ReviewsInsert Bearing Housing

SKF F4B 204-TF Ball Bearing Flange Unit, 4 Bolts, Set Screw Locking, Regreasable, Seals with Flingers, Cast Iron, 2-1/4\ Bore, 5-5/8\ Bolt Hole Spacing, 11840lbf Dynamic Capacity

Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals and flingers on both sides of the bearing keep lubricant in and contaminants out.
Grease fitting on the housing for reapplying lubricant.

Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals and flingers on both sides of the bearing keep lubricant in and contaminants out.
Grease fitting on the housing for reapplying lubricant.

Made of bearing steel and cast iron shell, high hardness and durable..
Pillow block bearing is a kind of bearing unit which combines rolling bearing and bearing block, which has good versatility and interchangeability..
Two-bolt housing with ball bearing insert for ready-to-mount installation..

Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals and flingers on both sides of the bearing keep lubricant in and contaminants out.
Grease fitting on the housing for reapplying lubricant.

EASY TO USE: The slide hammer bearing puller can be used in four steps: Insert the pilot bearing puller, turn the attachment housing expanding both jaws against the pilot bearing, attach a slide hammer, and use the slide hammer to remove the bearing.
SAVE MONEY: Getting a pilot bearing replaced in an auto shop could cost you up to $650.
You can save hundreds of dollars by using this one pilot puller.
VARIETY OF USES: Not only can this pilot bearing tool be used as a bearing puller, but it can also be used as a bushing tool on starters and generators.
This pilot bearing removal tool will also fit any 5/8” x 18” or 3/4” x 16” threaded rods.
DURABLE: Made from steel, this bearing and bushing removal tool can withstand years of regular pilot bearing jobs.
This blind hole bearing puller is built to last.
DIMENSIONS: This pilot bearing remover is easy to store anywhere at just 10.4" x 3.4" x 1.3". The blind bearing puller is also easy to wield, weighing in at just 13.6 ounces, making it a great pilot tool.

Straight pipe thread tapped housing with self-aligning ball bearing insert for shaft misalignment adjustment.
Set screw locking collar for secure attachment to shaft.
Cast iron housing for strength and durability.

Application -- Compatible with Mercruiser Alpha Alpha 1 MR Bravo OMC Cobra Volvo. With this tools set, you could replace gimbal bearings and hinge pins..
Gimbal Bearing Puller -- This bearing puller remover can easily remove the gimbal bearings on bell housings by turning the end of the tool with a wrench..
Gimbal Bearing Installer -- Used to install the new gimbal bearing back, set the bearing on the installer than insert the installer in engine. Also it can be used to check engine coupler alignment with the gimbal bearing and drive..
Hinge Pin Tool -- This tool is used to remove and install hinge pins for Mercruiser drive units. It can separate the housing from the gimbal ring on the hinge pin bolt..
High Quality -- Our tool set is made of premium solid steel with nice black Oxide finish which is anti-corrosion and rustproof. The tools are specially hardened for added strength and impact protect. So the product can be durable and service a much longer time..

Cast iron flanged housing with a solid base for vibration damping and structural rigidity.
Standard-duty, deep-groove ball bearing insert for applications with moderate radial loads and light to moderate thrust or combination loads.
Felt labyrinth seals on both sides of the bearing keep lubricant in and contaminants out and flingers provide extra sealing protection.
Setscrew lock for a three-point contact hold on the shaft.
Grease fitting on the housing for reapplying lubricant.

Cast iron flanged housing with a pilot extension for accurate location and increased stability.
Medium-duty, deep-groove ball bearing insert for applications with moderate to high radial loads and moderate thrust or combination loads.
Felt labyrinth seals on both sides of the bearing keep lubricant in and contaminants out and flingers provide extra sealing protection.
Setscrew lock for a three-point contact hold on the shaft.
Grease fitting on the housing for reapplying lubricant.

Cylindrical cartridge housing with ball bearing insert for supporting shafts with radial or combined radial and thrust loads.
Skwezloc locking collar for secure attachment to shaft.
Cast iron housing for strength and durability.

Cast iron flanged housing with a solid base for vibration damping and structural rigidity.
Standard-duty, deep-groove ball bearing insert for applications with moderate radial loads and light to moderate thrust or combination loads.
Felt labyrinth seals on both sides of the bearing keep lubricant in and contaminants out and flingers provide extra sealing protection.
Setscrew lock for a three-point contact hold on the shaft.
Grease fitting on the housing for reapplying lubricant.