ReviewsMicro Thrust Bearing

PULSAR 03-07 6.0 Turbo Rebuild Kit 6.6 Duramax LLY LBZ Staggered Step Gap Seals

360º thrust bearing vs. stock 270º thrust bearing enhances turbochargers durability..
Staggered step gap compressor and turbine ends seal rings reduce oil blow by of the seals.
Fits 2003-2007 Ford 6.0L Diesel F250 F350 F450 F550 GT3782VA turbo.
Fits 2004.5-2007 GMC/Chevy 6.6L Duramax LLY LBZ Silverado Sierra HD GT3788VA.

Thrust washers limit axial movement and provide a bearing surface. Thrust bearings are designed to support axial load..
Thrust washers either have multiple tapered ramps and relatively small flat pads or have curved surfaces that follow a sine wave contour around their circumference..
Tear-drop or through grooves on the flange faces and wedge shaped ramps at each parting line allow engine oil to enter between the shaft and bearing surfaces..
Manufactured to meet or exceed OE specifications.

Single-row angular contact ball bearing, supporting moderate to heavy one-directional thrust loads, and combined loads where thrust load is predominant.
Ball contact angle of 40 degrees relative to the inner and outer raceways increases thrust load capacity.
Open configuration for lubrication applied in place.
Brass cage evenly spaces balls for reduced friction, vibration, and noise.
ABEC 1 tolerance ratings for accuracy and low rotational speeds.

Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals on both sides of the bearing keep lubricant in and contaminants out.
Grease fitting on the housing for reapplying lubricant.

Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals on both sides of the bearing keep lubricant in and contaminants out.
Grease fitting on the housing for reapplying lubricant.

Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals on both sides of the bearing keep lubricant in and contaminants out.
Grease fitting on the housing for reapplying lubricant.

Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals on both sides of the bearing keep lubricant in and contaminants out.
Grease fitting on the housing for reapplying lubricant.

Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals on both sides of the bearing keep lubricant in and contaminants out.
Grease fitting on the housing for reapplying lubricant.

Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals and flingers on both sides of the bearing keep lubricant in and contaminants out.
Grease fitting on the housing for reapplying lubricant.

Double-sealed, deep-groove ball bearing insert for applications with radial, thrust, and combined loads.
Cast iron housing and steel bearing unit for carrying shafts with radial or radial and thrust loads.
Set screw locking for secure attachment to shaft.
Contact seals and flingers on both sides of the bearing keep lubricant in and contaminants out.
Grease fitting on the housing for reapplying lubricant.