ReviewsLarge Thrust Bearing

PULSAR 03-07 6.0 Turbo Rebuild Kit 6.6 Duramax LLY LBZ Staggered Step Gap Seals

  • 360º thrust bearing vs. stock 270º thrust bearing enhances turbochargers durability..
  • Staggered step gap compressor and turbine ends seal rings reduce oil blow by of the seals.
  • Fits 2003-2007 Ford 6.0L Diesel F250 F350 F450 F550 GT3782VA turbo.
  • Fits 2004.5-2007 GMC/Chevy 6.6L Duramax LLY LBZ Silverado Sierra HD GT3788VA.
Check Stock

DNJ TW950 Thrust Washer For 88-04 Toyota, Lexus, Tacoma, Tundra, 4Runner, T100, Pickup, ES300, Camry, ES250, 2.5L-3.4L V6, DOHC, SOHC, Naturally Aspirated

  • Thrust washers limit axial movement and provide a bearing surface. Thrust bearings are designed to support axial load..
  • Thrust washers either have multiple tapered ramps and relatively small flat pads or have curved surfaces that follow a sine wave contour around their circumference..
  • Tear-drop or through grooves on the flange faces and wedge shaped ramps at each parting line allow engine oil to enter between the shaft and bearing surfaces..
  • Manufactured to meet or exceed OE specifications.
Check Stock

Enduro ABEC-5 Angular Contact Bearing, 71903 17X30X7-71903 LLB

  • Single-row angular contact ball bearing, supporting moderate to heavy one-directional thrust loads, and combined loads where thrust load is predominant.
  • Ball contact angle of 40 degrees relative to the inner and outer raceways increases thrust load capacity.
  • Open configuration for lubrication applied in place.
  • Brass cage evenly spaces balls for reduced friction, vibration, and noise.
  • ABEC 1 tolerance ratings for accuracy and low rotational speeds.
Check Stock

SKF F4B 100-RM Ball Bearing Flange Unit, 4 Bolts, Set Screw Locking, Regreasable, Contact Seal, Cast Iron, 1\ Bore, 2-3/4\ Bolt Hole Spacing, 3150lbf Dynamic Load Capacity

  • Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
  • Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
  • Set screw locking for secure attachment to shaft.
  • Contact seals on both sides of the bearing keep lubricant in and contaminants out.
  • Grease fitting on the housing for reapplying lubricant.
Check Stock

SKF F4B 200-RM Ball Bearing Flange Unit, 4 Bolts, Set Screw Locking, Regreasable, Contact Seal, Cast Iron, 2\ Bore, 5-1/8\ Bolt Hole Spacing, 9800lbf Dynamic Load Capacity

  • Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
  • Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
  • Set screw locking for secure attachment to shaft.
  • Contact seals on both sides of the bearing keep lubricant in and contaminants out.
  • Grease fitting on the housing for reapplying lubricant.
Check Stock

SKF F4B 108-RM Ball Bearing Flange Unit, 4 Bolts, Set Screw Locking, Regreasable, Contact Seal, Cast Iron, 1-1/2\ Bore, 4\ Bolt Hole Spacing, 6900lbf Dynamic Load Capacity

  • Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
  • Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
  • Set screw locking for secure attachment to shaft.
  • Contact seals on both sides of the bearing keep lubricant in and contaminants out.
  • Grease fitting on the housing for reapplying lubricant.
Check Stock

SKF F4B 104-RM Ball Bearing Flange Unit, 4 Bolts, Set Screw Locking, Regreasable, Contact Seal, Cast Iron, 1-1/4\ Bore, 3-5/8\ Bolt Hole Spacing, 5730lbf Dynamic Load Capacity

  • Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
  • Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
  • Set screw locking for secure attachment to shaft.
  • Contact seals on both sides of the bearing keep lubricant in and contaminants out.
  • Grease fitting on the housing for reapplying lubricant.
Check Stock

SKF F4B 103-RM Ball Bearing Flange Unit, 4 Bolts, Set Screw Locking, Regreasable, Contact Seal, Cast Iron, 1-3/16\ Bore, 3-1/4\ Bolt Hole Spacing, 4380lbf Dynamic Load Capacity

  • Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
  • Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
  • Set screw locking for secure attachment to shaft.
  • Contact seals on both sides of the bearing keep lubricant in and contaminants out.
  • Grease fitting on the housing for reapplying lubricant.
Check Stock

SKF F4B 204-TF Ball Bearing Flange Unit, 4 Bolts, Set Screw Locking, Regreasable, Seals with Flingers, Cast Iron, 2-1/4\ Bore, 5-5/8\ Bolt Hole Spacing, 11840lbf Dynamic Capacity

  • Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
  • Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
  • Set screw locking for secure attachment to shaft.
  • Contact seals and flingers on both sides of the bearing keep lubricant in and contaminants out.
  • Grease fitting on the housing for reapplying lubricant.
Check Stock

SKF F4BM 300-TF Ball Bearing Flange Unit, 4 Bolts, Medium Duty, Set Screw Locking, Seals with Flingers, Cast Iron, 3\ Bore, 6\ Bolt Hole Spacing, 16360lbf Dynamic Capacity

  • Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
  • Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
  • Set screw locking for secure attachment to shaft.
  • Contact seals and flingers on both sides of the bearing keep lubricant in and contaminants out.
  • Grease fitting on the housing for reapplying lubricant.
Check Stock

M30 IPE KV100 Pro V2.0 MAD COMPONENTS Drone brushless Motor for Heavy Multirotor Quadcopter Hexrcopter RC DIY

  • More efficient and drawing more power than equivalent motors in the market.
  • Precise manufacturing workmanship, perfect winding, absolutely compete with top brands.
  • This large drone brushless motor was designed for rigorous conditions and endurance flight, IP44.
  • 1 x Double row angular contact ball bearing 1 x Tapered Roller Bearing,Over-sized durable bearings for increased life, durability Support 12-16S.
  • Pay attention the extened wire =70mm. high end heavy lift industrial drone use, max thrust 49kg @60V with 40in prop..
Check Stock