ReviewsMachining Part

Panther Marine 55-2600 Auxiliary Motor Steering Kit - Stainless Steel

  • Brand New RockJock Jeep TJ/LJ/XJ/MJ/ZJ Currectlync Steering System (Part #CE-9701).
  • Compatible with: 1997-2006 TJ/LJ Jeep Wranglers, 1984-2001 XJ Cherokee, 1993-1998 ZJ Grand Cherokee, 1985-1992 MJ Comanche.
  • The RockJock Currectlync heavy duty tie rod and drag link system for TJ, LJ, XJ, MJ and ZJ vehicles features, a 1 1/4″ diameter forged alloy drag link, and 1 1/4″ solid alloy steel tie rod bar that is bored and threaded on the ends. All 7/8″ thread tie rod ends with boots are included as well as the RockJock heavy duty steering stabilizer bracket..
  • This unit is a direct replacement for the stock parts. No modifications or machining to any part of the vehicle is necessary. This unit is rated at 200% stronger than the stock components..
  • NOTE: This unit is designed to be used on vehicles with 4″ of lift. It can be used on vehicles with less lift, but the vehicle must have a minimum of a 2″ bump stop (over stock). Also, on vehicles with no lift, 2 of the tie rod ends may need be trimmed to achieve proper adjustment..
Check Stock

TE-CO 20413 Machinist Clamp Kit, 1/2\ Table T-Slot x 3/8-16\ Stud, 52 Pieces

  • Don't waste your time looking for a clamp, block, stud or nut ever again, this kit has it all packed into one easy to access holder.
  • For workholding during machining applications.
  • 1/2" machine tool table T-slot to fit 1/2" T-slot nuts.
  • Bridgeport type milling machines use Part No. 20402.
  • Made from case hardened 1018 steel with a black-oxide finish.
Check Stock

TE-CO 20402 Machinist Clamp Kit, 5/8\ Table T-Slot x 1/2-13\ Stud, 52 Pieces

  • Don't waste your time looking for a clamp, block, stud or nut ever again, this kit has it all packed into one easy to access holder.
  • For workholding during machining applications.
  • 5/8" machine tool table T-slot to fit 5/8" T-slot nuts.
  • Bridgeport type milling machines use Part No. 20402.
  • Made from case hardened 1018 steel with a black-oxide finish.
Check Stock

TE-CO 20401 Machinist Clamp Kit, 9/16\ Table T-Slot x 1/2-13\ Stud, 52 Pieces

  • Don't waste your time looking for a clamp, block, stud or nut ever again, this kit has it all packed into one easy to access holder.
  • For workholding during machining applications.
  • 9/16" machine tool table T-slot to fit 9/16" T-slot nuts.
  • Bridgeport type milling machines use Part No. 20402.
  • Made from case hardened 1018 steel with a black-oxide finish.
Check Stock

VMTW 8X1 CBN Grinding Wheel 180 Grit 1/4 inch side face for High Speed Steel

  • Straight diamond grinding wheel used for machining of conical, cylindrical and flat surface, cylindrical and conical apertures. Machining of cylindrical surfaces parts and surface ends at one set-up. Machining of recesses and slots of carbide stamps. Sharpening and finishing of carbide tools..
Check Stock

TE-CO 20402PL Machinist Promo Kit, 5/8\ Table T-Slot x 1/2-13\ Stud, 52 Pieces

  • Don't waste your time looking for a clamp, block, stud or nut ever again, this kit has it all packed into one easy to access holder.
  • For workholding during machining applications.
  • 5/8" machine tool table T-slot to fit 5/8" T-slot nuts.
  • Bridgeport type milling machines use Part No. 20402.
  • Made from case hardened 1018 steel with a black-oxide finish.
Check Stock

Amerock Full Inset Full Wrap Free Swinging Minaret Tip Hinge for 3/4\ Doors Oil Rubbed Bronze Single (1)

  • Full 3 way adjustment with one screw to easily adjust a warped door or a twisted cabinet problem.
  • Frame and door machining required - Great for upgrading old hinges without having to make new doors.
  • Use bit (AWM5R) for the door machining and (AWM5AJ) for the face frame machining.
Check Stock

Amerock cm2335ae-XCP5 Non Self-Closing Butt Hinges for Door Hardware 2\ - Pack of 5

  • Full 3 way adjustment with one screw to easily adjust a warped door or a twisted cabinet problem.
  • Frame and door machining required - Great for upgrading old hinges without having to make new doors.
  • Use bit (AWM5R) for the door machining and (AWM5AJ) for the face frame machining.
Check Stock

G-Works Gas Saver Plus Upgrade Cartridge Exchanger Anodize Duralumin

  • Gas Saver PLUS: Save fuel and save resources by collecting remaining gas..
  • New improvements have been made in 2020. Evaporative gas discharge button is included. The outlet located on the rear part and the special check....
  • Assembled brass inserts are designed to prevent thread wear. We have a high quality assembly system through precision CNC machining and developer....
  • G-WORKS company's other products such as butane adapter, LPG adapter and lantern pole set can be used in various applications..
  • Size & Weight: (W) 55 x (D) 20 x (H) 30.7mm, 38g / Material: Super Duralumin (anodizing), Brass / Country of origin: Korea.
Check Stock

Amerock CM7128G10 Self-Closing Face Mount Hinge, 3/8 Inch Inset, Satin Nickel (Sold per Piece)

  • Full 3 way adjustment with one screw to easily adjust a warped door or a twisted cabinet problem.
  • Frame and door machining required - Great for upgrading old hinges without having to make new doors.
  • Use bit (AWM5R) for the door machining and (AWM5AJ) for the face frame machining.
Check Stock

Amerock d3175tbg9-XCP5 Full Inset Full Wrap Cabinet Hinge for Door Hardware - Pack of 5

  • Full 3 way adjustment with one screw to easily adjust a warped door or a twisted cabinet problem.
  • Frame and door machining required - Great for upgrading old hinges without having to make new doors.
  • Use bit (AWM5R) for the door machining and (AWM5AJ) for the face frame machining.
Check Stock