ReviewsLow voltage Motor Driver

Milwaukee 2897-22 M18 Fuel 2-Tool Combo Kit Red

Hammer drill/driver's POWERSTATE Brushless Motor delivers 1200 in. lbs. of peak torque and up to 2000 RPM for faster drilling speeds..
Impact driver's POWERSTATE Brushless Motor delivers 1800 in. lbs. of fastening torque for faster driving speeds..
REDLITHIUM XC 5.0Ah batteries provide powerful performance..
REDLITHIUM battery technology offers superior pack construction, electronics and performance to deliver exceptional work per charge and work over pack....
Includes 2704-20 1/2 in. hammer drill, 2753-20 1/4 in. hex impact driver, two (2) REDLITHIUM XC 5.0 batteries, M12-M18 multi-voltage charger, (2) belt....

Check Stock

HiLetgo BTS7960 43A High Power Motor Driver Module/Smart Car Driver Module for Arduino Current Limit

5V isolate with MCU, and effectively protect MCU.
Voltage indication of motor driver output end.
Just need four lines from MCU to driver module (GND. 5V. PWM1. PWM2).
isolation chip 5 V power supply (can share with MCU 5 V)..
Able to reverse the motor forward, two PWM input frequency up to 25kHZ.
two heat flow passing through an error signal output..
Isolated chip 5V power supply (can be shared with the MCU 5V), can also use the on-board 5V supply.

Check Stock

MELIFE 5Pack L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Smart Car Power UNO MEGA R3 Mega2560

Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects.
Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient.
No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use.
External size 43*43*27mm / 1.69*1.69*1.06 inch, voltage 5V-35V, drive current 2A (Max single bridge).
Great for Arduino DIY Smart Car Robot Power UNO MEGA R3 Mega2560 Duemilanove. If driving voltage is more than 12V, please use external standard 5volt TTL outputs to switch the H-bridge circuits.

Check Stock

New Version ATX Power Supply Breakout Board and Acrylic Case Kit with ADJ Adjustable Voltage Knob, Supports 3.3V, 5V, 12V and 1.8V-10.8V (ADJ) Output Voltage, 3A Maximum Output, Reset Protection.

1.ATX power supply breakout board, with ADJ adjustable voltage knob, supports 3.3V, 5V, 12V and 1.8V-10.8V (ADJ) output voltage..
2.The voltage output terminals of the ATX power expansion board correspond to each screw terminal..
3. At the same time, the panel is also equipped with an acrylic case kit for easy to use..
4.Compatible with 3.3V: STM32 MCU, network communication equipment, such as Wi-Fi Bluetooth and other devices, generally for microcontrollers, and some low-power modules, etc. 5V: Raspberry Pi, Banana Pi, Tinker Board, Nano Pi, USB interface, etc..
5.Compatible with 9V: Arduino, motor drive, display driver module, etc. 12V: motor drive, LED light, vehicle equipment with power requirements less than 24w, etc..

Check Stock

ATO 7.5 hp 5.5kW VFD, 110V Input 220V Output, 23A , Single Phase to 1phase/3phase Variable Frequency Drive, for Motor Speed Control

Extra-low motor noise offers excellent quietness..
Suit for 3-Phase Nema 17, 23 and 34 Stepper Motor..
Output Current: 1.0 ~ 8.0A, Supply Voltage: 18 ~ 50VDC..
Application areas: engraving machine, filature, wire-stripping machine, marking machine, cutting machine, die bonder, plotter, numerical control machine, automatic assembly equipment etc..

Check Stock

HiLetgo L298P DC Motor Drive Module L298P DC Motor Drive Shield H-Bridge Drive Expansion Board High-Power DC Stepper Motor Controller for Arduino

Driven part of the input voltage VS: VIN Input 6.5 ~ 12V, PWRIN 4.8 ~ 35V input..
The L298P shield DC motor driver has PWM speed control mode.
Adopt dedicated high-power motor driver chip L298P which can directly drive two DC motors with drive current up to 2A..
Stack design can be directly plugged into the Arduino, easier to use..

