ReviewsLocating Pin

Razor E100/E125/E150/E175 Battery Set

NOTE: E100/E125 Scooter versions can be determined by locating your bar code ID on the bottom of the scooter. The 7th and 8th digit in the series will tell you the version of your product: 01=version 1.
09=version 9, and so on. Please be sure you identify your product version before placing an order for a battery.
This battery set is used on the Razor E100/E125 (Versions 16 and up), the Razor E150 (Versions 6 and up), the Razor E175 (Versions 19 and up) and the Razor eSpark..
Length: 3.54 inches (90mm), Width: 2.72 inches (69mm), Height: 3.94 inches (100mm).
Plug Style: 3 hole (2-pin), female w/ reset wires.

Check Stock

[2 Pack] 12 inch x 7/8 inch x .095 inch Urethane Band Saw Tires - No Adhesive Needed - Compatible with Branded Bandsaws Including Jet Grizzly, Powermatic

use on 14" Band Saws and 24" Scroll Saws.Table Inserts (pack of 2). Material: Aluminum.
They fit Delta, Rockwell, some Jet, Ridgid, Grizzly, and other imports..
Make sure your insert recess has the locating pin on the side , not on the rear.
IMPORTANT INSTALLATION NOTE:I have sold several hundred of these and occasionally someone will have the problem of it being a bit too large. First make sure the lip of the hole is free from dirt. If a table alignment pin,is not tight or missing,often the blade mounting slot will close up some over time which reduces the insert hole diameter slightly. I tap a flat head screw driver into the blade installation slot a bit to wedge it open. That should spread the insert hole enough for it to fit.
Please measure your saw as some Delta & Rockwell 14" bandsaws has slightly smaller holes for the throat plate. If so some slight filing or sanding may be required..

Check Stock

Thomegoods Urethane Band Saw Tires FIts 12 inch x 7/8 inch x .095 inch No Adhesive Needed Fits for Jet Grizzly, & Powermatic

Please measure your saw as some Delta & Rockwell &Grizzly14" bandsaws has slightly smaller holes for the throat plate. If so some slight filing or sanding may be required.If you mind, please don't buy it..
Make sure your insert recess has the locating pin on the side, not on the rear..
use on 14" Band Saws and 24" Scroll Saws.2&1/2" X .100 thick Please measure your saws recess to ensure proper fit.
They fit Delta, Rockwell, some Jet, Ridgid, Grizzly, and other imports..
IMPORTANT INSTALLATION NOTE:I have sold several hundred of these and occasionally someone will have the problem of it being a bit too large. First make sure the lip of the hole is free from dirt. If a table alignment pin,is not tight or missing,often the blade mounting slot will close up some over time which reduces the insert hole diameter slightly. I tap a flat head screw driver into the blade installation slot a bit to wedge it open. That should spread the insert hole enough for it to fit.

Check Stock

RED WOLF Replacement for Subaru Forester/Outback/Crosstrek 2009-2020 to Add Subaru Trailer 4-Pin Trailer Wiring Harness Connector 4 Way Flat Trailer Extension Plug

For Subaru Forester 2009-2020, 2010-2020 Subaru Outback/Wagon/Except Sport, 2013-2015 Subaru XV Crosstrek/Except Hybrid, 2016-2019 Subaru Crosstrek/Except Hybrid models..
The subaru 4 pin trailer harness allow to add a trailer/ hitch or solve the issue with lighting on trailer. Totally 6.6 ft wire harness to meed the need when you hook them up..
No cutting or splicing factory wire. What's more, the fuse was set out side the harness so that if we needed to change the fuse we could do it without having to remove the trim..
Easy install: The subaru trailer 4 way harness is directly plug the white connector into the existing factory harness . Attaching the ground screw and locating the adapter box wherever you feel it would be out of the way..
Anti- dust & rain. 4 way flat subaru trailer connector comes with dust cap that protect the 4pin metal from dust or water to prevent go rust. High quality material make, durable use, as you can see at advertising pictures..

Check Stock

Jackson Safety Pipe Marker Centering Head Tool, Curv-O-Mark Jumbo 7, To measure Pipes 1" and Up, Standard 8" Y-Type Head, Adjustable Dial Set Level, 14776

PIPE MEASURER – Designed for pipe fitters and welders as an measurer for setting center lines, establishing angles and marks for butt-ins, locating points inside pipes and tanks, laying out keyways, and measuring declivity.
JUMBO SIZE – Curv-O-Mark Jumbo #7 model digital angle finder tool used on pipes and tanks that measure 1" in diameter and larger.
Y HEAD – The center finder has a 8" Y type head fitted with adjustable dial bubble protractor (DSL).
BEST OPERATION – Use this Jackson Safety hardened centering pin angle finder with a small hammer or mallet to tap the pin in for the most effective pipe marking.
SAFETY STANDARDS – When it comes to providing innovative safety solutions, unparalleled features, long-lasting value, and comfort on the job, Jackson Safety has set the standard for the best protective gear and tools in the industry.

