ReviewsKeyless Bushing Pulley

TB Woods 2517 TL2517238 Taper Lock Bushing, Cast Iron, Inch, 2.375\ Bore, 1200 lbs/in Torque, Standard Design, Shallow Keyway

  • Taper lock bushing with a torque capacity of 1,200 in-lbs for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Cast iron for resistance to wear, galling, and corrosion.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper lock bushings from various manufacturers.
Check Stock

TB Woods 2012 TL201230MM Taper Lock Bushing, Cast Iron, 30 mm Bore, 1200 lbs/in Torque, Standard Design, Standard Keyway

  • Taper lock bushing with a torque capacity of 1,200 in-lbs for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Cast iron for resistance to wear, galling, and corrosion.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper lock bushings from various manufacturers.
Check Stock

TB Woods 1610 TL161025MM Taper Lock Bushing, Cast Iron, 25 mm Bore, 1200 lbs/in Torque, Standard Design, Standard Keyway

  • Taper lock bushing with a torque capacity of 1,200 in-lbs for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Cast iron for resistance to wear, galling, and corrosion.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper lock bushings from various manufacturers.
Check Stock

TB Woods 1108 TL110858 Taper Lock Bushing, Cast Iron, Inch, 0.625\ Bore, 1200 lbs/in Torque, Standard Design, Standard Keyway

  • Taper lock bushing with a torque capacity of 1,200 in-lbs for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Cast iron for resistance to wear, galling, and corrosion.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper lock bushings from various manufacturers.
Check Stock

GM CLIMBING UIAA Certified 30kN Swing Cheek Micro Pulley CE General Purpose (Black, Pack of 2)

  • Light and compact micro pulley. You could use it in 100 applications, in hauling, dragging, tensioning system, in rescue, tree climbing, and etc..
  • Swing cheek makes the rope installation and removal much easier, which much facilitate the system setting process..
  • Smooth rotation provides maximum mechanical advantage..
  • Of 30kN Breaking strength, the pulley will satisfy almost all your requirements..
  • Black-Bushing: larger contact area with axle, much less wear for longer service life, suitable for slow rigging with heavy weight. Light and compact, the micro pulley will take up almost no space in your rack..
Check Stock

GM CLIMBING Hitch Slack Tending Pulley Kit for Doubled Rope Climbing System Basic Unit of General Hauling - 30kN Swing Cheek Micro Pulley (Black, Bushing) & Oval Locking Carabiner & 30in 8mm VT Prusik

  • Slack Tending Pulley Kit from GM CLIMBING, which contains: 1x 30in 8mm Friction Hitch VT Prusik, 1x 27kN Oval Twist Locking Carabiner, 1x 30kN Swing Cheek Micro Pulley..
  • Mainly used as core part of doubled-rope technique climbing system (ddrt), also widely use as flipline adjuster. For general pulley system, such kit can also made itself a pulley system with process capture..
  • Ball bearing or bushing 30kN Swing Cheek Micro Pulley are chosen for kit. It's easier to install or remove rope from pulley due to swing plates, much facilitating whole set-up process..
  • VT Prsuik with Heat Resistance! 50% Kevlar Fiber is mingled during sheath braiding, adding durability (cord rating to 25kN) and excellent heat resistance for your friction hitch..
  • It's always a good idea to have an oval locking carabiner to use with pulleys, for better balance, also for safer operation..
Check Stock

Martin SH 1 Quick Disconnect Bushing, Sintered Steel, Inch, 1\ Bore, 1.871\ OD, 1.31\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin JA 1 Quick Disconnect Bushing, Sintered Steel, Inch, 1\ Bore, 1.375\ OD, 1.06\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin SDS 2 Quick Disconnect Bushing, Ductile Iron, Inch, 2\ Bore, 2.187\ OD, 1.37\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Ductile iron for greater strength than gray cast iron and resistance to wear, galling, and corrosion.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin JA 7/16 Quick Disconnect Bushing, Sintered Steel, Inch, 0.43\ Bore, 1.375\ OD, 1.06\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock

Martin SK 7/8 Quick Disconnect Bushing, Sintered Steel, Inch, 0.87\ Bore, 2.812\ OD, 1.93\ Length

  • Quick disconnect bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Split through flange and taper to provide strong clamping on the shaft.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Set screw over keyway to help keep key in place on vertical shafts and with vibrating loads.
Check Stock