ReviewsMetal Seal Fitting

Westbrass 593144-62 Black 1-1/2 Tubular Tip Toe Bath Waste Drain Kit Matte Black ,Pack of 1

  • 1-1/2 in. x 14 in. Black polypropylene tubes with slip joint washer seal for leak-free fitting.
  • ADA approved tip-toe bath tub drain plug. Press once to close and again to open.
  • Two-hole faceplate with two (2) 1/4 in.-20 x 1-1/2 in. plated brass color matching screws.
Check Stock

FIVKLEMNZ Car Roof Bag Cargo Carrier Door Hooks, Use to Secure Roof Bags Without Need for Roof Rack, 4 Door Hooks Only

  • [NO RACK NEEDED] ROOF MASTER Roof Door Tie Down Hooks can be used as anchor point to secure Rooftop Cargo Carriers without using Side Beams or Cross Beams. This can save you a fortune..
  • [EASY TO FIT] Open door, pull back rubber door seal and fit hook under the welded metal lip. It takes seconds..
  • [SECURE] The anchor point under the door seal on a vehicle is very strong and will take 10X the force required to hold the bag to your roof..
  • [STRONG] Straps are made from high tensile nylon webbing and are flag stitched for strength. This provides the perfect anchor point for the straps that secure your Rooftop Carrier..
  • [INCLUDED] Only 4 X Door Hooks fitting instructions and 12 month warranty. 7×24 online customer support, ask us anything at any time..
Check Stock

Camco 39319 Flexible 3-in-1 Sewer Hose Seal with RhinoExtreme Hose and Handle- Flexible Fitting Makes Connection to a Sewer Inlet Simple and Less Hands On!, Black, Standard

  • The Rhino Sewer Hose Adapter Flexible Drain includes a pre-assembled Rhino Extreme hose with sewer fitting, a 3-in-1 seal adapter and a pull handle. The seal fits in a 3, 3 and 1/2 or 4 inch inlet. No tools or setup required..
  • Adjusts to any angle for better drainage.
  • 3-in-1 seal adapter works with damaged threads.
  • Built-in swivel fitting with odor tight connection.
  • Includes flexible Rhino Extreme and a pull handle.
Check Stock

TEE CSST 1/2 X1/2 X1/2 by PRO-FLEX MfrPartNo PFTE-BBB6

  • 1-piece Retainer Ring that won’t fall off the fitting during installation..
  • Convenient, hand-tightening followed by ¼ to ½ turn with a wrench to seal the fitting..
  • Dual-size, inside-tapped fittings - ask any installer how handy this feature can be..
  • Annealed tube that allows the tubing to bend and stay bent..
  • Same dual-seal, gasket & O-ring fittings work with both traditional yellow and Flak Jacket products..
Check Stock

JoyTube 1” Female PVC Bulkhead Fitting with Plug Silicon Seal Gasket Water Tank Connector for 1-3/4 Inch or 2 Inch Hole Saw Rain Barrels, Aquariums (pack of 2)

  • Size:1 inches female. The PVC Bulkhead Fitting is perfect for 1-3/4 inch or 2 inch hole saw to install.Assemble the bulkhead and hose adapter together.
  • Made of durable PVC material which is no fade, crack and peel..
  • Threaded from the front to end, suitable for industrial and house using. It can be installed in water tank, storage barrel and rain barrels..
  • Package including: 2 pcs bulkhead adapters, 2 pcs plugs and 2 pcs thick silicone seal gaskets..
  • The bulkhead fitting with a thick silicone seal gasket will creates a better tight seal..
Check Stock

Beduan Brass Compression Fitting, Insert Tube Support Compression Sleeve Fitting 1/4\ Tube ID (Pack of 10)

  • ...ade of brass, these compression sleeves ferules are lightweight material but good toughness, high strength, features corrosion resistance and wear resistancee, strong pressure resistance, they are also very easy to assemble. Good sealing performance, no leaks..
  • ✅[FERRULE DESIGN] It is very practical for the tubing fitting. Like cylindrical shaped, bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
  • ✅[HOW IT WORKS] Insert the tubing into the end of the fitting and then tighten it with the nut or screw and then forcing the ferrule into the fitting body. The ferrule design is very practical for the tubing. Like cylindrical shaped, it is bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
  • ✅[APPLICATION] Since these brass compression fittings are good to create the most reliable seal, they can be see anywhere in systems from gas lines in refineries, to the plumbing under your sink, water heater in your home or a pipe transporting thing or your plumbing devices. They are used for fixed locking of copper pipe and hard pipe, PU tube, nylon tube or hard plastic tubing.....
Check Stock

Hilitchi 8Sizes Tube OD 4mm-16mm Brass Compression Sleeves Ferrules Compression Fitting Kit Metric 220Pcs

