ReviewsLarge Aluminium Alloy Die

uxcell 5/8-24 UNEF Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel

  • ...rust, the thread is clear and easy to repair..
  • Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

uxcell 5/8-18 UNF Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel

  • ...rust, the thread is clear and easy to repair..
  • Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

uxcell 3/8-16 UNC Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel

  • ...rust, the thread is clear and easy to repair..
  • Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

uxcell M6 X 1.0 Metric Round Die, Machine Thread Left Hand Threading Die, Alloy Steel

  • ...rust, the thread is clear and easy to repair..
  • Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

uxcell 1/2-20 UNF Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel

  • ...rust, the thread is clear and easy to repair..
  • Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

uxcell M16 X 1.5 Metric Round Die, Machine Thread Right Hand Threading Die, Alloy Steel

  • ...rust, the thread is clear and easy to repair..
  • Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

uxcell 1/2-13 UNC Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel

  • ...rust, the thread is clear and easy to repair..
  • Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

uxcell M2.5 x 0.45 Metric Round Die, Machine Thread Left Hand Threading Die, Alloy Steel

  • ...rust, the thread is clear and easy to repair..
  • Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

Venzo Fitness Exercise Indoor Bike Compatible with Shimano SPD Pedals with Toe Clips & Cleats

  • GREAT FOR SPIN BIKES: The pedals are specially designed for spin bikes. Strong material: Die-cast aluminium body, Extra heavy-duty oversized CNC Cr-Mo 9/16" Axle.
  • Smooth-riding: sealed bearings. Friendly reminder: Please do NOT use other pedals such as road or MTB pedals on spin bikes..
  • DUAL FUNCTION: Riding with clipless shoes: More efficient energy transfer to pedals or ride with casual shoes. LARGE PLATFORM: The aluminium body is 105 x 78mm relatively large. It ensures more riding stability..
  • FULLY COMPATIBLE: Compatible with all Shimano SPD MTB pedals systems. This means you can use Shimano SPD cleats on these pedals or use these cleats on Shimano SPD pedals..
  • ADJUSTABLE TENSION: The cleat's tension could be adjusted by the screw on the side of the pedal. It allows riders to achieve perfect clip in and out feelings. Package: One set of pedals with toe clips and cleats. Total Weight: 744g=1.6lbs /pair..
  • ORDER NOW, WORRY-FREE! We're so confident about our product quality that we can provide a 2-year warranty! Made in Taiwan..
Check Stock

uxcell 1/4-28 UNF Round Die, Machine Thread Right Hand Threading Die, Alloy Tool Steel, 2pcs

  • ...rust, the thread is clear and easy to repair..
  • Easy to Use: The positioning groove of the die should be aligned with the fastening screw in the middle of the die wrench, and the screw should be inserted into the slot of the die and tightened. The end of the bar should be chamfered 1*45 degree, and the chamfer is too large to cut in..
  • Tips: It needs to be reversed every 1/4~1/2 turn to facilitate the chip discharge from the chip hole. Suitable lubricating oil should be added to the cutting edge of the die when tapping the thread. The bar diameter should be smaller ( about 0.05mm-0.15mm) than the nominal diameter of the required thread. Excessive diameter can easily cause difficult cutting and lead to damage to the die teeth..
Check Stock

Slide-Co 171786 Awning Operator Crank Handle, 3/8 inch Bore, Aluminum

  • Popular for visible architectural applications such as window frames, door frames, roofs, and sign frames.
  • Most common alloy used for aluminium extrusion.
  • 50cm( 19.7 inch) length 6063 Aluminium Alloy( Al--Si) Round Tube, outer diameter( OD) varies from 8mm to 20 mm.
  • Allows complex shapes to be formed with very smooth surfaces fit for anodizing.
  • Has good mechanical properties, is treatable and weldable, similar to the British aluminium alloy HE9.
Check Stock