Check Stock

Handheld Colorimeter Color Difference Meter with Built-in White Plate 4mm Measuring Aperture

◆ Illuminating/Viewing Geometry: 8°/d.
◆ Double locating: Illuminating locating and precise cross locating..
Built-in white plate parameters, no need to do calibration..
◆ 4mm measuring aperture Widely used in food, chemical industry, electronics, automobile, food and other fields..

Check Stock

2 Rear Notch Bandsaw Table Insert fits Delta 14 Part 426-02-063-0001 426-02-063-0002

Table Inserts (pack of 2), new bandsaw aluminum table inserts for Delta 14" (LBS-56) and most import bandsaws..
Make sure your insert recess has the locating pin on the rear, not on the side.
2&1/2" X .100 thick. Please measure your saw as some Delta & Rockwell 14" bandsaws has slightly smaller holes for the throat plate. If so some slight filing or sanding may be required..
Fits the following Delta 14"saws: 28-141, 28-200, 28-203, 28-205, 28-207, 28-209,28-216, 28-230, 28-231, 28-240, 28-241, 28-243, 28-245, 28-248, 28-254, 255, 28-262, 28-263, 28-269, 28-270, 28-275, 28-278, 28-280, 28-283, 28-285, 28-290, 28-293, 28-299, 28-300, 328-03, 28-306, 28-345, 28-348, 28-350, 28- 365, 28-366, 28-380, 28-475, 28-651, 28-652, 28-653,28-654,28- 656, 28-662 and others.Interchanges with Delta part number 426020630001.

Check Stock

Colorimeter Color Analyzer Meter SC-10 Color Difference Reader D65 4mm Lab Delta E Portable

Hand-held structure, small and convenient, make the measurement easier.
New integrating sphere design for more stable measurement.
Built-in white plate parameters, no need to calibrate each time which realize rapid measurement.
Double locating: illuminating locating and cross locating.
Equipped with rechargeable high-capacity li-ion battery..

Check Stock

SC-10 Simplified Portable Colorimeter Color Analyzer Meter Color Difference Reader D65 4mm Lab Delta E

Hand-held structure, small and convenient, make the measurement easier.
Built-in white plate parameters, no need to calibrate each time which realize rapid measurement.
Equipped with rechargeable high-capacity li-ion battery.
New integrating sphere design for more stable measurement.
Double locating: illuminating locating and cross locating..

Check Stock

Table Inserts (Pack of 3) for 14' Band saws or Scroll saws,Diameter: 2.5 in, Thickness: 0.1 in.(Please make sure this is your size)

Three inserts to protect your expensive blades Please measure your saw as some Delta & Rockwell &Grizzly14" bandsaws has slightly smaller holes for the throat plate. If so some slight filing or sanding may be required.If you mind, please don't buy it..
use on 14" Band Saws and 24" Scroll Saws..
2&1/2" X .100 thick Please measure your saws recess to ensure proper fit They fit Delta, Rockwell, some Jet, Ridgid, Grizzly, and other imports..
Make sure your insert recess has the locating pin on the side, not on the rear.
IMPORTANT INSTALLATION NOTE:I have sold several hundred of these and occasionally someone will have the problem of it being a bit too large. First make sure the lip of the hole is free from dirt. If a table alignment pin,is not tight or missing,often the blade mounting slot will close up some over time which reduces the insert hole diameter slightly. I tap a flat head screw driver into the blade installation slot a bit to wedge it open. That should spread the insert hole enough for it to fit.

Check Stock

Jackson Safety Pipe Marker Centering Tool, Curv-O-Mark Standard 6, 14775 - Use to measure Pipes 0.5\ and Up, Standard 4\ Y-Type Head, Adjustable Dial Set Level

PIPE MEASURER – This easy-to-use marking tool is designed for pipe fitters and welders as an economical measuring tool for setting center lines, establishing angles and marks for butt-ins, locating points inside pipes and tanks, laying out keyways, and measuring declivity.
STANDARD SIZE – This Curv-O Standard #6 model level tool may be used on pipes and tanks that measure one-half of inch in diameter or larger.
Y-HEAD – The center finder has a 4 inch Y-type head fitted with an adjustable dial bubble protractor (DSL).
BEST OPERATION – Use this manual Jackson Safety hardened centering pin angle finder with a small hammer or mallet to tap the pin in for the most effective pipe marking.
SAFETY STANDARDS – When it comes to providing innovative safety solutions, welding tools with unparalleled features, long-lasting value, and comfort on the job, Jackson Safety has set the standard for the best protective gear and tools in the industry.

Check Stock