  • ...de of brass, these compression sleeves ferules are lightweight material but good toughness, high strength, features corrosion resistance and wear resistancee, strong pressure resistance, they are also very easy to assemble. Good sealing performance, no leaks..
  • ✅ [FERRULE DESIGN] It is very practical for the tubing fitting. Like cylindrical shaped, bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
  • ✅ [HOW IT WORKS] Insert the tubing into the end of the fitting and then tighten it with the nut or screw and then forcing the ferrule into the fitting body. The ferrule design is very practical for the tubing. Like cylindrical shaped, it is bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
  • ✅ [APPLICATION] Since these brass compression fittings are good to create the most reliable seal, they can be see anywhere in systems from gas lines in refineries, to the plumbing under your sink, water heater in your home or a pipe transporting thing or your plumbing devices. They are used for fixed locking of copper pipe and hard pipe, PU tube, nylon tube or hard plastic tubin....
Check Stock

Hilitchi 3Sizes Tube OD 1/4 5/16 3/8 Brass Compression Sleeves Ferrules Compression Fitting Kit (SAE, 105Pcs)

  • ...ade of brass, these compression sleeves ferules are lightweight material but good toughness, high strength, features corrosion resistance and wear resistancee, strong pressure resistance, they are also very easy to assemble. Good sealing performance, no leaks..
  • ✅[FERRULE DESIGN] It is very practical for the tubing fitting. Like cylindrical shaped, bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
  • ✅[HOW IT WORKS] Insert the tubing into the end of the fitting and then tighten it with the nut or screw and then forcing the ferrule into the fitting body. The ferrule design is very practical for the tubing. Like cylindrical shaped, it is bulging in the middle but two edges’s diameter are smaller than the belly part so that it could ensure the reliability of a compression seal..
  • ✅[APPLICATION] Since these brass compression fittings are good to create the most reliable seal, they can be see anywhere in systems from gas lines in refineries, to the plumbing under your sink, water heater in your home or a pipe transporting thing or your plumbing devices. They are used for fixed locking of copper pipe and hard pipe, PU tube, nylon tube or hard plastic tubing.....
Check Stock

HANMCE Rubber Sealing Tape Waterproof Tape White, 4in × 5ft (W×L), Outdoor Waterproof Leak Proof Repair Tape for Pools,Sink and Various Pipelines

  • You Will Get: there are 20 rolls of PTFE tapes in blue, with the size of 1/2 inch x 59 feet, sufficient quantity can meet your using and replacement needs.
  • Reliable Material: the plumbing tape is made of PTFE material, which is safe and reliable, high temperature and corrosive resistant, with strong anti aging ability.
  • The tape has good toughness, strong ductility, not easy to break, ensuring the sealing connection is more reliable.
  • Wide Usages: the PTFE thread tape is suitable for most plastic and metal pipe, fitting for both hot and cold water pipe, applied to isolate air and water, forming a tightly seal between the threaded pipes and parts.
  • Convenient to Use: the thread seal tapes are convenient to use.
  • Just clean the 2 threaded connections that need to be sealed.
  • Then wrap the end of the tape around the inner screw joint in the same direction as the rotation direction of the 2 joints.
  • And screw the external thread connector to the internal thread connector wrapped with tape and tighten.
  • Warm Reminders: recommended wrapping the pipe seal tape according to the threading direction, otherwise, it will affect the sealing performance.
  • If the thread sealing is not good, you can increase the thickness of the tape.
Check Stock

WeChef Fully Automatic Cup Sealing Machine 95mm 90mm 88mm 75mm Commercial Electric Cup Sealer 400-670 Cups/Hr Milk Tea

  • ...ti Film & Cup Application]: Adjusting temperature up to 482°F for attaching PP, PE, PS, PET, Easy Ripping film to PP, PET, Paper cups under 7 7/8"(Please notice that sealing film should be suitable for your cup material).
  • Includes 2 15/16", 3 7/16", 3 3/8", 3 3/4" cup holding rings for fitting different cup sizes.
  • [WeChef Automatic Cup Sealer]: Fully automatic in & out operation when putting cup in and touching the pin.
  • With lengthened guide rail to automatically adjust the saucer height according to the cup height.
  • With digital control panel for easy operation, LCD display for showing the real-time counter and temperature.
  • [2 Operation Modes & Safe Automatic Door]: With manual and auto operation modes, if auto mode does not work accidentally, the manual one will continuously work instead, making sure your continuous sealing.
  • When hand touches safe automatic door, the cup holder will be pop out, avoids being pinched.
  • [Wide Application]: Can seal 400 to 670 cups in an hour quickly.
  • Ideal for commercial using in restaurants, mobile beverage trailer, cake shop, dessert shop, drink shop to ....
Check Stock

SCITOO 2pc Water Pump Tool 32mm Fan Clutch Nut Wrench acd Water Pump Holder for BMW for Ford

  • ...ening size before bidding, there are only 32mm 35mm 40mm 45mm, 4 sizes adapters.
  • EASY OPERATION: Completely discharge the old coolant and trapped air first. Use the adapter or work with a suitable adapter sleeve to seat on the radiator opening, rotate the golden knob to seal. Connect the vacuum pump by the brass tee fitting to vacuumize to optimal filling pressure range: -25~-20 inHg. Then take the filling coolant hose to replace the tee fitting to fill coolant. Operate according to the instruction. The filling usually needs 5 to 10mins, depending on the size of the tank.
Check Stock