Check Stock

DORHEA PWM DC Motor Speed Controller DC 10-55V 24V 36V 48V 60A Stepless Motor Speed Controller with Adjustable Potentiometer Forward-Brake-Reverse Switch and LED Digital Display DC Brush Motor

Motor speed controller input supply voltage: DC 10V-55V.
The motor speed controller is an aluminum case, very strong to prevent damage, holes on its side and top which are helpful for heat dissipation..
The pmw dc motor speed controller come with switch function. High power speed controller switch which is much more adaptable and conveniently change the motor direction..
The stepless motor knob adjusts the motor speed from 0% ~ 100% smoothly with LED display is accurate to show 0 ~ 100% of the motor speed..
The input voltage of PWM motor speed controller should be equal to the rated voltage of the motor within 10-55V,or it will be burnt, the dc motor driver can be used to brush motor speed regulation, light dimming regulation in the DC circuit.Note: The motor cannot be used in electric vehicles..

Check Stock

4 Axis CNC Nema23 Stepper Motor Dual Shaft 425oz-in 3A+FMD2740C Driver 40V 4A+400W 36V Power Supply+USB CNC Breakut Board Controller Kit For CNC Router

♞【Product】4 Axis nema23 stepper motor driver usbcnc controller kit.
Wirings: "A+"=Red / "A-"=Green / "B+"=Yellow / "B-"=Blue.
♞【Driver】FMD2740C driver Voltage: DC12-50V.
Current: rated maximum output reaches: 4A.
Subdivision precision 2 8 16 32 64 128 10 20 optional.
♞【4 Axis USBCNC Breakout Board】USB port,only support USB CNC Software,not fit for Mach3 software.Our parcel include a CD,it include the user manual and USBCNC software.
♞【400W 36V 11A DC Switching power supply】Please flip the side input voltage selector switch,Input: AC110V-120V or AC220V-240V.
【Computer system 】Support Win XP/7/8/10,if you can not get the activation code on Win 10,pls let us know,we will help you to solve it..

Check Stock

DEVMO 5pcs DRV8825 Stepper Motor Driver Module with Mini Heat Sink for 3D Printer Accessories Compatible with RepRap 4 RAMPS 1.4 StepStick

★The DRV8825 stepper motor driver carrier board TI DRV8825 micro bipolar stepper motor drive is a breakthrough..
★Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step..
★Simple step and direction control interface..

Check Stock

PWM DC Motor Speed Controller, DC10-55V/40A Max 60A Stepless DC Motor Speed Controller with Forward-Brake-Reverse Switch Adjustable Potentiometer and LED Display,Continuous Current 40A

【Regulate Range】 Input supply voltage: DC 10V-55V.
Control frequency: 15KHZ.Please connect the DC power supply to use! Do not continue to use excessive load, the continuous current is 40A, and the peak value is 60A..
【Switch Function】The PWM DC motor speed controller come with switch function. High power speed controller switch which is much more adaptable and conveniently change the motor direction..
【Excellent Heat Dissipation Performance】 The enclosure of the speed controller for motor is an aluminum enclosure. Aluminum shell is very strong to prevent damage, holes on its side and top which are helpful for heat dissipation..
【Easy to Operate】The stepless motor controller has a simple potentiometer knob adjusts the motor speed from 0% ~ 100% smoothly. And with LED display is accurate to show 0 ~ 100% of the motor speed. The input voltage of PWM motor speed controller should be equal to the rated voltage of the motor within 10-55V,or it will be burnt.Do not reverse the positive and negative poles！.
【Application】 The dc motor driver can be used to brush motor speed regulation, light dimming regulation in the DC circuit.Note: The motor cannot be used in electric veh....

Check Stock

New Milwaukee 2313-21 12 Volt M12 Cordless Inspection Camera System Scope Sale

... FUEL 1/4 in. hex impact driver (2853-20), M18 FUEL SAWZALL reciprocating saw (2821-20), M18 FUEL 6-1/2 in. circular saw (2730-20), M18 FUEL 1/2 in. mid-torque impact wrench (2962-20), M18 FUEL 4-1/2 in./ 5 in. grinder paddle switch, M18 LED work light (2735-20), 2 M18 REDLITHIUM XC 5.0 battery, 1 M18 and M12 multi-voltage charger.

Check Stock