input and output voltage, please decrease power and current..

Check Stock

DROK DC Buck Converter, 5.3V-32V to 1.2V-32V 12A Adjustable Power Supply, 5v 9v 12v 24V 30V 32V Step Down Voltage Regulator with LCD Display Volt Transformer Reducer CC CV for RV Solar Panel Golf Cart

【Parameter】 DROK Power Supply Module input volt range is DC 5.3-32V.
Output volt range is DC 1.2-32V which is variable. Output current can reach to 8A and Output Power can reach to 120W for long-time use. If enhance heat dissipation, this converter can reach 12A and 160W output..
【Characteristics】 This Buck Converter is equipped with LCD Display, Acrylic Case and Heat Sink. LCD Screen can display input/output voltage, output current and output power. Voltage precision is 0.05V, current precision is 0.005A. Acrylic case can keep the converter board away from dust, which is protective. Heat Sink can keep module 120W for long-time using in a low temperature. If you want to reach maximum power 160W, please improve heat dissipation..
【Easy Operation】 A user manual will be included in package, which can help you easier to operate. The button can control ouput voltage ON/OFF status, and you can set the default output state is ON/OFF for the next time. The potentiometer can help you to adjust volt amp in a simple and fast way..
【Protection】 It has reverse-connect protection, short circuit protection and over current protection. When you connect the input wire reversely or short circuit, the module will not burn. And roate the CC potentiometer to....

Check Stock

DZS Elec 6pcs XL6009 DC-DC Booster Converter Module 3V-32V to 5V-35V 4A Adjustable Step-up Voltage Regulator 5V 9V 12V 24V Power Supply Module

XL6009 DC-DC Adjustable Booster Power Converter Module, High efficiency non-isolated booster module can be used for booster voltage stabilizer power supply, DIY adjustable mobile power supply, booster charger, etc..
Input Voltage: 3V-32V, The optimal operating voltage range is 5-32V.
Output Voltage: 5V-35V Continuing Adjust (Step-up module, output voltage is higher than input voltage).
Input Current: 4A (max) Non-Load 18mA (The higher voltage, the greater no-load current.).
The booster power board is equipped with 4A high-efficiency MOSFET switch tube, with the conversion efficiency up to 94%..
Ultra high switching frequency 400KHz, the filter capacitance with small capacity can achieve very good effect, smaller ripple and the volume..

Check Stock

High Frequency Transducer, Bandwidth Mixing Board Mixer Module -10dBm for Quadrature Modulation for Base Station for HF VHF Receiver

【Important Data】: SSB noise figure (NF) of 9.75 dB--Input IP3: 28.5 dBm--Input P1dB: 13.3 dBm--Typical LO drive: 0 dBm--Power conversion gain of 1.8 dB.
【Wild Used】: This 5V double balance up and down frequency mixer module is widely used for cellular base station receivers, Radio link down converters, Broadband block conversion, Instrumentation.
【Low Power】: Our 130mA 50 Ohms Balun coil coupling frequency conversion mixer features adjustable bias for low power operation, so you can trust and use this RF mixer inverter with confidence.
【Wonderful Components】: This 5V ADL5801 double balance up and down frequency mixer module is equipped with exposed paddle, 4mm x 4mm, 24-lead LFCSP package, so it will be an ideal choice for you.
【Size】: Power supply: DC+5V@80mA(anti-reverse connection protection.)--RF_IN/RF_LO input frequency range: 10-6000Mhz--Input and output impedance: 50 ohm--Type:Input Balun coupling, Input/output Balun coupling(Optional)--Weight: Approx.15g/0.5oz.

Check Stock

Synthrotek, Erica Synths Swamp DIY Kit

The SWAMP is a random CV and audio generator inspired by the famous Wiard Wogglebug module..
External audio input routed to ring modulator..
Clock input and output to sync the module to your modular system.

Check Stock

Supco Q103 Sequencer

Choose between Eurorack power, FRACK power (panel is still Eurorack format), or 9V battery/wall plug.
Coarse & fine clock adjustment - Switchable linear 'random' function with speed adjustment - Momentary & Hard Hold Function - Manual Step Button - Internal/External Clock Switch - Reset Input Jack - Current draw is 20mA - Size: 3U 20HP - Module depth (Eurorack version): 1.5 inches.
3 CV Outs, each with their own attenuator, 0-5 volt output..

Check Stock

UMLIFE 4PCS AC/DC to DC Step Down Buck Converter AC 5-30V DC 5-48V 24V 36V 48V to DC 2.5-35V 12V Voltage Regulator Board 2A Adjustable Volt Power Supply Module

4PCS LM2596HV AC/DC to DC Buck Step Down Converter Module 3v 3.3V 5V 6V 9V 12V 15V 24V DC 5V-50V Adjustable Step-Down 3A Power Supply.
Adjustable AC/DC to DC buck converter power supply module Voltage Regulator.
Input ac voltage AC5V~AC30V or dc5v-50v. Due to the large fluctuation of ac voltage, the recommended ac voltage range has been reserved..
The power module adopts plug-in LM2596HV, LM2596 version of high voltage, the highest input voltage is 50V(limited by filter capacitor voltage) with external radiator, can withstand high current work..
Input voltage range: AC 5V-30V, DC 5V-50V Output output range: DC 3.3V-33V.

Check Stock

Level Translator 5V/24V, 8 Channel NPN/PNP to NPN Level Conversion Module, Level Conversion Board, Voltage Level Converter Board 10MHZ

【Convert Input Level Signal】The module can convert input 5V level signal to 24V level signal, or convert input 24V level signal to 5V level signal..
【 Anti-interference】It can also convert signal 5V to 5V, or 24V to 24V level, and isolate input signal and output signal through optocoupler, which can improves anti-interference ability of circuit..
【Set by Dip Switch】Input level can be set by DIP switch, 24V level output is NPN OC output, output current is 100mA..
【Strong Driving Ability】It has conversion and amplification circuit, good wave, strong driving ability..
【PLC Interface Standards】Compatible with a common-cathode or common-anode input connection, matching European and Japanese PLC interface st Plc Interface Standardsandards..

Check Stock

Juried Engineering Microchip MCP602-I/P MCP602 Dual Operational Amplifier Op-Amp 2.8MHZ 2.3V/us DIP-8 Breadboard-Friendly (Pack of 1)

DROK micro voltage converter with low voltage input range DC 4.8-35V, positive and negative dual output voltage is ±15V, rated output current is 660mA..
APPLICATION: the step-up regulator module is suitable for sensor, operational amplifier, audio and other devices that needs positive-negative power output..
SMALL MODULE HIGH EFFICIENCY: DROK boost converter is with small dimension 64x27.5x12.5mm.
the small module conversion rate can be up to 88%..
TWO MOUNT METHODS: the volt transformer module not only support row pin welding, but also lead mounting, which will be convenient for your use..
NOTE: please note that although the module is with short circuit protective function, it can not in long continuous short circuit, or it will be damaged..

Check Stock